• 한국농공학회지
• /
• 제34권1호
• /
• pp.41-48
• /
• 1992

Various soil behaviors usually occurring in the geotechnical problems, such as, cutting and embankments, stability of slope, seepage, consolidations, shearing failures and liquefaction, should be predicted and analyzed in any way. An approach of these predictions may be followed by the development of the constitutive equations as first and subsequently solved by numerical methods. The purpose of this paper is develop the constitutive equation of sands uder monotonic or cyclic loadings. The constitutive equation which is based on elasto-plastic theory, modified anisotropic consolidated stress parameter by Sekiguchi et al and Pender's theory is derived. And the equation is included a new stress parameter, hardening function, Bauschinger's effects and Pender's theory. The model is later evaluated and confirmed the validity by the test data of Ottawa sand, Banwol sand Hongseong sand. The following conclustions may be drawn: 1. The consititutive equation which is based on elasto-plastic theory, modified anisotropic consolidated stress parpameter by Sekiguchi et al and Pender's theory is derived. The equation in included a new stress parameter, hardening function, Bauschinger's effect and Pender's theory. 2. For Ottawa sand, the result of the constitutive equation shows a better agreement than that of Oka et al. The result of axial strain agrees well with the tested data. However, the result of horizontal strain is little bit off for the cyclic loadings or large stress. It is thought that the deviation may be improved by considering Poisson's ratio and precise measurement of shear modulus. 3. Banwol sand is used for the strain and stress tests with different relative densitites and confining pressures. The predeicted result shows a good agreement with the tested data because the required material parameters were directly measurd and determined form this laboratory. 4. For Hongseong sand, the tests under same amplitude of cyclic deviatoric stress shows a similar result with the tested data in absolute strain. It shows the acute shape of turning point because the sine wave of input is used in the test but the serrated wave in prediction.

• 지질공학
• /
• 제8권3호
• /
• pp.215-224
• /
• 1998

LVDT에 의해 전체변형율이 측정되었고, 국부적 변형율은 변형율게이지에 의해 측정되었다. 또한 공시체에서의 응력 분포를 알기 위하여 유한요소법에 의한 축대칭 탄소성 해석을 하였다. 단면구속영향을 고려하면 H/D=1인 경우에 특히 구속영향을 크게 받는다. 또한 공시체 직경에 대한 공시체 길이가 길어질수록 영향을 적게 받는다는 것을 알 수 있다. 공시체와 재하판과의 접촉면에서 응력 및 변위 분포는 접촉하고 있는 두 재료의 탄성계수비와 접촉면의 마찰저항에 크게 좌우된다. 즉 암석공시체에 대한 재하판의 영향은 경암에서보다 연암에서 더 현저하다 또한 단면구속이 변형율 분포에 미치는 영향 및 치수효과는 강성이 큰 암석에서 현저하게 나타난다.

• 한국안전학회지
• /
• 제29권5호
• /
• pp.15-21
• /
• 2014

The aim of this work is conduct the study on light weight and structural performance improvement of the composite wind power blade. GFRP (Glass Fiber Reinforced Plastic) pre-empted by CFRP(Carbon Fiber Reinforced Plastic), the major material of wind power blade, was identified the superiority of mechanical performance through the tensile and fatigue test. SENT(Single Edge Notched Tension) specimen fracture test was conducted on the specimen that laminated together 2 ply CFRP with 4 ply GFRP through DIC(Digital Image Correlation) analysis. The SENT specimen thickness and $a_0/W$ ratio is 1.45 mm and 0.2, respectively. The fracture test accomplished with displacement control with 0.1 mm/min at the room temperature. The experimental apparatus used for the fracture test consisted of a 50kN universal dynamic tester and CCD camera connected to a personal computer (PC), which was used to record images of the specimen surface. Following data acquisition, the images and load-displacements were transferred to the PC, on which the DIC software was implement. The experiment and DIC analysis results show that CFRP/GFRP laminated composite exhibits improvement of the strength, compared with that of the existing blade material. This study shows the result that the strength of CFRP rotor blade of wind turbine satisfies through the experimental and DIC method.

