• Journal of the Korean Society for Nondestructive Testing
• /
• v.27 no.4
• /
• pp.299-304
• /
• 2007

There are to be some cracks on the material degradation part or the stress concentration parts of the main members, which carry on over-loads, of structures. Because these cracks can be used to evaluate the structural health status, it is important to monitor the crack growth for maintaining the structural safety. In this study, the fiber Bragg grating sensor with a drop ball was developed as a sensor for crack growth detection of an existing crack. The crack growth detection sensor was constructed with three parts: a probe part, a wavelength controling light source and receiver part, and an impact part. The probe part was just formed with a fiber Bragg grating optical fiber The wavelength controling light source part was composed of a current supplying circuit, a DFB laser diode, and a TEC controling circuit for wavelength control. Also, the impact part was just implemented by dropping a steel ball. The performance of this sensor was confirmed by the experiments of the crack detection with an aluminum plate having one existing crack. According to these experiments, the difference of the sensor signal outputs was correlated with the crack length. So, it was confirmed that this sensor could be applied to monitor the crack growth.

• Journal of Environmental Impact Assessment
• /
• v.27 no.6
• /
• pp.595-603
• /
• 2018

This study was conducted to understand the growth of attached microbial community in small and medium streams of Gyeonggi-do and the removal efficiency of fluoride with changes in growth. The sites monitoring were carried out for 12 weeks at the P1 and P2(P1 is the point where the discharge water flows. P2 is the downstream point of about 2 km flow), and investigated the water quality and the biomass analysis of the attached microbial community. The growth of the attached microbial community increased up to the 7th investigation, and it was observed that detachment phenomenon occurred. Influencing factors about growth of the attached microbial community were flow rate, velocity, and organic material(T-N & T-P). Meanwhile, fluoride content of attached microbial community also tended to increase until the 7th investigation, and decrease from the 8th. It is assumed that fluoride content has also be reduced with the detachment phenomenon of the attached microbial community. It is expected that this will contribute to the evaluation and management of the use of attached microbial community as a means of stream management. The application of techniques using the attached microbial community should include basic investigation of factors that may affect the growth of the attached microbial community and replacement of the attachment plate according to the time of removal.

• Physical Therapy Rehabilitation Science
• /
• v.2 no.2
• /
• pp.70-74
• /
• 2013

Objective: The aim of this study was to determine the impact of the application of whole body vibration training (WBV) on the balance ability of patients with an American Spinal Injury Association (ASIA) type C or D spinal cord injury. Design: Randomized controlled trial. Methods: Twelve patients with spinal cord injury were enrolled in this study. The participants were randomized to an experimental group (n=6) or control group (n=6). The subjects in the experimental group received WBV exercise and the control group received the sham exercise without vibration. The vibrations were adjusted vertically to the patient at a 30 Hz frequency and 3 mm amplitude. The whole body vibration lasted for 16 minutes in total including 5-minutes warm-up and cool-down at the beginning and end of the program, respectively. The static sitting balance ability was assessed by measuring the postural sway while sitting on the force plate with the eyes opened or closed. Postural sway length was measured for 30 seconds with a self-selected comfortable position. Results: In the static balance test, the anterio-posterior, medio-lateral, and total postural sway length with the eyes open and closed was improved significantly before and after the intervention in the experimental group (p<0.05). The experimental group showed significantly more improvement than the control group (p<0.05). Conclusions: Our results demonstrated that WBV training has a positive effect on improving static sitting balance and enhanced control of postural sway in patients with an ASIA-C or D type spinal cord injury.

