• 콘크리트학회논문집
• /
• 제22권5호
• /
• pp.675-684
• /
• 2010

철근콘크리트 부재는 연성파괴를 유도하기 위해서 휨인장 파괴가 선행 하도록 구조설계한다. 또한 보에서 파괴가 진행하도록 하여 기둥에는 피해가 적게 발생하도록 한다. 하지만 소성붕괴메카니즘에 의하여 소성힌지는 보의 양단부에 발생한 이후 최종적으로 최하층 기둥의 하부에도 발생한다. 철근콘크리트 구조물의 최하층 기둥은 축력이 크게 작용하고 전단경간이 비교적 작기 때문에 휨항복을 했다고 하더라도 최종적으로는 전단파괴하거나 부차파괴하여 설계보다 취성적으로 파괴 할 가능성이 있다. 이 논문에서는 휨항복 후 전단파괴하는 10개의 실험체를 통해 소성힌지 영역의 변형율과 길이 확장에 주는 요소에 대해 파악하였다. 실험결과 세 변수 중에서 축력이 가장 크게 영향을 미쳤는데 축력이 클수록 축방향 변형률과 연성비가 뚜렷하게 줄어드는 현상을 확인할 수 있었으며 소성힌지 길이는 약간 늘어났다. 실험을 통해서 산출한 소성힌지 길이는 약 0.7~1.4d였으며 이는 기존 연구자들이 제안했던 평가식과 차이를 보여주었다.

• 콘크리트학회논문집
• /
• 제25권1호
• /
• pp.19-28
• /
• 2013

소성힌지 구역의 축방향변형률의 예측은 지진하중을 받는 철근콘크리트 기둥의 합리적인 연성 평가를 위하여 필요한 항목이다. 축방향변형률은 콘크리트의 유효압축강도를 저하시키고 층간 변위를 크게 할 수 있다. 기존 연구는 주로 소성힌지가 발생하는 보의 축방향변형률 예측에 국한되었지만 횡력을 받는 구조물에서는 저층부 기둥도 소성힌지가 발생한다. 이 논문에서는 기둥 부재에 작용하는 축력의 크기에 따라 변화하는 축방향변형률을 예측할 수 있는 모델과 평가식이 제안되었다. 단면 해석법을 이용하여 하중이력에 따른 축방향변형률의 변화와 철근의 변형률 변화를 고찰한 후, 해석과 실험 결과를 근거로 축방향변형률 예측 모델을 제안하였다. 제안된 모델은 부재 축방향변형률을 3가지 경로(재하, 재하 후 반대하중이 하중이 가해지는 구간, 동일한 부재 회전각에서 반복하중을 받을 구간)로 구분하였다. 이 연구에서 제안된 기둥 부재의 축방향변형률의 계산식은 축력비가 다른 철근콘크리트 기둥의 실제 축방향변형률을 추적하였고, 축력비의 영향을 반영하였다.

• Earthquakes and Structures
• /
• 제10권2호
• /
• pp.329-350
• /
• 2016

A parametric study was conducted to investigate the seismic deformation demands in terms of drift ratio, plastic base rotation and compression strain on rectangular wall members in frame-wall systems. The wall index defined as ratio of total wall area to the floor plan area was kept as variable in frame-wall models and its relation with the seismic demand at the base of the wall was investigated. The wall indexes of analyzed models are in the range of 0.2-2%. 4, 8 and 12-story frame-wall models were created. The seismic behavior of frame-wall models were calculated using nonlinear time-history analysis and design spectrum matched ground motion set. Analyses results revealed that the increased wall index led to significant reduction in the top and inter-story displacement demands especially for 4-story models. The calculated average inter-story drift decreased from 1.5% to 0.5% for 4-story models. The average drift ratio in 8- and 12-story models has changed from approximately 1.5% to 0.75%. As the wall index increases, the dispersion in the calculated drifts due to ground motion variability decreased considerably. This is mainly due to increase in the lateral stiffness of models that leads their fundamental period of vibration to fall into zone of the response spectra that has smaller dispersion for scaled ground motion data set. When walls were assessed according to plastic rotation limits defined in ASCE/SEI 41, it was seen that the walls in frame-wall systems with low wall index in the range of 0.2-0.6% could seldom survive the design earthquake without major damage. Concrete compressive strains calculated in all frame-wall structures were much higher than the limit allowed for design, ${\varepsilon}_c$=0.0035, so confinement is required at the boundaries. For rectangular walls above the wall index value of 1.0% nearly all walls assure at least life safety (LS) performance criteria. It is proposed that in the design of dual systems where frames and walls are connected by link and transverse beams, the minimum value of wall index should be greater than 0.6%, in order to prevent excessive damage to wall members.

