• 한국안전학회지
• /
• 제17권4호
• /
• pp.146-152
• /
• 2002

The steel shows plastic deformation after the yield point exceeds. Because of overloads, the plastic deformation occurs at the interior support of a continuous bridge. The plastic deformation is concentrated at the interior support, and the permanence deformation at the interior support remains after loads pass. Because local yielding causes the positive moment at the interior support, it is called "auto moment". Auto moment redistributes the elastic moment. Because of redistribution, auto moment decreases the negative moment at the interior support of a continuous bridge. In this paper, the moment-rotation curve from Schalling is used. The Plastic rotation is computed by using Beam-line method, and auto moment is calculated based on the experiment curve. The design example is presented using limit state criterion.

• 대한물리의학회지
• /
• 제13권1호
• /
• pp.99-105
• /
• 2018

PURPOSE: The aim of this study was to evaluate the concurrent validity and clinical usefulness of the universal plastic goniometer to measure the range of motion of the internal and external rotation of the hip joint using the three dimensional motion analysis which can analyze the joints and segment movements in the most objective and quantitative method. METHODS: Clinical and kinematic data were collected from thirty individuals using a universal plastic goniometer and a ten camera motion analysis system. Passive hip rotation range was obtained three trials for left and right hip joints using two measure methods simultaneously. RESULTS: There were significant differences between all matching measures of the two measures of internal and external rotation of the hip joint (p<.05). The relationship between the two tests for all measurements of the internal and external rotation of the hip was statistically significant with correlation coefficient form r=.87 to .96. (p<.01). CONCLUSION: Clinical measurement of the internal and external rotation of the hip using a universal plastic goniometer is effective to assess the hip condition. However, application of universal plastic goniometer requires careful attention in more accurate evaluation and research verification of the internal and external rotation of hip joint.

• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 2000년도 봄 학술발표회 논문집
• /
• pp.433-439
• /
• 2000

Reinforced concrete beams show increased ductile behavior when the compressive concrete is confined with transverse steel. In the inelastic range, the most variations of ductile behaviour are defined the equivalent length of the plastic hinge and the plastic hinge rotation. In an investigation to study the influence of such confinement, sixteen reinforced concrete beams were tested in flexure and the deflections noted at all stages of loading. For all the beams tested, the plastic hinge rotation have been computed and the effect of confinement on the same examined. The conclusions are summarized as follows: The equivalent lengths of the plastic hinge are ranged within the effective depth comparatively. The ability of the plastic hinge rotation of the reinforced concrete beams confined with transverse steel are enlarged when transverse reinforcement content are increased, but the spaces are more important as the shear force are largely increased.

• Archives of Reconstructive Microsurgery
• /
• 제16권1호
• /
• pp.23-29
• /
• 2007

The reconstruction of deep soft tissue defect such as pressure sore has difficult problems. Myocutaneous flaps have been used commonly as the best coverage method for pressure sore. But, they have several drawbacks such as sacrifice of functional muscle, high morbidity of the donor sites and bulkiness at the recipient site. The concepts of perforator flap has recently developed and widely used to overcome these disadvantages. Between March 2005 to July 2006, we have treated 9 patients who had pressure sore using perforator based fasciocutaneous island rotation flap. Preoperative unidirectional Doppler was used in all cases. Mean number of perforator vessels was 3.8 and flap sizes were from $7{\times}5\;cm$ to $14{\times}13\;cm$. Rotation angles of flap were from 90 degree to 180 degree. In all cases, donor sites were closed primarily. All flap survived completely and postoperative complications were wound dehiscence in 1 case, wound infection in 3 cases. The mean postoperative follow up period was 15.7 months and recurrence was not reported. We could decrease donor site morbidity and cover wound sites easily by using flap rotation and get robust blood supply without sacrifice of functional muscle. Fasciocutaneous perforator island rotation flap would be very useful for various pressure sore treatment.

• Archives of Plastic Surgery
• /
• 제49권1호
• /
• pp.39-42
• /
• 2022

Bilateral pectoralis major myocutaneous (PMMC) flaps are commonly used to reconstruct large chest wall defects. We report a case of large chest wall defect reconstruction using bilateral PMMC flaps augmented with axillary V-Y advancement rotation flaps for additional flap advancement. A 74-year-old male patient was operated on for recurrent glottic squamous cell carcinoma. Excision of the tumor resulted in a 10×10 cm defect in the anterior chest wall. Bilateral PMMC flaps were raised to cover the chest wall defect. For further flap advancement, V-Y rotation advancement flaps from both axillae were added to allow complete closure. All flaps survived completely, and postoperative shoulder abduction was not limited (100° on the right side and 92° on the left). Age-related skin redundancy in the axillae enabled the use of V-Y rotation advancement flaps without limitation of shoulder motion. Bilateral PMMC advancement flaps and the additional use of V-Y rotation advancement flaps from both axillae may be a useful reconstructive option for very large chest wall defects in older patients.

