• The Journal of the Korea institute of electronic communication sciences
• /
• v.15 no.1
• /
• pp.1-8
• /
• 2020

If a dangerous situation arises in a place where out of reach from the human, UAVs can be used to determine the size and location of the situation to reduce the further damage. With this in mind, this paper sets the minimum value of the roll, pitch, and yaw using beta flight to detect the UAV's smooth hovering, integration, and derivative (PID) values to ensure that the UAV stays horizontal, minimizing errors for safe hovering, and the camera uses Open CV to install the Raspberry Pi program and then HSV (color, saturation, Brightness) using the color palette, the filter is black and white except for the red color, which is the closest to the fire we want, so that the UAV detects the image in the air in real time. Finally, it was confirmed that hovering was possible at a height of 0.5 to 5m, and red color recognition was possible at a distance of 5cm and at a distance of 5m.

• Journal of the Ergonomics Society of Korea
• /
• v.35 no.5
• /
• pp.319-341
• /
• 2016

Objective:This research analyzed the lower-limb motion in kinetic and kinematic way while walking on various terrains to develop Foot-Ground Contact Detection (FGCD) algorithm using the Inertial Measurement Unit (IMU). Background: To estimate the location of human in GPS-denied environments, it is well known that the lower-limb kinematics based on IMU sensors, and pressure insoles are very useful. IMU is mainly used to solve the lower-limb kinematics, and pressure insole are mainly used to detect the foot-ground contacts in stance phase. However, the use of multiple sensors are not desirable in most cases. Therefore, only IMU based FGCD can be an efficient method. Method: Orientation and acceleration of lower-limb of 10 participants were measured using IMU while walking on flat ground, ascending and descending slope and stairs. And the inertial information showing significant changes at the Heel strike (HS), Full contact (FC), Heel off (HO) and Toe off (TO) was analyzed. Results: The results confirm that pitch angle, rate of pitch angle of foot and shank, and acceleration in x, z directions of the foot are useful in detecting the four different contacts in five different walking terrain. Conclusion: IMU based FGCD Algorithm considering all walking terrain possible in daily life was successfully developed based on all IMU output signals showing significant changes at the four steps of stance phase. Application: The information of the contact between foot and ground can be used for solving lower-limb kinematics to estimating an individual's location and walking speed.

• Journal of Convergence for Information Technology
• /
• v.7 no.5
• /
• pp.137-148
• /
• 2017

Recently, researchers are actively addressed to utilize Unmanned Aerial Vehicles(UAV) for military and industry applications. One of these applications is to trace the preceding flight when it is necessary to track the route of the suspicious reconnaissance aircraft in secret, and it is necessary to estimate the attitude of the target flight such as Roll, Yaw, and Pitch angles in each instant. In this paper, we propose a method for estimating in real time the attitude of a target aircraft using the video information that is provide by an external camera of a following aircraft. Various image processing methods such as color space division, template matching, and statistical methods such as linear regression were applied to detect and estimate key points and Euler angles. As a result of comparing the X-plane flight data with the estimated flight data through the simulation experiment, it is shown that the proposed method can be an effective method to estimate the flight attitude information of the previous flight.

• Journal of Advanced Navigation Technology
• /
• v.28 no.2
• /
• pp.178-184
• /
• 2024

The radar installed on an aircraft has various operating modes depending on tactical purposes, allowing for the configuration of search areas according to each mode's operational objectives. active electronically scanned array (AESA) radar emits search beams sequentially according to a predefined search beam grid within the designated search area specified by the pilot to detect targets within it. It is crucial that the radar can stably search the area designated by the pilot for target detection, even as the aircraft's attitude changes. This paper focuses on stabilizing the search pattern in the air-to-air operational mode of aircraft-mounted radar to ensure stable target detection during roll and pitch maneuvers of the aircraft. The paper demonstrates its performance by simulating aircraft maneuvers and targets in a system integration laboratory (SIL) test environment.

• Journal of the Korea Society of Computer and Information
• /
• v.15 no.4
• /
• pp.65-74
• /
• 2010

At the aim of solving the problems appearing in traditional optical motion capturing systems such as the interference among multiple patches and the complexity of sensor and patch allocations, this paper proposes a new motion capturing system which is composed of a single camera and multiple motion sensors. A motion sensor is consisted of an acceleration sensor and a gyro sensor to detect the motion of a patched body and the orientation (roll, pitch, and yaw) of the motion, respectively. Although Image information provides the positions of the patches in 2D, the orientation information of the patch motions acquired by the motion sensors can generate 3D pose of the patches using simple equations. Since the proposed system uses the minimum number of sensors to detect the relative pose of a patch, it is easy to install on a moving body and can be economically used for various applications. The performance and the advantages of the proposed system have been proved by the experiments.