• Composites Research
• /
• 제36권5호
• /
• pp.369-376
• /
• 2023

본 연구에서는 복합소재의 기지재로 활용되고 있는 에폭시 고분자의 가교율이 항복표면에 미치는 영향을 분자동역학 해석을 통해 평가하고자 한다. 분자동역학 해석을 활용하여 가교율에 따른 에폭시 모델을 형성한 후, 상온-대기압 조건하에서 단축 변형 해석 및 평면응력 조건을 고려한 다축 변형 해석을 수행하였으며, 해석 데이터를 통하여 가교율에 따른 영률, 항복점, 항복표면, 그리고 경화지수를 도출하였다. 해석 결과, 영률 및 응력은 기존 선행 연구들에서 조사되었듯이, 가교율에 따라 증가하는 경향을 확인하였다. 다축 변형 시에는, 이러한 가교율과 도출된 응력간의 관계가 하중의 방향에 따라 의존적임을 확인하였는데, 가교율이 증가할수록 단축 인장 영역에 비해, 이축 압축 영역의 항복표면은 빠른 속도 팽창하였으며, 이로 인한 항복표면의 상이함을 관측하였다. 이를 통해, 고분자 소재의 항복 표면의 압력의존성은 소재의 가교 정도에 의존적이며, 항복이 진행될수록, 압력의 존성은 동일 소재 하에서도 변할 수 있음을 확인하였다.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2000년도 춘계학술대회논문집A
• /
• pp.194-199
• /
• 2000

The creep rate is affected by the temperature and in fact. if the temperature above $T_M/2(T_M:melting\;point)$. The aim of the present investigation is to study the relationship of static creep and cyclic creep behavior of pure copper and the formulation of these phenomena with the special attention to the instantaneous strain. strain rate from time and number of cycles have the same inclination Steady state creep rate depend upon maximum stress and can be expressed as linear function according to Power law creep equations Creep rupture time has relation with creep rate. and it make a group represented as the same direct line regardless of max stress, stress ratio and the temperature. Initial strain effect on continuous creep deformation. and have guantitative relationship between elastic and Plastic strain. LMP have similar tendency than OSDP and MHP according to temperature

• 한국해양공학회지
• /
• 제12권2호통권28호
• /
• pp.57-64
• /
• 1998

This study is concerned with criterion for membrane to shell conversion in two-dimensional elastic-plastic finite element analysis using membrane/shell mixed element. It is well known that in the sheet metal forming some parts of the sheet deform under almost pure stretching (membrane) conditions, whereas other parts in contact with sharp tooling surfaces can develop significant bending strains. The membrane analysis has a short computational time however, in the membrane analysis the bending effects can not be condidered at all. On the other hand, the shell analysis allows the consideration of bending effects, but involves too much computational time. So Onatel),2), Yang et al3),4) developed the membrane/shell mixed element. Onate introduced the energy ratio parameter and Yang et al introduced the ratio of thickness to radius of curvature as the criterion. In the present study we propose a new criterion by using the angle between both side elements in the nodal point.

