• Korean Journal of Environment and Ecology
• /
• v.32 no.3
• /
• pp.303-312
• /
• 2018

This study was conducted to investigate the relationship between the decrease of forest biomass by forest thinning and the change of temperature in the natural forest by measuring forest biomass and temperature before and after forest thinning in the Pusan National University forest where afforestation had been carried out. We intended to investigate the relationship between the forest biomass, estimated by calculating the Basal area, Crown area and Crown volume using the same formula to the same quadrat before and after forest thinning, and the forest temperature. Temperature measurement was carried out on April 20, 2016 through 28 before forest thinning, July 26, 2016 through November 4 around the time of forest thinning, and April 15, 2017 through May 8 after forest thinning. A temperature data logger was installed to point north at the height of 2.0 m above the ground in the center of the quadrat to record data every 10 minutes during the measurement periods. We used the AWS (Automatic Weather Station) data of the Dongnae-gu area located in the nearby city because it was difficult to set the control group since the whole forest was the subject to the forest thinning. The analysis of the relationship between forest biomass change and temperature showed that the change in temperature inside the forest was the greatest in the midday (12:00 - 15: 00) and was highly correlated with the Crown volume in the forest biomass. The temperature increase was much larger (average $1.91^{\circ}C$) 1 year after forest thinning than immediately after forest thinning (average $0.74^{\circ}C$). The comparison of the decrease rate of Crown volume and the increase in temperature showed that the Pitch pine community, which showed the highest decrease of Crown volume by 15.4%, recorded the highest temperature rise of $1.06^{\circ}C$ immediately after forest thinning and $2.49^{\circ}C$ 1 year after forest thinning. The Pitch pine-Korean red pine community, which showed the lowest Crown volume reduction rates with 5.0%, recorded no significant difference immediately after forest thinning but a temperature rise of $0.92^{\circ}C$ 1 year after forest thinning. The results confirmed that the decrease of forest biomass caused by forest thinning led to a rapid increase of the internal temperature. The fact that the temperature increase was more severe after 1 year than immediately after forest thinning confirmed that the microclimate changes due to the removed biomass cannot be recovered in a short time.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.9 no.1
• /
• pp.16-22
• /
• 2008

We fabricated thermally-evaporated 10 nm-Ni/30 nm and 70 nm Poly-Si/200 nm-$SiO_2/Si$ structures to investigate the thermal stability of nickel silicides formed by rapid thermal annealing(RTA) of the temperature of $300{\sim}1100^{\circ}C$ for 40 seconds. We employed for a four-point tester, field emission scanning electron microscope(FE-SEM), transmission electron microscope(TEM), high resolution X-ray diffraction(HRIXRD), and scanning probe microscope(SPM) in order to examine the sheet resistance, in-plane microstructure, cross-sectional microstructure evolution, phase transformation, and surface roughness, respectively. The silicide on 30 nm polysilicon substrate was stable at temperature up to $900^{\circ}C$, while the one on 70 nm substrate showed the conventional $NiSi_2$ transformation temperature of $700^{\circ}C$. The HRXRD result also supported the existence of NiSi-phase up to $900^{\circ}C$ for the Ni silicide on the 30 nm polysilicon substrate. FE-SEM and TEM confirmed that 40 nm thick uniform silicide layer and island-like agglomerated silicide phase of $1{\mu}m$ pitch without residual polysilicon were formed on 30 nm polysilicon substrate at $700^{\circ}C\;and\;1000^{\circ}C$, respectively. All silicides were nonuniform and formed on top of the residual polysilicon for 70 nm polysilicon substrates. Through SPM analysis, we confirmed the surface roughness was below 17 nm, which implied the advantage on FUSI gate of CMOS process. Our results imply that we may tune the thermal stability of nickel monosilicide by reducing the height of polysilicon gate.

• Journal of Korean Society of Environmental Engineers
• /
• v.31 no.11
• /
• pp.1025-1032
• /
• 2009

