• Transactions of the Korean Society of Automotive Engineers
• /
• v.2 no.1
• /
• pp.73-83
• /
• 1994

Press formabilities of aluminum sheets for automobile body were investigated. Plane strain stretching test (called RIST-PSST), cupping test and U bending test were performed to assess the press formability of aluminum sheets respectively. The results showed that aluminum sheets are generally inferior to cold-rolled steel sheet of deep drawing quality (CSP3N) in press formability. The limiting punch height (LPH) and limiting plane strain (FLCo) of aluminum sheets are 50%-70% level compared to that of CSP3N. Moreover, the limiting drawing ratios(LDR) of aluminum sheets are ranged between 1.95 and 2.1. The poor press formability of aluminum sheets is responsible for low values of total elongation and plastic anisotropy parameter in tensile characteristic. The shape fixability of aluminum sheets evaluated in U bending test is very poor due to its low elastic modulus compared to CSP3N.

• Magazine of the Korean Society of Agricultural Engineers
• /
• v.41 no.2
• /
• pp.70-79
• /
• 1999

The lower ground of structure, in which the strip loads, such as earth dams and embankments , are signiificantly working on , is required to be interpreted as a state of plane strain where the strain of intermediated principal stress direction is put '0' . The plane strain state is frquently observed in actural soil engineering case. For those case, drained stress-strain and strength behavior of Iksan weathered granite soil prepared in cubical specimens with cross-anisotropic fabric was studied by conventional triaxial compression, plane strain and cubial triaxial tests with independent control of the three principal stress. All specimens were loaded under conditions of principl stress directions fixed and aligned with the directions of the material axes. As a result of research , when a ground condition is analyzed under plane strain state, the shear strength obtained from the conventional triaxial compression test can be understimated.

• Journal of the korean Society of Automotive Engineers
• /
• v.14 no.6
• /
• pp.9-22
• /
• 1992

본 글에서는 판재의 스탬핑 성형성 평가를 위해 소재 제조업체와 자동차업체에서 널리 사용되고 있는 2,3개의 대표적인 모사실험과 평면변형장출실험을 소개하고 각각의 특징들에 대하여 논하고자 한다. 1. 딥 드로잉실험(deep drawing test after swift). 2. 돔 장출실험(dome punch stretching test). 3. 평면변형인장실험(plane strain tension test). 4. 평면변형장출실험(plane strain punch stretching test)

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 1997.03a
• /
• pp.15-18
• /
• 1997

The plane strain stretch test (PSST) developed by POSCO as an activity of customer service was applied to the establishment of the formability criteria and the prediction of failure during the stamping processes. The PSST was applied to the actual parts such as oil pan and shock mount and the criteria of PSST value for each forming parts were established. These value can provide the possibility of prediction of failure before the stamping process. These results show that the PSST can precisely predict the stamping formability of steel sheets.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2005.11a
• /
• pp.727-730
• /
• 2005

Cellulose based Electro-Active Papers (EAPap) is very promising material due to its merits in terms of large bending deformation, low actuation voltage, ultra-lightweight, and biodegradability. These advantages make it possible to utilize applications, such as artificial muscles and achieving flapping wings, micro-insect robots and smart wall papers. This paper investigates the in-plane strains of EAPap under electric fields, which are useful for a contractile actuator application The preparation of EAPap samples and the in-plane strain measurement system are explained, and the test results are shown in terms of electric field, frequency and the oriental ions of the samples. The power consumption and the strain energy of EAPap samples are discussed. Although there are still unknown facts in EAPap material, this in-plane strain may be useful for artificial muscle applications.

• Journal of the Korean Geotechnical Society
• /
• v.22 no.1
• /
• pp.5-14
• /
• 2006

A simple and useful plane strain testing device was newly developed and its mechanical features were presented in this paper. The new testing device was designed to be capable of testing various stress paths expected under plane strain condition with only the conventional triaxial loading system. The applicability of the new testing device was systematically checked both by theoretical evaluation and by experiments. As a result, it was found that the new testing device has much wider range of application than the conventional plane strain testing devices.

• Structural Engineering and Mechanics
• /
• v.38 no.3
• /
• pp.333-347
• /
• 2011

This paper shows the solution for an orthotropic disk under the plane strain condition obtained with complex stress functions. These stress functions were induced by Lekhnitskii and expanded by one of the authors. Regarding diametrical compression test, the finite element method poses difficulties in representing the concentrated force because the specimens must be divided into finite elements during calculation. On the other hand, the method shown in this study can exactly represent this force. Some numerical results are shown and compared with those obtained under the plane stress condition for both stress and displacement. This comparison shows that the differences between the tensile stresses occurred under the plane strain condition and also that the differences under a plane stress condition increase as the orthotropy ratio increases for some cases.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2007.11a
• /
• pp.194-197
• /
• 2007

The dome stretching and tension test have been made to obtain a forming limit curve(FLC) for the copper alloy which is used for manufacturing the regenerative cooling chamber. For experimental survey of the forming limit curve, we have used in-plane tension specimen to obtain tension-compression strain state and also out of plane specimen to obtain tension-tension strain state through dome stretching test. All specimens are divided into longitudinal and radial direction specimens by the manufacturing method. The test results shows that in tension-tension region, copper alloy possesses a maximum major strain of 62.3% and maximum minor strain of 58.6%. In the tension-compression region, maximum major strain is 60.5% and maximum minor strain is 25.8%.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 1997.10a
• /
• pp.158-163
• /
• 1997

In this paper the tool geometry of the PSS test were optimized in order to assure the reliability of the test. Considering many factors for optimization of the tool geometry, computer-simulation technique using three-dimensional finite element method(FEM) was used. Three design variables -the punch length, punch crown and punch corner radius- are chosen to be optimized according to the Taguchi's experiment technique with the L9 orthogonal array. The optimum condition to ensure the plane strain mode over the overall area of the specimen was clarified. Moreover the simulation results are confirmed by experiment.

• Geomechanics and Engineering
• /
• v.5 no.6
• /
• pp.499-517
• /
• 2013

In order to investigate shear behavior of granular materials due to excavation and associated unloading actions, load-controlled plane strain compression tests under decreasing confining pressure were performed under drained conditions and the results were compared with the conventional plane strain compression tests. Four types of granular material consisting of two quartz sands and two glass beads were used to investigate particle shape effects. It is clarified that macro stress-strain behavior is more easily influenced by stress level and stress path in sands than in glass beads. Development of localized deformation was analyzed using photogrammetry method. It was found that shear bands are generated before peak strength and shear band patterns vary during the whole shearing process. Under the same test condition, shear band thickness in the two sands was smaller than that in one type of glass beads even if the materials have almost the same mean particle size. Shear band thickness also decreased with increase of confining pressure regardless of particle shape or size. Local maximum shear strain inside shear band grew approximately linearly with global axial strain from onset of shear band to the end of softening. The growth rate is found related to shear band thickness. The wider shear band, the relatively lower the growth rate. Finally, observed shear band inclination angles were compared with classical Coulomb and Roscoe solutions and different results were found for sands and glass beads.