• Steel and Composite Structures
• /
• 제23권2호
• /
• pp.229-238
• /
• 2017

This paper presents a combined numerical and theoretical study on the composite action between steel and concrete of circular steel tube confined concrete (STCC) stub columns under axial compressive loading with a full theoretical elasto-plastic model and finite element (FE) model in comparison with experimental results. Based on continuum mechanics, the elasto-plastic model for STCC stub columns was established and the analysis was realized by a FORTRAN program and the three dimensional FE model was developed using ABAQUS. The steel ratio of the circular STCC columns were defined in range of 0.5% to 2% to analyze the composite action between steel tube and concrete, and make a further study on the advantages of the circular STCC columns. By comparing the results using the elasto-plastic methods with the parametric analysis result of FE model, the appropriate friction coefficient between the steel tube and core concrete was defined as 0.4 to 0.6. Based on ultimate balance theory, the formula of ultimate load capacity applying to the circular STCC stub columns was developed.

• 한국전산구조공학회:학술대회논문집
• /
• 한국전산구조공학회 1998년도 가을 학술발표회 논문집
• /
• pp.290-297
• /
• 1998

In this paper, we propose to a method to estimate the elasto-plastic buckling for single layer latticed domes. First, we assume that each member consists of the rigid zone and elastic spring at both end joint, the elastic element and three elasto-plastic spring to judge for yeilding the member. Next, the member which has most influence on buckling for structures is determined by a distributed pattern of the strain energy which is calculated through linear eigenvalue analysis. And then, normalized slenderness ratio of the element is derived considering the axial force at elastic buckling load. Later, we execute elasto-plastic nonlinear analysis that based on loading increasement method and displacement increasement method. From this results, we discusses the effect of the joint rigidity and the half open angle $\theta$$_{0}$ on the buckling strength of single layer lattice domes ; (1) how the joint rigidity contributes to the reduction of buckling loads, (2) how the reduction can be interrelated to compressive strength curves in terms of the generalized slenderness for the member most relevant to the overall buckling of domes.s.

• 한국지반공학회논문집
• /
• 제20권5호
• /
• pp.145-159
• /
• 2004

본 연구에서는 지진시 지반의 안정성 평가시, 진동시험에 기초하여 액상화 발생가능성 여부를 판정하는 상세평가법을 개발하였다. 개발된 평가법에서는 기존의 평가법이 지진을 단순히 정현하중화하는 등가전단응력개념에 기초한점과는 달리, 지진의 최대가속도, 유효지속시간, 지진형태, 그리고 지진규모 등 다양한 지진영향인자가 고려될 수 있도록 실지진기록 입력의 지반응답해석을 포함하도록 하였다. 지반의 고유한 저항특성을 응력-변형률 시험 결과로부터 액상화 전환시점까지의 누적 소성 전단변형률로 하였으며 이와 연계하여 지진의 액상화 발생특성을 지반응답해석을 통해 획득 가능한 전단변형률 시간이력곡선에 기초하도록 하였다. 이때, 액상화를 유발시키는 실지진기록의 특성분석을 위해 실지진하중 재하의 진동삼축시험을 수행하였다. 시험결과, 충격형 지진인 경우, 지진기록의 최대하중이 재하된 직후, 과잉간극수압이 급진적으로 발전하며 액상화가 발생하는 것으로 나타났으며 진동형 지진의 경우에는 최대하중이 재하된 경우, 눈에 띄는 과잉간극수압의 변화가 관찰되었으며 이후, 일정수준 이상의 큰 하중재하시 액상화가 발생하였다. 이로부터 액상화 발생에 가장 큰 영향인자는 최대하중인 것을 알 수 있었으며 진동형 지진형태의 경우, 일정수준 이상의 후속하중에 대한 고려가 필요함을 알 수 있었다. 이상의 결과로부터 본 평가법에서는 우선적으로 충격형 지진에 한하여 사용할 것을 제안하며 이때, 최대 전단변형률까지의 시간이력곡선으로부터 소성 전단변형률을 누적계산하여 이를 해당입력지진의 액상화 발생특성치로 정하였다. 기존의 등가응력개념에 기초한 상세평가법과의 비교를 통한 타당성 분석결과, 본 평가법은 기존의 상세평가법보다 유효응력경로 및 응력-변형률 상관곡선 등 실제적인 지반거동변화에 관한 진동시험결과에 기초하여 지반의 고유특성을 결정하고 지반응답해석을 통해 증폭현상을 포함한 지반 내 지진거동변화와 지진시간이력이 보유하고 있는 지진특성을 충분히 반영하고 있으므로 신뢰성 높은 액상화 상세평가가 가능할 것으로 판단된다.