This study investigated a possibility to develop an adsorption process for volatile organic compounds (VOCs) of the solvent emitted during dry cleaning. Pitch activated carbon fiber (ACF) was chosen as an adsorbent of VOCs, and an electric swing adsorption process was utilized for the reproduction of the adsorbent after the completion of VOCs adsorption. Effects of ACF types and several solvents such as trichloroethylene (TCE) and toluene were examined on breakthrough curves and amounts of adsorbed VOCs. ACF was pretreated under various conditions in order to enhance the amounts of the adsorbed VOCs. Temperatures and voltages were measured for the reproduction of the ACF after full adsorption. ACF having micropores exhibited high adsorption of TCE, and high surface area of ACF could increase the adsorption property of toluene. In general, ACF could adsorb 41~54% TCE of the adsorbent weight. The increase of inlet VOCs concentration significantly decreased the breakthrough time and slightly lowered the amounts of adsorbed VOCs. Thus, ACF could effectively adsorb VOCs in low concentration in the feed stream. ACF pretreated by heat under vacuum showed excellent toluene adsorption with controlling oxygen functional groups on the ACF surface, which revealed that vacant carbon site could be the adsorption point of toluene. Most adsorbed toluene was desorbed at $150^{\circ}C$.

• Journal of the Society of Naval Architects of Korea
• /
• v.41 no.6
• /
• pp.120-125
• /
• 2004

There are very few numbers of 115K FPP (Fixed Pitch Propulsion) Tankers for the Baltic ice class IA because the minimum power requirement of FMA (Finish- Swedish Maritime Association) needs quite large engine power and the 40 m Beam is out of calculation range of FMA minimum power requirements. The shipyard has no choice except to increase the engine power to satisfy FMA minimum power requirement Rule. And the operation cost, efficiency of hullform and its building cost are not good from the ship owners' point of view To solve this problem, the experience of ice breaking tanker development and the ice tank test results were adopted. The main idea to reduce the ice resistance is by reducing waterline angle at design load waterline. The reason behind the main idea is to reduce the ice-clearing force. Two hull forms were developed to satisfy Baltic Ice class IA. Two ice tank tests and one towing tank test was performed at MARC (Kvaener-Masa Arctic Research Center) and SSMB (Samsung Ship Model Basin) facilities, respectively. The purpose of these tests was to verify the performance in ice and open water respectively The hull form 2 shows less speed loss compared to Hull form 1 in open water operation but hull form 2 shows very good ice clearing ability. finally the Hull Form 2 satisfying Baltic ice class IA. The merit of this hull form is to use the same engine capacity and no major design changes in hull form and other related designs But the hull structure has to be changed according to the ice class grade. The difference in two hull form development methods, ice model test methods and analysis methods of ice model test will be described in this paper.

• Applied Chemistry for Engineering
• /
• v.18 no.5
• /
• pp.475-482
• /
• 2007

The thermal and optical properties of glucose penta(cholesteryloxycarbonyl)alkanoates (CAGLn, n = 2~8, 10, the number of methylene units in the spacer) were investigated. All the CAGLn formed monotropic cholesteric phases with left-handed helical structures. CAGLn with n = 2 or 10, in contrast with CAGLn with $3{\leq}n{\leq}8$, did not display reflection colors over the full cholesteric range, suggesting that the helical twisting power of the cholesteryl group highly depends on the length of the spacer joining the cholesteryl group to the glucose chain. The isotropic-cholesteric transition point ($T_{ic}$) decreased with increasing n and showed no odd-even effect. The plot of transition entropy at $T_{ic}$ against n had a sharp negative inflection at n = 7. The optical pitches (${{\lambda}_m}^{\prime}$ s) of CAGLn with $3{\leq}n{\leq}8$ decreased with increasing temperature. However, the temperature dependence of the ${\lambda}_m$ of the derivatives exhibited pronounced dependence on n. The transitional properties and the temperature dependence of the ${\lambda}_m$ observed for CAGLn were discussed in terms of the differences in arrangement of the cholesteryl groups and the conformation of the molecules.

• Journal of the Korean Society of Laryngology, Phoniatrics and Logopedics
• /
• v.7 no.1
• /
• pp.128-131
• /
• 1996

