• Journal of Nutrition and Health
• /
• v.30 no.10
• /
• pp.1219-1228
• /
• 1997

This stusy was designed to develop nutrition education program for the primary school children served by the national school lunch program and to evaluate ist educational effects. Subjects consisted of 61 elementary school children(30 in the control group and 31 in the treatment group) in the 5th grade. Only the treatment group participated in a twelve-week nutrition education program. To evaluate the effects of the nutrition education program, the control and treatment groups were given a pretest and posttest for nutrition knowledge, food attitude, food habits, food preference and plate wastes before and after nutrition education. The results obtained are summerized as follows ; the nutrition knowledge test score (30.4) of the treatment group was significantly higher than that (17.4) of the control group after nutrition education . However, there was no significant difference between the two groups in food attitude test scores after nutrition education. We also did not find any difference induced by nutrition education or the food preferences of the treatment group. After nutrition education , the amount of plate waste of some menus were significantly decreased in the treatment group, but the amount of plate waste of the control group was not significantly changed. However, there was no significant difference in the post test scores above food habits between two groups. It was concluded that a twelve-week nutrition education program can improve nutrition knowledge and decrease plate waste but is not enough to change food attitude , food preference and food habits. It can besard that the two components of foodservice are nutritional foodservice and nutrition education. Foodservice management alone without nutrition education is hardly enough to improve the nutritional status of school children. The result of this study indicate that applying the nutrition education program to elementary school children who are served by the national lunch program can maximize the effects of the national school lunch program.

• Journal of Welding and Joining
• /
• v.29 no.1
• /
• pp.85-89
• /
• 2011

Waste water is disposed to sewage disposal plant by underground PE double wall pipes. Various processes have been introduced to join PE pipes, but most of these methods have many disadvantages such as costs, lack of reliability and difficulties in joining, etc. Recently butt welding has been paid much attention to joint PE pipes as this process has many advantages such as cost, safety and reliability. In this study, newly developed heat plate, a patent-pending heat plate with a groove, was used to butt-weld PE double wall pipes with different misalignment gaps to simulate real underground conditions, and the butt welding temperature of PE pipe was determined by thermal analysis (Thermal Gravimetric Analysis, Differential Scanning Calorimetry and Dynamic Mechanical Analysis). The resulting joining characteristics of double wall pipes were compared with those from a conventional heat plate, in terms of stiffness, flattening and leakage tests. The results from the stiffness and flattening test showed that there were no big differences between the butt-welded joints made from these two plates. From the leakage test, although PE pipes welded with a conventional heat plate did leak below the required test conditions (10 min. at 0.75kgf/cm2), the pipes welded with a patent-pending grooved heat plate did not show any leakage even at a pressure 1.5 times higher than the required conditions. It was noted that by utilizing a grooved heat plate more complete fusion at the pipe joints could be obtained, which in turn induced a high quality joints.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.37 no.9
• /
• pp.1117-1125
• /
• 2013

A finite element based approach that can be used to investigate the plane-view shape and crop loss of a material during plate rolling is presented. We employed a three-dimensional finite element model to continuously simulate the shape change of the head and tail of a plate as the number of rolling passes increases. The main feature of the proposed model lies in the fact that the multistage rolling can be simulated without a break because the rolling direction of the material is reversibly controlled as the roll gap sequentially decreases. The material constants required in the finite element analysis were experimentally obtained by hot tensile tests. We also performed a pilot hot plate rolling test to verify the usefulness of the proposed finite element model. Results reveal that the computed plane-view shapes as well as crop losses by the proposed finite element model were in good agreement with the measured ones. The crop losses predicted by the proposed model were within 5% of those measured from the pilot hot plate rolling test.