• 한국강구조학회 논문집
• /
• 제23권4호
• /
• pp.405-415
• /
• 2011

건축물의 안전한 내진설계를 위해서는 층간변위비 뿐만 아니라 부재에 요구되는 소성변형을 평가하여야 한다. 본 연구에서는 복잡한 비선형해석 없이 탄성해석을 사용하여 강기둥-약보로 설계된 철골 특수모멘트골조의 보에 요구되는 소성변형을 평가하는 간편한 방법을 개발하였다. 개발한 방법은 탄성해석 결과를 근거로 모멘트 재분배, 기둥 단면치수 및 보 소성힌지 이동, 패널존 변형, 중력하중, 변형경화 거동 등을 고려하여 보의 소성변형각을 직접적으로 예측한다. 또한 가새골조 또는 코어벽 등 횡력 저항구조와 모멘트골조의 상호 작용인 로킹 효과 고려한다. 검증을 위하여 강기둥-약보로 설계된 6층 특수모멘트골조에 제안된 방법을 적용하여 보의 소성변형각을 예측하고, 그 결과를 비선형 해석 결과와 비교하였다. 검증 결과, 제안된 방법은 설계 변수에 따른 보의 소성변형각을 합리적으로 예측하는 것으로 나타났다.

• 콘크리트학회논문집
• /
• 제22권6호
• /
• pp.825-832
• /
• 2010

철근콘크리트 구조물은 위험 단면이 휨강도에 도달하더라도 이 단면에서 소성힌지가 형성되어 휨모멘트가 재분배되어 곧바로 파괴에 도달하지 않는다. 이러한 소성힌지 영역에서 발생하는 비탄성 변형에 의해 소성 회전이 발생한다. 소성힌지길이는 주로 재료 특성에 영향을 받는다. 이 연구에서는 유로코드2에서 제시하고 있는 재료 모델로부터 산정된 휨곡률 분포로부터 소성힌지길이와 소성회전각을 일관되게 산정하였다. 재료 모델의 한계값 즉, 콘크리트 극한변형률, 철근 극한변형률 및 철근의 경화비(k)가 소성회전능력에 미치는 영향을 분석하였다. 해석 결과 콘크리트 극한변형률 및 철근 극한변형률이 증가함에 따라 소성회전능력이 증가하였고 특히, 철근의 경화비(k)가 증가함에 따라 소성 회전각은 크게 증가되는 것으로 나타났다. 따라서 각 재료 모델의 한계값 결정에 세심한 주의가 필요할 것으로 나타났다.

• 한국강구조학회 논문집
• /
• 제20권5호
• /
• pp.617-624
• /
• 2008

잘 설계된 철골 모멘트 접합부의 경우, 유효회전능력에 도달하기 전에 국부좌굴이 발생하고 비탄성 후좌굴 변형이 접합부 회전능력을 정의하는데 중대한 역할을 한다. 이 연구에서는 국부좌굴로 인한 강도저하와 보 소성힌지의 회전을 모델링하여, 단조증가하중 및 반복하중이 작 용하는 특별철골모멘트골조의 강접합 보-기둥 접합부의 회전능력을 예측하기 위한 근사적 해석모델을 제안한다. 제안된 항복선 소성힌지 모델은 좌굴된 소성힌지부의 형상에 기초하여 항복선과 소성존으로 구성되고, 소성메커니즘을 통해 국부좌굴후의 거동까지 포함한 모멘트-회전각 관계를 제 공한다. 향상된 WUF-W 와 RBS 접합부를 위해 제안된 모델을 개발한 후 실험결과와 비교를 통해 검증하였다. 동반논문(변수연구)에서는 광범위 한 H-형강의 기하학적 변수 따른 접합부 회전능력에 대하여 논의하였다.

• Archives of Plastic Surgery
• /
• 제33권2호
• /
• pp.181-186
• /
• 2006

Myocutaneous flaps have improved the management of soft tissue defects on buttocks and lower extremity. However, there are several inherent disadvantages of muscle flaps such as functional deficits of the donor sites and the bulkiness at the recipient site. To overcome these disadvantages, we have used perforator-based fasciocutaneous rotation flaps for reconstruction of the buttock and lower extremity defects. From March 2003 to February 2005, we have treated 14 patients using perforator-based fasciocutaneous rotation flaps. 10 flaps were based on perforators of the gluteus maximus muscle, and 4 flaps were nourished by perforators from the tibialis anterior and posterior system. The mean postoperative follow-up period was about 1 year. The technique involves localization of the flap perforators preoperatively with a Doppler. The flaps were elevated superficial to the fascia with preservation of one to three perforators. The donor site is then closed primarily. All flaps completely survived and there was no perioperative complications. There was no functional disability of the donor area with esthetically pleasing results. Perforator-based fasciocutaneous rotation flaps for the reconstruction of buttock and lower extremity defects are excellent alternatives to musculocutaeous flaps. The vascularity of the flaps is robust and dissection is technically easy. Perforator flaps do not require sacrificing muscles, but provide sufficient volume and are durable Furthermore, these flaps result in less scar formation and allow more liberal dissection with safety. We conclude that perforator-based fasciocutaneous rotation flaps are very useful for reconstruction of the buttock and lower extremity.

• Archives of Plastic Surgery
• /
• 제39권3호
• /
• pp.244-248
• /
• 2012

Many types of upper lip reconstruction have been introduced to treat defects after a tumor excision or trauma. The authors treated two cases of upper lip defects. A 35-year-old woman presented with a squamous cell carcinoma of the left upper lip that had invaded the corner of the mouth. After resecting the tumor, the defect was $3.7{\times}3.5cm$ in size. A 52-year-old woman presented with a dog bite of the right upper lip. The defect measured $4.0{\times}2.2cm$ in size. The two cases were reconstructed by combined rotation and advancement of a cheek flap. This technique produced a good functional outcome that allowed for oral competence and created an opening of adequate size. A combination of rotation and an advancement flap can be used to treat upper lip defects in a single-stage procedure. This approach produces a good functional and cosmetic outcome.