• Proceedings of the Korean Society For Composite Materials Conference
• /
• 2002.05a
• /
• pp.143-146
• /
• 2002

Unsized AS-4 carbon fibers were etched by RF plasma and then coated via plasma polymerization in order to enhance adhesion to vinyl ester resin. The gases utilized for the plasma etching were Ar, $N_2 and O_2$, while the monomers used for the plasma polymerization coating were acetylene, butadiene and acrylonitrile. The conditions for the plasma etching and the plasma polymerization were optimized by measuring interfacial adhesion with vinyl ester resin via micro-droplet tests. Among the treatment conditions, the combination of Ar plasma etching and acetylene plasma polymerization provided greatly improved interfacial shear strength (IFSS) of 69MPa compared to 43MPa with as-received carbon fiber. Based on the SEM analysis of failure surface and load-displacement curve, it was assume that the failure might be occurred at the carbon fiber and plasma polymer coating. The plasma etched and plasma polymer coated carbon fibers were subjected to analysis with SEM, XPS, FT-IR or Alpha-Step, and dynamic contact angles and tensile strengths were also evaluated. Plasma polymer coatings did not change tensile strength and surface roughness of fibers, but decreased water contact angle except butadiene plasma polymer coating, possibly owing to the functional groups introduced, as evidenced by FT-IR and XPS.

• Proceedings of the Korean Society For Composite Materials Conference
• /
• 1999.11a
• /
• pp.36-39
• /
• 1999

Steel tire cords were coated via RF Plasma Polymerization of acetylene in order to enhance adhesion to rubber compounds. Adhesion of tire cords was measured by TACT as a function of plasma polymerization and argon etching conditions such as power, treatment time and chamber pressure. Tested tire cords were analysed by SEM to elucidate the adhesion mechanism. The highest adhesion values were obtained with argon etching condition at 90W, 10min, 30mtorr followed by acetylene plasma polymerization condition at 10W, 30sec., 30mtorr. In SEM analysis, the plasma polymerized tire cord at the optimized condition showed 100% rubber coverage as observed from brass-plated steel tire cords.

• The Transactions of the Korean Institute of Electrical Engineers
• /
• v.45 no.3
• /
• pp.438-443
• /
• 1996

The effect of plasma polymerization conditions on the structure of the plasma polymerized styrene were investigated by using Fourier Transform Infrared Ray(FT-IR), Differential Scanning Calorimetry (DSC), Gel Permeation Chromatography(GPC). Plasma polymerized thin film was prepared using an interelectrode inductively coupled gas-flow-type reactor. We show that polymerization parameters of thin film affect sensitivity and etching resistance of plasma polymerized styrene is 1.41~3.93, and deposition rate of that are 32~383[.angs./min] with discharge power. Swelling and etching resistance becomes more improved with increasing discharge power during plasma polymerization. (author). 11 refs., 10 figs., 1 tab.

• Electrical & Electronic Materials
• /
• v.7 no.5
• /
• pp.425-429
• /
• 1994

In this paper, we study on the plasma polymerized styrene as a negative electron-beam resist. Plasma polymerized thin film was prepared using an interelectrode inductively coupled gas-flow type reactor. We show that polymerization parameters of thin film affect sensitivity and etching resistance of the resist. Molecular weight distribution of plasma polymerized styrene is 1.41-3.93, and deposition rates of that are 32-383[.angs./min] with discharge power. Swelling and etching resistance becomes . more improved with increasing discharge power during plasma polymerization. Etch rate by RIE is higher than that by plasma etching.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 1998.06a
• /
• pp.131-134
• /
• 1998

This work was carried out to develop a pattern on the nanometer scale using plasma polymerization and plasma etching. This study is also aimed at developing a resist for the nano process and a vacuum lithography process. The thin films of plasma polymerization were fabricated by the plasma po1ymerization of inter-electrode capacitively coupled gas flow system. After delineating the pattern at accelerating voltage of 30[kV]. ranging the dose of 1∼500[${\mu}$C/$\textrm{cm}^2$], the pattern was developed with dry tree and formed by plasma etching. By analysing of the molecule structure using FT-lR, it was confirmed that the thin films of PPMST contains the functional radicals of the MST monomer. The thin films of PPMST had a highly crosslinked structure resulting in a higher molecule weight than the conventional resist.