• Journal of Industrial Technology
• /
• v.21 no.B
• /
• pp.11-20
• /
• 2001

This laboratory study examined the impact of free chlorine residual and pipe material on the formation of biofilm in drinking water distribution pipe surfaces. Result of heterotrophic plate counts(HPC) of the biofilm in the tap water-supplied reactor averaged $2.17{\times}10^5CFU/cm^2$ on PVC and $2.43{\times}10^5CFU/cm^2$ on STS 316, respectively. HPCs on the surface exposed to the tap water containing 0.2mg/L of free chlorinne residual averaged $4.24{\times}10^4CFU/cm^2$ on PVC and $6.54{\times}10^4CFU/cm^2$ on STS 316, respectively. Average of HPC/Total direct counts in the tap water-supplied reactor ranged from 1.08%(PVC) to 1.26%(STS 316) and from 0.38%(PVC) to 0.65%(STS 316) in the reactor supplemented with disinfectant, respectively. No correlation was observed between disinfectant addition and biofilm density. With regard to the biofilm formation, little difference existed between PVC and STS 316. Yellow and red pigmented bacteria were the dominant expressions in bulk fluid, whereas non-pigmented bacteria were found dominant in the biofilm. Pink/red pigmented bacteria were found to be facultative anaerobic, while yellow pigmented bacteria and non-pigmented bacteria were found to be obligate aerobic.

• Asian Pacific Journal of Cancer Prevention
• /
• v.14 no.6
• /
• pp.3677-3680
• /
• 2013

We aimed to assess the role of XPG, XPC and MMS19L polymorphisms on response to chemotherapy in osteosarcomas, and the clinical outcomes. One hundred and eighty five osteosarcoma patients who were histologically confirmed were enrolled in our study between January 2007 and December 2009. Genotyping of XPG, XPC and MMS19L was performed in a 384-well plate format on the MassARRAY$^{(R)}$ platform. Individuals with XPG TT genotype and T allele were more likely to be better response to chemotherapy than CC genotype, with the OR (95% CI) of 4.17 (1.64-11.54) and 2.66 (1.39-5.11), respectively. Those carrying MMS19L TT genotype and T allele showed better response to chemotherapy, with ORs (95% CI) of 4.8 (1.56-17.7) and 2.3 (1.22-4.36), respectively. Patients carrying TT genotype of XPG and MMS19L showed a significantly longer overall survival than CC genotype, with a 0.47 and 0.30-fold risk of death when compared with the wild-type of the gene. XPG and MMS19L are correlated with response to chemotherapy and prognosis of osteosarcoma, so that they could be used as predictive markers for prognosis.

• Korean Journal of Applied Biomechanics
• /
• v.25 no.2
• /
• pp.199-206
• /
• 2015

Objective : The purpose of this study was to conduct a biomechanical analysis of a one-legged jump in a traditional Korean dance (Wae Bal Ddwigi) according to breathing method. Method : Participants for this study were 10 dancers with experience for at least 10 years in traditional Korean dance. Independent variables for this test were two different types of breathing methods. Dependent variables were ground reaction force and lower extremity kinematic variables. The jumping movement was divided into three separate stages, take off, flight, and landing. The subjects were asked a questionnaire regarding the degree of impact force and stability of landing posture after the experiment. The Kistler Force Plate (9281B, Switzerland) was used to measure ground reaction force. A digital camera was used to look into angles of each joint of the lower part of body. SPSS was used for statistical analysis via the dependent t-test(p<.05). Results : There were significant differences in jumping according to breathing method. The inhalation & exhalation method yielded significantly longer flight times combined with greater ground reaction force. The breath-holding method required more core flexion during landing, increasing movement at the hips and shoulders. Conclusion : Consequently, there was more flexion at the knee to compensate for this movement. As a result, landing time was significantly higher for breath-holding.

• Journal of Advanced Marine Engineering and Technology
• /
• v.33 no.1
• /
• pp.104-111
• /
• 2009

This paper shows the behaviors of macro- and micro-structures and mechanical properties for specimen's welding region welded by FSW. according to welding conditions with 5mm thickness aluminum 5083O alloy plate. It apparently results in defect-free weld zone in case traverse speed was changed to 32 mm/min under conditions of anti-clockwise direction and tool rotation speed such as 800 and 1250 rpm with tool's pin diameter of 5 ${\Phi}mm$ and shoulder diameter of 20 ${\Phi}mm$, pin length of 4.5 mm and tilting angle of $2^{\circ}$. The ultimate stress of ${\sigma}_T=331$ MPa and the yield point of 147 MPa are obtained at the condition of the travel speed of 32 mm/min with the tool rotation speed of 1250 rpm. There is neither voids nor cracks on bended surface of $180^{\circ}$ after bending test. The improvement of toughness after impact test was found. The lower rotating and traverse speed became, the higher were yield point, maximum stress and elongation(%) with the stresses and the elongation(%) versus the traverse speed diagram. Vickers hardness for cross section of welding zone were also presented. The typical macro-structures such as dynamically recrystallized zone, thermo-mechanically affected zone and heat affected zone and the micro-structures of the transverse cross-section were also showed. However, the author found out that the region of 6mm far away from shoulder circumference was affected by friction heat comprehensively, that is, hardness softened and that part of micro-structures were re-solid-solution or recrystallized, the author also knew that there is no mechanically deformation on heat affected zone but there are the flow of plastic deformation of $45^{\circ}$ direction on thermo-mechanically affected zone and the segregation of Al-Mg on nugget. The solid solution wt(%) of parent material as compared against of friction stir welded zone was comprehensively changed.