• 한국강구조학회 논문집
• /
• 제23권4호
• /
• pp.405-415
• /
• 2011

건축물의 안전한 내진설계를 위해서는 층간변위비 뿐만 아니라 부재에 요구되는 소성변형을 평가하여야 한다. 본 연구에서는 복잡한 비선형해석 없이 탄성해석을 사용하여 강기둥-약보로 설계된 철골 특수모멘트골조의 보에 요구되는 소성변형을 평가하는 간편한 방법을 개발하였다. 개발한 방법은 탄성해석 결과를 근거로 모멘트 재분배, 기둥 단면치수 및 보 소성힌지 이동, 패널존 변형, 중력하중, 변형경화 거동 등을 고려하여 보의 소성변형각을 직접적으로 예측한다. 또한 가새골조 또는 코어벽 등 횡력 저항구조와 모멘트골조의 상호 작용인 로킹 효과 고려한다. 검증을 위하여 강기둥-약보로 설계된 6층 특수모멘트골조에 제안된 방법을 적용하여 보의 소성변형각을 예측하고, 그 결과를 비선형 해석 결과와 비교하였다. 검증 결과, 제안된 방법은 설계 변수에 따른 보의 소성변형각을 합리적으로 예측하는 것으로 나타났다.

• Computers and Concrete
• /
• 제4권5호
• /
• pp.377-402
• /
• 2007

The paper presents quasi-static plane strain FE-simulations of strain localization in reinforced concrete beams without stirrups. The material was modeled with two different isotropic continuum crack models: an elasto-plastic and a damage one. In case of elasto-plasticity, linear Drucker-Prager criterion with a non-associated flow rule was defined in the compressive regime and a Rankine criterion with an associated flow rule was adopted in the tensile regime. In the case of a damage model, the degradation of the material due to micro-cracking was described with a single scalar damage parameter. To ensure the mesh-independence and to capture size effects, both criteria were enhanced in a softening regime by nonlocal terms. Thus, a characteristic length of micro-structure was included. The effect of a characteristic length, reinforcement ratio, bond-slip stiffness, fracture energy and beam size on strain localization was investigated. The numerical results with reinforced concrete beams were quantitatively compared with corresponding laboratory tests by Walraven (1978).

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2007년도 춘계학술대회A
• /
• pp.1830-1835
• /
• 2007

In the present work, the effect of strength mismatch on plastic limit loads is quantified for strength-mismatched plates with constant-depth surface cracks under tension, via three-dimensional, small strain elastic-perfectly plastic finite element analyses. Relevant variables related to plate and crack geometries are systematically varied, in addition to the weld width. An important finding is that a parameter related to the weld width-to-ligament ratio is proposed, based on which limit loads can be uniquely quantified. The proposed limit load solutions is a valuable input to estimate nonlinear fracture mechanics parameters based on the reference stress approach.

• 대한기계학회논문집A
• /
• 제32권5호
• /
• pp.411-418
• /
• 2008

In this work, the effect of strength mismatch on plastic limit loads is quantified for similar metal weld plates with cracks under tension load, via three-dimensional, small strain elastic-perfectly plastic finite element analyses. Relevant variables related to plate geometry and crack length are systematically varied, in addition to the weld width. An important finding is that mis-match limit loads can be uniquely quantified through strength mis-match ratio and one geometry-related parameter. Based on the proposed limit load solutions, reference stress based J-integral estimates is also investigated. When the reference stress is defined by the mis-match limit load, predicted J-integral values agree overall well with FE results.