• 소성∙가공
• /
• 제24권6호
• /
• pp.395-399
• /
• 2015

A microstructure-based finite element simulation was conducted to predict the plastic strain ratio (R-value) of a dual-phase (DP) steel. The representative volume elements (RVEs) concept was adopted for the image-based FE modeling and a 3D model was constructed using sequential 2D images. Each phase was considered with the von-Mises yield criterion and the Swift model. The Swift parameters were defined by the empirical equations based on the chemical composition. The developed model was applied to analyze the effect of residual stress on the R-value and stress distribution. In order to consider the residual stress development after cold rolling, 10 % compression was applied in the thickness direction and unloaded before the tensile stress was applied in the rolling direction. The results showed a reasonable prediction for the R-value evolution: a sharp increase at small strains was well described and a transition followed in the downward direction. The R-value evolution was analyzed using the stress distribution change on the π-plane

• Structural Engineering and Mechanics
• /
• 제69권6호
• /
• pp.627-635
• /
• 2019

In order to study the axial compression performance of sand-lightweight concrete-filled steel tube (SLCFST) stub columns, three circular SLCFST (C-SLCFST) stub column specimens and three SLCFST square (S-SLCFST) stub column specimens were fabricated and static monotonic axial compression performance testing was carried out, using the volume ratio between river sand and ceramic sand in sand-lightweight concrete (SLC) as a varying parameter. The stress process and failure mode of the specimens were observed, stress-strain curves were obtained and analysed for the specimens, and the ultimate bearing capacity of SLCFST stub column specimens was calculated based on unified strength theory, limit equilibrium theory and superposition theory. The results show that the outer steel tubes of SLCFST stub columns buckled outward, core SLC was crushed, and the damage to the upper parts of the S-SLCFST stub columns was more serious than for C-SLCFST stub columns. Three stages can be identified in the stress-strain curves of SLCFST stub columns: an elastic stage, an elastic-plastic stage and a plastic stage. It is suggested that AIJ-1997, CECS 159:2004 or AIJ-1997, based on superposition theory, can be used to design the ultimate bearing capacity under axial compression for C-SLCFST and S-SLCFST stub columns; for varying replacement ratios of natural river sand, the calculated stress-strain curves for SLCFST stub columns under axial compression show good fitting to the test measure curves.

• KIEAE Journal
• /
• 제8권5호
• /
• pp.61-68
• /
• 2008

For the recycling of the resources and the preservation of the environment, this study's purpose is to measure flexural behavior of the reinforced concrete beams with the major variables like concrete strength, replacement ratio of the recycled aggregate and the waste foundry sand and the tension reinforcement ratio and to present the data of the recycled aggregate used for the structure design. The experiment on the flexural behavior resulted in the followings. The ultimate strength of recycled R/C beam was manipulated proportionate to the tension reinforcement ratio, however the strength instantly decreased after passing the ultimate load due to the destroyed concrete of the compression side. The deflection at the maximum load varied from the tension reinforcement ratio by 5.5 times. The test specimen with the tension reinforcement ratio less than $0.5{\rho}b$ showed constant curve without change in the load from the yield to the ultimate load in contrast to the distinctive plastic region where the displacement was rising. Although the strain of main tension steel with the reinforcement ratio indicate different, the design of recycled concrete member can be applied for current design code for reinforced concrete structure as the ratio of tension reinforcement district the under the reinforcement ration in a balanced strain condition.

• 콘크리트학회논문집
• /
• 제19권4호
• /
• pp.441-448
• /
• 2007

지진하중을 받는 철근콘크리트 접합부의 거동은 전단과 부착 메커니즘에 의해 결정된다. 하지만 전단과 부착은 반복하중에 매우 취약하기 때문에 접합부는 항상 탄성 영역 내에 있어야 한다. 내진 설계 기준에서는 보에 소성힌지를 발생시켜 기둥과 접합부는 탄성 상태를 유지하면서 보에서 에너지소산이 이루어지도록 하는 것을 원칙으로 한다. 하지만 접합부와 인접한 보에 소성힌지가 발생할 경우, 보에서 발생한 소성힌지에서의 철근 변형률이 접합부 철근의 변형에 영향을 미쳐 결국 접합부의 전단 및 부착강도를 떨어뜨리는 결과를 가져오게 된다. 본 논문에서는 보 인장 철근량을 변수로 한 다섯 개의 철근콘크리트 보-기둥 접합부를 제작하고 보에 소성힌지를 발생시킨 후 그 결과를 분석하였다. 실험 결과, 보 인장철근량이 적을수록 접합부의 연성은 증가하였다. 또한 소성힌지 영역의 철근이 항복함에 따라 접합부의 연성률이 증가하고 접합부의 보 부재축 방향 인장변형률도 증가하였다.