• Journal of computational fluids engineering
• /
• v.15 no.4
• /
• pp.53-59
• /
• 2010

Preliminary design of a ground plate, a device installed close to the aircraft model for wind tunnel test to simulate the ground effect, was performed by a numerical simulation. A two-dimensional numerical study was performed initially to decide the optimal leading edge and flap configurations. Then, three-dimensional studies were conducted to decide the optimal flap deflection angle for pressure distribution reduction since the plate and the plate supporting system generate static pressure difference between the upper and lower flow regions. Three-dimensional simulation additionally studied the effect of the clearance between the plate and the wind tunnel side wall. For the efficiency of computation, half model was simulated and a symmetric boundary condition was applied on the center plane. Based on the preliminary design, a ground plate was designed, manufactured and tested at the Korea Aerospace Research Institute(KARI) wind tunnel. The measured pressure differences versus flap deflection angle agreed well with the predicted results.

• Journal of Applied Reliability
• /
• v.17 no.2
• /
• pp.143-149
• /
• 2017

Purpose: In recent years, weight reduction for improving fuel efficiency of the vehicle and cost reduction have been developed. The structure of suspension link is widely used as a single plate press structure which can reduce process and weight compared to existing pipe welding method. However, it was found that the lifetime of a single plate press structure is determined by initial defects that occurred during initial manufacturing rather than fatigue damage caused by driving. Methods: I research the mechanism of failure phenomenon of the single plate press assist arm of rear wheel. In addition, I investigate durability effect parameters to determine the link lifetime in inserting bush into single plate press process through durability test. Conclusion: I discover significant durability effect parameter in inserting bush into single plate press process. It is expected that the durability can be improved by suggesting a bush inserting process inspection guide for similar suspension link like single plate press structure.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.17 no.12
• /
• pp.285-291
• /
• 2016

The purpose of this study was to evaluate the structural capacity of steel pipe pile specimens reinforced with hollow steel plate shear connectors by pull-out test. Compressive strength testing of concrete was conducted and yield forces, tensile strengths and elongation ratios of re-bars and hollow steel plate were investigated. A 2,000kN capacity UTM was used for the pull-out test with 0.01mm/sec velocity by displacement control method. Strain gauges were installed at the center of re-bars and hollow steel plates and LVDTs were also installed to measure the relative displacement between the loading plate and in-filled concrete pile specimens. The yield forces of the steel pipe pile specimens reinforced with hollow steel plate shear connectors were increased 1.44-fold and 1.53-fold compared to that of a control specimen, respectively. Limited state forces of steel pipe pile specimens reinforced with hollow steel plate shear connectors were increased 1.23-fold and 1.29-fold compared to that of a control specimen, respectively. Yield state displacement and limited state displacement of steel pipe pile specimens reinforced with hollow steel plate shear connector were decreased 0.61-fold and 0.42-fold compared to that of a control specimen, respectively.

• Journal of the Korean GEO-environmental Society
• /
• v.12 no.10
• /
• pp.83-90
• /
• 2011

A series of centrifugal model test was conducted to investigate the distribution of vertical earth pressure on circular ductile underground corrugated steel plate waterway culvert with considering the compaction degree of the backfill in the high landfilled embankment section. The compaction degree of backfill was varied to 80, 85, 90, and 95% at the 53g-level gravity considering the similarity of the site. As a result of this test, the load reduction factor by the arching effect of the top of corrugated steel plate showing ductile behavior nearly agreed with the load reduction factor according to the compaction degree of backfill specified in the AISI(2002) design method. The vertical earth pressure measured at the top of the corrugated steel plate was linearly decreased as the compaction degree increased. The greater the compaction degree of backfill was, the greater the reduction of surface loading on the top of the corrugated steel plate by arching effect. The load decreased by arching effect on top of the corrugated steel plate was transferred to the side backfill of the corrugated steel plate(EP 1) and the outside of backfill(EP 3).

