• Journal of Radiation Protection and Research
• /
• v.22 no.2
• /
• pp.103-109
• /
• 1997

Adult male rats were exposed to a whole body with a single dose of 1.0, 2.0, 3.0, 5.0, and 7.0 Gy. The animals were sacrificed 48, 72, 96 and 216 hours following exposure. A competitive enzyme linked immunosorbent assay(ELISA) with antigen immobilized on the solid phase has been developed to measure ceruloplasmin in rat serum and complete dose response curves. Ceruloplasmin was purified from the plasma of turpentine treated male rats. Coating of ceruloplasmin had more effectiveness in 10 mM Tris-HCI, 150 mM sodium chloride, pH 7.4 than in 50 mM carbonate/bicarbonate buffer, pH 9.6. The coating range for ceruloplasmin was $70{\sim}140ng$/well. Levels of ceruloplasmin increased to maximum on the $72{\sim}96$ hours after irradiation. Slope of between response and dose was greatest value 96 hours following irradiation. Normal ceruloplasmin levels were not recorded 216 hours following exposure. In 0.1 Gy irradiated group, levels of ceruloplasmin also increased to maximum on the $72{\sim}96$ hours following irradiation. The concentration of this protein remained significantly different from control value, 196 hours after exposure. Ceruloplasmin was identified as one of the major acute phase protein following irradiation and further studies about gene expression and regulation would be necessary for radiation protection.

• Korean Chemical Engineering Research
• /
• v.47 no.2
• /
• pp.150-156
• /
• 2009

Plasma Display Panels(PDPs) require to have improved luminous efficiency, low manufacturing cost, and high image quality to compete with other flat display devices such as Liquid Crystal Displays(LCDs) and organic light-emitting diodes(OLEDs). In addition, the diversity of product line-up may be needed for high market share. In this paper, the optical characteristics of typical green phosphor for PDP application are reviewed and the problem-based solution will be proposed. We also shortly describe the principle of 3D-PDPs which are promising. Then, the requirement of green phosphor for 3D-PDP application is summarized and research achievement, as of now, is described. The typical problems of $Zn_2SiO_4:Mn$ phosphor, which is the most well-known, are the negatively charged surface property and the long decay time, which leads to unstable discharge in green cell and afterimage. These problems were solved by coating the phosphor surface with metallic oxide. It was found that $Al_2O_3$ would be the best material for $Zn_2SiO_4:Mn$ phosphor. It gives longevity as well as low operating voltage due to the charging effect in green cells. Also, new phosphors, $(Y,\;Gd)Al_3(BO_3)_4:Tb$ and $(Mg,\;Zn)Al_2O_4:Mn$ phosphor are proposed for increasing the luminance and reducing the decay time, which are capable to apply for 3D-PDP application.

• Journal of the Korean institute of surface engineering
• /
• v.46 no.2
• /
• pp.68-74
• /
• 2013

For the coating of diamond films on WC-Co tools, a buffer interlayer is needed because Co catalyzes diamond into graphite. W and Ti were chosen as candidate interlayer materials to prevent the diffusion of Co during diamond deposition. W or Ti interlayer of $1{\mu}m$ thickness was deposited on WC-Co substrate under Ar in a DC magnetron sputter. After seeding treatment of the interlayer-deposited specimens in an ultrasonic bath containing nanometer diamond powders, $2{\mu}m$ thick nanocrystalline diamond (NCD) films were deposited at $600^{\circ}C$ over the metal layers in a 2.45 GHz microwave plasma CVD system. The cross-sectional morphology of films was observed by FESEM. X-ray diffraction and visual Raman spectroscopy were used to confirm the NCD crystal structure. Micro hardness was measured by nano-indenter. The coefficient of friction (COF) was measured by tribology test using ball on disk method. After tribology test, wear tracks were examined by optical microscope and alpha step profiler. Rockwell C indentation test was performed to characterize the adhesion between films and substrate. Ti and W were found good interlayer materials to act as Co diffusion barriers and diamond nucleation layers. The COFs on NCD films with W or Ti interlayer were measured as less than 0.1 whereas that on bare WC-Co was 0.6~1.0. However, W interlayer exhibited better results than Ti in terms of the adhesion to WC-Co substrate and to NCD film. This result is believed to be due to smaller difference in the coefficients of thermal expansion of the related films in the case of W interlayer than Ti one. By varying the thickness of W interlayer as 1, 2, and $4{\mu}m$ with a fixed $2{\mu}m$ thick NCD film, no difference in COF and wear behavior but a significant change in adhesion was observed. It was shown that the thicker the interlayer, the stronger the adhesion. It is suggested that thicker W interlayer is more effective in relieving the residual stress of NCD film during cooling after deposition and results in stronger adhesion.