• Transactions of Materials Processing
• /
• v.14 no.5 s.77
• /
• pp.473-476
• /
• 2005

The demand of on-chip total analyzing system with MEMS (micro electro mechanical system) bio/chemical sensor is rapidly increasing. In on-chip total analyzing system, to detect the bio/chemical products with submicron feature size, a filtration system with nano-filter is required. One of the conventional methods to fabricate nano-filter is to use direct patterning or RIE (reactive ion etching). However, those procedures are very costly and are not suitable fur mass production. In this study, we suggested new fabrication method for a nano-filter based on replication process, which is simple and low cost process. After the Si master was fabricated by laser interference lithography and reactive ion etching process, the polymeric mold was replicated by UV-imprint process. Metallic nano-filter was fabricated after removing the polymeric part of metal deposited polymeric mold. Finally, our fabrication method was applied to metallic nano-filter with $1{\mu}m$ pitch size and $0.4{\mu}m$ hole size for bacteria sensor application.

• Proceedings of the KIEE Conference
• /
• 2011.07a
• /
• pp.1794-1795
• /
• 2011

본 연구에서는 가속도 센서의 값을 디지털 신호 처리 과정을 통하여 저역통과 필터(low pass filter), 벡터의 크기(vector magnitude), 롤(roll) 그리고 피치(pitch)를 계산하는 알고리즘을 적용하였다. 필터의 경우 IIR(Infinite Impulse Response)을 이용하였으며 차수는 9차로 하였다. 피험자의 연령은 $25{\pm}5$세의 10명을 기준으로 실험하였으며 앞, 뒤, 좌, 우 방향으로 직각 낙하하도록 하였고 센서 모듈은 오른쪽 허리의 정중앙에 착용하도록 하여 피험자간의 오차가 발생하지 않도록 하였다. 환자의 낙상을 검출하기 위해서 벡터의 크기를 사용하였고 롤과 피치를 이용하여 환자의 낙상 방향을 검출하였다. 결과적으로 피험자 10명의 경우 낙상의 검출률은 100% 였으며 낙상 방향에 따른 앞, 뒤, 좌, 우 판별 정확도는 95% 정도이다. 낙상 방향의 판별은 사고 후 환자를 다룰 때의 주의할 신체부위를 참고하며 재활 운동 시 하체의 어느 쪽이 낙상의 주요인인지 분석하는 보조 자료가 될 수 있다.

• International Journal of Advanced Culture Technology
• /
• v.4 no.4
• /
• pp.81-86
• /
• 2016

In this paper, we propose a simple and effective vision-based tracking controller design for autonomous object tracking using multicopter. The multicopter based automatic tracking system usually unstable when the object moved so the tracking process can't define the object position location exactly that means when the object moves, the system can't track object suddenly along to the direction of objects movement. The system will always looking for the object from the first point or its home position. In this paper, PID control used to improve the stability of tracking system, so that the result object tracking became more stable than before, it can be seen from error of tracking. A computer vision and control strategy is applied to detect a diverse set of moving objects on Raspberry Pi based platform and Software defined PID controller design to control Yaw, Throttle, Pitch of the multicopter in real time. Finally based series of experiment results and concluded that the PID control make the tracking system become more stable in real time.

• Journal of Institute of Control, Robotics and Systems
• /
• v.20 no.9
• /
• pp.922-929
• /
• 2014

Wind turbines are in the limelight in the alternative energy industry. However, they face frequent and various problems during operation. We focused on the supervising of the blades of a wind turbine. In this paper, we present the design of a maintenance robot that takes the size of wind turbine blades into consideration, so the general form of the robot is a square with four wires fixed to its vertices and to the nacelle. After the robot is placed near the nacelle, it moves along the blades. We also designed an attitude control algorithm for the robot to maintain its balance. Our control algorithm for the robot consists of roll and pitch attitude controllers and a height controller. Each controller was designed independently and then superposed together. We used simulations to verify our control algorithm.

• 제어로봇시스템학회:학술대회논문집
• /
• 2000.10a
• /
• pp.457-457
• /
• 2000

The display module of PDP consists of a pair of fine electrode patterned panels. For example, in case of 42" PDP, thousands of electrode patterns should be placed on panel, where length, width, and height of each pattern m one meter, 50${\mu}{\textrm}{m}$, and 30${\mu}{\textrm}{m}$ respectively. And pitch between patterns is around 200${\mu}{\textrm}{m}$. Electrode patterns are frequently damaged during the production process, and thus might be broken. These breakage will result in open-circuited electrical characteristic of a pattern and/or open-circuited electrical characteristic between patterns. Therefore, inspection of pattern defects is the inevitable process to improve production yield rate of the panel. In this paper, we first review several types of PDP pattern defects which affects yield-rate of PDP. And, problems of inspecting such pattern defects by a typical inspection method is addressed. Then, a novel inspection method is proposed to overcome the difficulties, where some new components and the algorithm to detect the electrode defects are explored.ored.