소아들의 음성장애의 대부분은 음성과 기능에 의한 성대의 오용 및 남용으로부터 기인한다. 그러나 음성장애에 대한 인식의 부족으로 인하여 소아의 음성장애 발견율은 극히 낮은 수준에 머므르고 있다. 치료에 있어서도 행동의 통제가 그다지 쉽지 않기 때문에 많은 어려움이 따른다. 본 연구는 소아의 음성장애의 발생경위와 문제의 설명과 차팅에 의한 남용의 감소에 초점을 둔 치료사례이다. 5세 아동의 심한 음성장애로 의뢰되어졌다. 음성증후는 목쉰소리, 기식화된 소리, 일시적인 발성일탈(phonation break) 등이 두드러졌다. 이비인후과 전문의의 스트로보스코프(stroboscope) 검진결과 초기 양측성 성대결절이 성대 앞쪽으로부터 1/3 지점에서 발견되었으며 비지피치(Visi-Pitch)로 측정된 퍼터베이션(perturbation 수치가 16.8이었다. 사례사 조사 과정에서 아동이 활동적이며 자주 고함을 지르고 자동차놀이를 주로하며 많은 시간을 보낸다는 것이 밝혀졌다. 중재 프로그램은 우선 문제를 설명하고 인식시키는 것과 고함을 지르거나 자동차놀이를 하면서 자동차 소음을 흉내내는 등의 음성남용 회수를 감소시키는 것에 초점을 두었다 17회의 치료로 성대결절이 감소되었고 퍼터베이션은 3.8로 저하되었으며 아동 스스로 음성남용을 통제할 수 있다는 임상적 판단하에 치료를 종결하였다. 1개월 후 추후 검사에서 남용적인 습관이 여전히 나타나지 않았으며 음성상태도 양호하였다. 소아 음성장애의 치료는 소아가 이해할 수 있는 용어로 문제의 인식을 확실히 시키고 행동을 체계적으로 통제할 수 있는 치료프로그램을 실행시키는 임상가의 자질이 대단히 중요하다. 그러나 그에 못지 않게, 많은 시간을 아동과 함께 보내는 부모나 교사의 협력이 치료의 성패를 좌우할 수 있다.조구와 처리구간에 차이가 없었다. 그러나 유지방 함량의 경우 대조구가 3.22%, 처리구가 3.37%로 처리구가 0.15% point 증가했으나 유의차는 없었다. Fan ＋ sprinkler가 설치된 시설에서 사육된 젖소에서 생산된 우유내 체세포수는 대조구에 비해 26.63%가 감소되었으나 유의차는 발견할 수 없었다. 이상의 시험 결과에서 볼 때 fan ＋ sprinkler를 이용한 방서 방법은 고온 stress를 완화시켜 유생산성의 증가에 기여할 수 있는 하나의 방법이라고 본다.을 알 수가 있었다.없다. 본 논문의 대상은 바로 이러한 합성 동사성명사의 논항구조와 동사성명사에 의해 하위범주화된 논항들의 문법적 실현양상이다..그 결과 심리적 특성과 사용자 수용 특성은 아바타 수용도에 부분적으로 영향을 미친다는 것 결과가 나타났다.웨어 프로세스 평가와 개선 모델의 개발을 위한 기초적인 자료를 제공할 것으로 예상된다 또한, 본 연구 결과는, 우리나라 소프트웨어 조직들이 실제로 무엇을 필요로 하는지를 밝힘으로써, 우리나라의 소프트웨어 산업을 육성하기 위한 실효성 있는 정책 입안을 위한 기초 자료를 제공할 것으로 예상된다.다.를 검증하려고 한다. 협력체계 확립, ${\circled}3$ 전문인력 확보 및 인력구성 조정, 그리고 ${\circled}4$ 방문보건사업의 강화 등이다., 대사(代謝)와 관계(關係)있음을 시사(示唆)해 주고 있다.ble nutrient (TDN) was highest in booting stage (59.7%); however no significant difference was found among other stages. The concentrations of Ca and P were not

• The Journal of Korean Society for Radiation Therapy
• /
• v.27 no.2
• /
• pp.115-122
• /
• 2015

Purpose : The aim of this study, evaluate the accuracy of HeaxPOD evo RT system using the non-coplanar beam. Materials and Methods : 13 treatment plans are used which applied non-coplanar beams and 10 treatment plans which coplanar beams are used. the correction value what adjust to 6D couch is determined by each patient's setup errors only rotation direction. The study executed followings. first, Applying the correction value, measure the point dose and calculate the ${\gamma}$-index(${\gamma}=3%$ / 3 mm, ${\gamma}=2%$ / 2 mm). second, acquire data as previous methods without correction by HexaPOD. Results : For comparing the two results, we find out the more precise applying HexaPOD by point dose 0.2% in coplanar and non-coplanar. in the case of ${\gamma}$-index<1(${\gamma}=3%$ / 3 mm), more precise 2.2% in coplanar and 7% in Non-coplanar. Particularly, ${\gamma}$-index<1(2% / 2 mm) show the difference 9.2% in coplanar and 15.1% non-coplanar between apply HexaPOD and dose not apply HexaPOD. Conclusion : Using the HexaPOD is more precise than without HexaPOD. It suggests that HexaPOD evo RT system is very useful for precise and high dose delivery.