• Proceedings of the Materials Research Society of Korea Conference
• /
• 2009.11a
• /
• pp.49.1-49.1
• /
• 2009

산업화 이후, 석탄 석유를 중심으로 한 화석연료가 이산화탄소를대량으로 배출하며 지구 온난화를 야기함에 따라, 석유를 대체할 새로운 에너지원에 대한 관심이 높아지고 있다. 많은 대체에너지 가운데, 청정하고 무한 재생 가능한대체에너지를 이야기할 때, 가장 큰 기대를 받고 있는 것은 태양에너지이며, 이에 보조를 맞춰 태양광 발전에 대한 연구개발이 국내외적으로 활발히 진행되고 있는 실정이다. 태양 전지는 빛 에너지를 직접 전기 에너지로 바꿔주는 소자로, 셀의효율을 높이기 위해서는 최대한 많은 빛을 흡수시킬 수 있는 것이 중요하다. 빛의 반사를 줄이는 방법에는 Texturing 과 Antireflecting coating 이있다. Antireflecting coating은 반도체와 공기의 중간 굴절율을 갖는 박막을 증착하여 측면 반사를 감소시킴으로서 빛의 손실을 감소시키는 역활을 한다. 반사 방지막으로 쓰이는 SiNx는 SiOx의 대체 물질로 굴절률이 약 1.5로서 Si에 쉽게 형성시킬 수 있고, texturing된 Si 표면에 적합하며 반사율을 10 %에서 2 %로 줄일 수 있다. 나아가 고성능의 반사방지막은 박막의 균일도확보 및 passivation 공정이 필수적이라 판단된다. 따라서 본 연구에서는 PECVD 방법으로 SiH4와 NH3 gas 의 비율을 변화시켜 증착한 SiNx 박막의 결정학적 특성을 X-ray Diffraction 분석과 TEM (TransmissionElectron Microsopy) 을 통해 관찰하였으며, XPS (X-rayphotoelectron spectroscopy) 를 통해 화학적결합을 확인하였고, 이를 FT-IR (Fourier Transform-Infrared spectroscopy)를 통해 관찰한 결과와 연관시켜분석하였다. 굴절율의 경우 Ellipsometry를 이용하여측정하였으며 위의 측정을 통하여 SiNx박막의 반사 방지막으로써의 가능성을 확인하였다.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.59 no.4
• /
• pp.743-748
• /
• 2010

Boron nitride (BN) and carbon nitride (CN) films, which have relatively low work functions and commonly exhibit negative electron affinity behaviors, were coated on carbon nanotubes (CNTs) by magnetron sputtering. The CNTs were directly grown on metal-tip (tungsten, approximately 500nm in diameter at the summit part) substrates by inductively coupled plasma-chemical vapor deposition (ICP-CVD). The variations in the morphology and microstructure of CNTs due to coating of the BN and CN films were analyzed by field-emission scanning electron microscopy (FE-SEM). The energy dispersive x-ray (EDX) spectroscopy and Raman spectroscopy were used to identify the existence of the coated layers (CN and BN) on CNTs. The electron-emission properties of the BN-coated and CN-coated CNT-emitters were characterized using a high-vacuum field emission measurement system, in terms of their maximum emission currents ($I_{max}$) at 1kV and turn-on voltage ($V_{on}$) for approaching $1{\mu}A$. The results showed that the $I_{max}$ current was significantly increased and the $V_{on}$ voltage were remarkably reduced by the coating of CN or BN films. The measured values of $I_{max}-V_{on}$ were as follows; $176{\mu}A$-500V for the 5nm CN-coated emitter and $289{\mu}A$-540V for the 2nm BN-coated emitter, respectively, while the $I_{max}-V_{on}$ of the as-grown (i.e., uncoated) emitter was $134{\mu}A$-620V. In addition, the CNT emitters coated with thin CN or BN films also showed much better long-term (up to 25h) stability behaviors in electron emission, as compared with the conventional CNT emitter.