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.21 no.11
• /
• pp.86-93
• /
• 2020

The demand for maintenance in Korea infrastructure facilities constructed since the 1970s has increased significantly compared to the demand for new construction. Moreover, after the Gyeongju and Pohang earthquakes, seismic performance evaluation, repair, and retrofitting projects have been carried out. Therefore, in this study, a specimen was designed following the L-type GFRP Plate Externally Bonded Retrofit method, one among other retrofit methods. The L-type GFRP Plate was bonded to the specimen by epoxy and a washered steel nail. A four-point bending test was performed to confirm the strengthening effect of the Externally Bonded Retrofit method using an L-type GFRP Plate. The strengthening effect of the L-type GFRP plate was proven experimentally, and the behavior of the beam designed following the L-type GFRP Plate Externally Bonded Retrofit method was evaluated according to Korea's "Design Manual & Specification for Strengthening of RC Structures by Advanced Composites System". Furthermore, the effectiveness of the bonding method, a combination of epoxy and washered steel nail, was also checked. The results showed that the design, according to the guidelines mentioned above, predicted the strength of the member well, but the failure mode did not satisfy the design assumption because of unexpected damage to the GFRP plate due to the fixing method, washered steel nail.

• Proceedings of the Korean Printing Society Conference
• /
• 2007.11a
• /
• pp.13-28
• /
• 2007

Producing printing plate is essential progress to do offset printing. In this Film-less period, the more PS plate becomes extinct, the more the age of the Plate-Making of Exposure declines the place to stand. To do offset printing, the CTP (Computer to Plate) is taking a place of PS plate that covers speed, quality and economical problems. The biggest advantage of using CTP is that laser directly goes to the plate, thus there are no dust from the Plate-Making of Exposure. It is also theoretically able to print 200lpi${\sim}$300lpi as well as print 1751pi, because it has over 2400dpi resolution. The high quality printing could be available inside of the country, if printing machine keeps the optimum condition in offset printing. The CTP has many advantages, however there is a difficulty for the operators to preserve the equipment. The actual circumstance is that they cannot make a decision about how many dots need to be generated, and also it is necessary to know how to establish the setup at RIP on CTP to make the optimum condition output. If offset printing machine keeps the optimum condition, it would be able to print up to high quality printing however it is hard to comment what is the optimum condition for the printing machine. Anyone could say easy subjectively that machine is in the optimum condition, however it is objectively hard to estimate by number. In this research GATF / Plate Test target used to analyze the image and to make numerical value of the optimum condition of the CTP. It also used GATF / The sheep fed test printing 5.0 to know the density of the color representation, dot gain and gray balance for the optimum condition of the print machine. The purpose of this research is to represent the ISO 12647-2 which is the international standard with domestic printing equipments.

• Journal of the Korean Graphic Arts Communication Society
• /
• v.25 no.2
• /
• pp.69-84
• /
• 2007

Producing printing plate is essential progress to do offset printing. In this Film-less period, the more PS plate becomes extinct, the more the age of the Plate-Making of Exposure declines the place to stand. To do offset printing, the CTP (Computer to Plate) is taking a place of PS plate that covers speed, quality and economical problems. The biggest advantage of using CTP is that laser directly goes to the plate, thus there are no dust from the Plate-Making of Exposure. It is also theoretically able to print $200lpi{\sim}300lpi$ as well as print 1751pi, because it has over 2400dpi resolution. The high quality printing could be available inside of the country, if printing machine keeps the optimum condition in offset printing. The CTP has many advantages, however there is a difficulty for the operators to preserve the equipment. The actual circumstance is that they cannot make a decision about how many dots need to be generated, and also it is necessary to know how to establish the setup at RIP on CTP to make the optimum condition output. If offset printing machine keeps the optimum condition, it would be able to print up to high quality printing however it is hard to comment what is the optimum condition for the printing machine. Anyone could say easy subjectively that machine is in the optimum condition, however it is objectively hard to estimate by number. In this research GATF / Plate Test target used to analyze the image and to make numerical value of the optimum condition of the CTP. It also used GATF / The sheep fed test printing 5.0 to know the density of the color representation, dot gain and gray balance for the optimum condition of the print machine. The purpose of this research is to represent the ISO 12647-2 which is the international standard with domestic printing equipments.