• Journal of Korean Society of Steel Construction
• /
• v.24 no.4
• /
• pp.399-410
• /
• 2012

In this study, vibration tests are performed on cantilevered and clamped-clamped laminated composite rectangular plates using experimental modal analysis technique. The damages are simulated by applying progressive line cracks to the laminated composite plates for damage evaluations due to crack growth. The changes of frequency response functions(FRFs), MAC values, and modal parameters (frequency, mode shape and damping ratio) of the damaged composite plates, which are obtained by the modal testing of impact hammer, are investigated. Each experimental modal parameter of the progressively damaged composite plates is compared with natural frequencies and mode shapes obtained by finite element analysis. It is seen that the damage can be evaluated from the changes in the geometric properties and structural behaviors of the laminated composite plates resulting from the model updating process of the finite element model as a benchmark.

• Journal of Ocean Engineering and Technology
• /
• v.21 no.3 s.76
• /
• pp.71-76
• /
• 2007

Recently, many industries have been employing the application of laser beam welding, due to the resulting high welding quality, such as smaller width of melting and heat affective zone, smaller welding deformation, and fine grains of weldment, compared to arc welding. However, in order to appropriately utilize this welding process with steel structure, the characteristics of welding residual stresses and fracture toughness in welded joints are to be investigated for reliability. Therefore, in this study, the mechanical properties of weldments by arc and laser welding are investigated using FEM to confirm the weldability of laser welding to the general structural steel (HT50). The Charpy impact test and 3-points bending CTOD test are carried out in the range of temperatures between $-60^{\circ}C\;and\;20^{\circ}C$, in order to understand the effect on the fracture toughness of weldments. From the research results, it has been found that the maximum residual stress appears at the center of plate thickness, and that the fracture toughness is influenced by strength mis-match.

• Journal of Korean Neurosurgical Society
• /
• v.54 no.6
• /
• pp.496-500
• /
• 2013

Objective : To evaluate the successful fusion rate in postmenopausal women with single-level anterior cervical discectomy and successful fusion (ACDF) and identify the significant factors related to bone successful fusion in pre- and postmenopausal women. Methods : From July 2004 to December 2010, 108 consecutive patients who underwent single-level ACDF were prospectively selected as candidates. Among these, the charts and radiological data of 39 women were reviewed retrospectively. These 39 women were divided into two groups : a premenopausal group (n=11) and a postmenopausal group (n=28). To evaluate the significant factors affecting the successful fusion rate, the following were analyzed : the presence of successful fusion, successful fusion type, age, operated level, bone mineral density, graft materials, stand-alone cage or plating with autologous iliac bone, subsidence, adjacent segment degeneration, smoking, diabetes mellitus, and renal disease. Results : The successful fusion rates of the pre- and postmenopausal groups were 90.9% and 89.2%, respectively. There was no significant difference in the successful fusion rate or successful fusion type between the two groups. In the postmenopausal group, three patients (10.8%) had successful fusion failure. In the postmenopausal group, age and subsidence significantly affected the successful fusion rate (p=0.016 and 0.011, respectively), and the incidence of subsidence in patients with a cage was higher than that in patients with a plate (p=0.030). Conclusion : Menopausal status did not significantly affect bone successful fusion in patients with single-level ACDF. However, in older women with single-level ACDF, the combination of use of a cage and subsidence may unfavorably affect successful fusion.