• Proceedings of the Materials Research Society of Korea Conference
• /
• 2003.03a
• /
• pp.200-200
• /
• 2003

고체산화물 연료전지(SOFC)에서 사용되는 연결재의 주 기능은 각 단위 셀의 연료극과 다음 셀의 공기극을 전기적으로 연결하여, 공기와 사용연료의 분리역할을 하기 위하여 사용된다. SOFC용 연결재는 다른 구성요소 소재보다, 높은 전자 전도성, 낮은 이온전도성, 우수한 기계 적강도가 요구되며, SOFC는 고온에서 작동되기 때문에, 상온에서 작동온도까지 다른 요소 소재들과 유사한 열팽창계수와 물리, 화학적으로 안정성이 요구된다. 현재 연결재 제조기술은 EVD, CVD, plasma spraying, tape casting 등 다양하게 연구되고 있으며, 본 연구는 세라믹 연결재 증착방법 중 저렴한 비용으로 대량 생산이 용이한 습식법(dip coaling)을 적용하여, 연료극 지지체식 flat-tube형 고체산화물 연료전지의 지지체를 위해 세라믹 연결재를 제조하고, 그 특성을 연구하였다. 세라믹 연결재로써 선정한 합성조성은 LaCr $O_3$에 Ca이 치환 고용된 L $a_{0.6}$C $a_{0.41}$Cr $O_3$으로 pechini법으로 합성하였다. 합성된 조성은 100$0^{\circ}C$에서 5시간 하소후 가속 Ball Milling하여 0.5$\mu\textrm{m}$의 평균입자크기를 얻을 수 있었다. XRD 상분석결과 perovskite상 (L $a_{1-x}$ Ca/x/Cr $O_3$)과 CaCr $O_4$를 얻을 수 있었다. slurry를 제조하여 막의 밀착성을 증진시키기 위해 sand blasting시킨 flat tube지지체에 진공펌프를 이용하여 소재내부와 외부의 압력차로 dip coating한 후, 140$0^{\circ}C$로 소결 하였다. coating 결과 박리현상은 없었으나, 표면과 단면의 SEM분석결과 다소 porous한 박막층이 형성되었으며, Ca이온이 지지체로 permeation되는 현상이 발생하였다. 이와 같은 결과로부터 보다 치밀한 박막생성을 위해, slurry 제조조건을 변화시켰으며, Ca이온의 migration을 막기 위해 barrier layer를 이용하였다 완전 소결된 지지체는 가스투과도와 전기전도도측정을 통하여 특성을 평가하였다.였다.다.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.28 no.2
• /
• pp.80-84
• /
• 2018

Mg alloys AZ31 and AZ91 were Plasma-Electrolytic-Oxidized in Na-P and Na-Si system electrolyte at various concentration, applied voltage and time. Thickness and surface roughness of PEO coating were examined. Salt spraying test were carried out to compare their corrosion resistances. Generally, corrosion resistances rate were increased as thickness and crystallinity increasing. Size of pore being larger, long term corrosion resistance decreased. It is turned out that $Mg_2SiO_4$ and other crystalline phase rather than MgO might be increase corrosion resistance dramatically.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.29 no.10
• /
• pp.665-670
• /
• 2016

Prevailing dissemination of machine tools and cutting technology have caused drastic developments of high speed dry machining with work materials of high hardness, and demands on the high-hardness-materials with high efficiency have become increasingly important in terms of productivity, cost reduction, as well as environment-friendly issue. Addition of Si to TiAlN has been known to form nano-composite coating with higher hardness of over 30 GPa and oxidation temperature over $1,000^{\circ}C$. However, it is not easy to add Si to TiAlN by using conventional PVD technologies. Therefore, Ti-Al-Si-N have been prepared by hybrid process of PVD with multiple target sources or PVD combined with PECVD of Si source gas. In this study, a single composite target of Ti-Al-Si was prepared by powder metallurgy of MA (mechanical alloying) and SPS (spark plasma sintering). Properties of he resulting alloying targets were examined. They revealed a microstructure with micro-sized grain of about $1{\sim}5{\mu}m$, and all the elements were distributed homogeneously in the alloying target. Hardness of the Ti-Al-Si-N target was about 1,127 Hv. Thin films of Ti-Al-Si-N were prepared by unbalanced magnetron sputtering method by using the home-made Ti-Al-Si alloying target. Composition of the resulting thin film of Ti-Al-Si-N was almost the same with that of the target. The thin film of Ti-Al-Si-N showed a hardness of 35 GPa and friction coefficient of 0.66.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2014.02a
• /
• pp.162-162
• /
• 2014