• The Transactions of the Korean Institute of Electrical Engineers
• /
• v.43 no.5
• /
• pp.802-808
• /
• 1994

The purpose of this paper is to describe an application of plasma polymerized thin film as an electron beam resist. Plasma polymerized thin film was prepared using an interelectrode capacitively coupled gas-flow-type reactor, and chosen methylmethacrylate(MMA)and methylmethacrylate-tetrameth-yltin(MMA-TMT) as a monomer. This thin films were also delineated by the electron-beam apparatus with an acceleration voltage of 30kV and an expose dose ranging from 20 to 900$\mu$C/cmS02T. The delineated pattern in the resist was developed with the same reactor which is used for polymerization using an argon as etching gas. The growth rate and etching rate of the thin film is increased with increasing of discharge power. Thin films by plasma polymerization show polymerization rate of 30~45($\pm$3) A/min, and etching rate of 440($\pm$30) A/min during Ar plasma etching at discharge power of 100W. In apparently lower than that of conventional PMMA, but the plasma-etching rate of PP(MMA-TMT) was higher than that of PPMMA.

• Elastomers and Composites
• /
• v.35 no.1
• /
• pp.63-70
• /
• 2000

Zinc plated steel tire cords were subjected to RF plasma etching of argon, followed by plasma polymerization coating of acetylene or butadiene in order to enhance adhesion to rubber compounds. Plasma polymerization was carried out under optimized conditions of 10 W, 30 sec, 30 mTorr for acetylene and butadiene gas, while plasma etching was performed at 90W, 10min and 30mTorr. The adhesion of tire cords was evaluated via Tire Cords Adhesion Test (TCAT) and the failure surfaces of the tested samples were analyzed by SEM. Polymer coating by plasma polymerization was also characterized by FT-IR, Alpha-Step and dynamic contact angle analyzer in order to elucidate the adhesion mechanism.

• Journal of Adhesion and Interface
• /
• v.4 no.1
• /
• pp.28-34
• /
• 2003

Steel tire cords were subjected to plasma polymerization coating of acetylene in order to enhance the adhesion to rubber compounds. Plasma polymerization coating was varied to plasma polymerization coating of acetylene, argon plasma etching+plasma polymerization, or argon plasma. etching+plasma polymerization with Ar carrier gas. Adhesion was evaluated via TCAT samples and compared to those with brass coated tire cord. For durability study, plasma polymer cooled tire cords were aged in lab atmosphere for 1, 3, 5, 10 or 15 days, while TCAT specimens prepared with plasma polymer coated tire cords were aged in distilled water, 10% NaCl solution or $100^{\circ}C$ oven for 1, 2, 3 or 4 weeks. After testing, failure surfaces were analyzed with SEM/EDX. Among the treatments, the highest adhesion was obtained by Ar etching+acetylene plasma. polymerization coating with Ar carrier gas, providing almost same pull-out force as the brass coated tire cords. Upon the aging of the tire cords in the lab atmosphere, brass coated tire cords provided better adhesion than plasma polymer coated tire cords, while the TCAT samples with plasma polymer coated tire cords exhibited similar or slightly superior durability to those with brass coated tire cords.

• Elastomers and Composites
• /
• v.35 no.1
• /
• pp.53-62
• /
• 2000

Zinc plated steel tire cords were treated with RF plasma polymerization coating of acetylene or butadiene in order to enhance adhesion to rubber compounds. Plasma polymerization was carried out as a function of plasma power, treatment tune and gas pressure. In order to maximize adhesion, argon plasma etching was performed, with carrier gas such as argon, nitrogen and oxygen, while the adhesion of tire cords was evaluated via TCAT. Best results were obtained from a combination treatment of argon etching (90 W. 10 min, 30 mTorr) and acetylene plasma polymerization coating (10 W, 30 sec, 30 mTorr) with argon carrier gas (25/5:acetylene/argon). These samples exhibited a pull out force of 285N which is comparable to that obtained from the brass plated tire cords (290N).

• Proceedings of the KIEE Conference
• /
• 1998.07d
• /
• pp.1343-1345
• /
• 1998

This work was carried out to develop a pattern on the nanometer scale using plasma polymerization and plasma etching. This study is also aimed at developing a resist for the nano process and a vacuum lithography process. The thin films of plasma polymerization were fabricated by the plasma polymerization of inter-electrode capacitively coupled gas flow system. After delineating the pattern at accelerating voltage of 30[kV], ranging the dose of $1-500[{\mu}C/cm^2$], the pattern was developed with dry type and formed by plasma etching.