최근 들어 wearable computing에 대한 수요가 증가하면서 flexible device에 대한 연구가 활발히 진행되고 있다. 하지만, flexible device를 구현하기 위해서는 기판의 damage를 줄이기 위한 저온공정, device life-time 향상을 위한 passivation, 와이어 본딩 등 다양한 문제들이 해결 되어야 한다. 이러한 문제들 중, polymer 기판과 금속간의 접착력을 향상시키기 위해서 많은 연구자들은 기판의 표면에 adhesive layer를 도포하거나 금속잉크의 solvent를 변화시키는 등의 연구를 진행해왔다. 종래의 연구는 기존 device를 대체 할 수 있을 정도의 생산성과 polymer 기판에 대한 열 적인 손상 이 문제가 되었다. 종래의 문제를 해결하기 위하여 저온공정, in-line system이 가능한 준 준 대기압 플라즈마를 사용하였다. 본 연구에서는 금속잉크를 Ink-jet으로 jetting하여 와이어 본딩 하는 과정에서 전도성 ink의 선폭을 유지시키고 접착력을 향상하기 위하여 준 대기압 플라즈마 공정을 이용하여 이러한 문제점을 해결하고자 하였다. Polymer 기판 표면에 roughness를 만들기 위해 대략 수백 nm 크기를 갖는 graphene flake를 spray coating하여 마스크로 사용하고 준 대기압 플라즈마를 이용하여 표면을 식각 함으로써 roughness를 형성시켰다. 준 대기압 플라즈마를 발생시키기 위해 double discharge system에서 6 slm/1.5 slm (He/O2) gas composition을 하부 전극에 흘려보내고 60 kHz, 5 kV 파워를 인가하였다. 동시에 상부 전극에는 30 kHz, 5 kV 파워를 인가하여 110초 동안 표면 식각 공정을 진행하였다. Graphene flake mask가 coating되어 있는 유연기판을 산소 플라즈마 처리 한 후 물에 3초 동안 세척하여 표면에 남아있는 graphene flake를 제거하고 6 slm/0.3 slm (He/SF6)의 유량으로 주파수와 파워 모두 동일 조건으로 110초 동안 표면 처리를 하였다. Figure 1은 표면 개질 과정과 graphene flake를 mask로 사용하여 얻은 roughness 결과를 SEM을 이용하여 관찰한 결과이다. 이와 같이 실험한 결과 ink와 기판간의 접촉면적을 늘려주고 접촉 각을 조절하여 Wenzel model 을 형성 할 수 있는 표면 roughness를 생성하였고 표면의 화학적 결합을 C-F group으로 치환하여 표면의 물과 접촉각 이 $47^{\circ}$에서 $130^{\circ}$로 증가하는 것을 확인하였다.

• Proceedings of the Korean Institute of Surface Engineering Conference
• /
• 2017.05a
• /
• pp.153-153
• /
• 2017

The application of the coating supports the mechanical characteristics of the implant, and various materials and coatings are currently being used in the implant in a way to accelerate adhesion. Especially, plasma electrolytic oxidation (PEO) coating has been proposed continually with good surface treatment of titanium alloys. Also, the PEO process can incorporate Ca and P ions on the titanium surface through variables varied factor. PEO process for bioactive surface has carried out in electrolytes containing Ca and P ions. Natural bone is composed of mineral elements such as Mg, Si, Zn, Sr, and Mn, etc. Especially, Mg and Si of these elements play role in bone formation and growth after clinical implantation of bio-implants. In this study, corrosion charateristics of PEO-treated Ti-6Al-4V alloy in solution containing Si and Mg ions has been investigated using several experimental techniques. The PEO-treated surfaces were identified by X-ray diffraction, using a diffractometer (XRD, Philips X' pert PRO, Netherlands) with Cu $K{\alpha}$ radiation. The morphology was observed by field-emission scanning electron microscopy (FE-SEM, Hitachi 4800, Japan) and energy-dispersive X-ray spectroscopy (EDX, Oxford ISIS 310, England). The potentiodynamic polarization and AC impedance tests for electrochemical degradations were carried out in 0.9% NaCl solution at similar body temperature using a potentiostat with a scan rate of 1.67mV/s and potential range from -1500mV to + 2000mV.