• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2002년도 하계학술대회 논문집 B
• /
• pp.961-963
• /
• 2002

When high temperature superconducting(HTS) tapes are wound on former for HTS cable application, their critical characteristics are likely to be degraded seriously because of mechanical stress. In this study, prior to fabricate prototype HTS cables, we investigated the variation of critical characteristics of HTS tapes according to their pitch angles. For this work, we prepared the samples of HTS tapes on the former of which diameter is 3cm. Pitch angles of HTS tapes are $0^{\circ}$, $00^{\circ}$, $20^{\circ}$, $30^{\circ}$, $40^{\circ}$, respectively. We applied current up to 160 $A_{rms}$ to HTS tapes and investigated E-I characteristics. The critical current of HTS tapes was decreased as pitch angle increased. In addition, when the applied current was beyond their critical current, the rate of resistance increase of HTS tapes was in proportion to their critical current. Finally, We concluded that the pitch angles affected resistance increase of HTS tapes as well as critical current.

• Tribology and Lubricants
• /
• 제28권1호
• /
• pp.27-32
• /
• 2012

Oval gears are typical kinds of non-circular gears and are widely used in flow meters. This paper presents a tooth profile design of an oval gear according to the curvature of the pitch curve. The length of the pitch oval is divided by the number of teeth and the curvature of the divided points is obtained. The tooth profile is designed on the circle of the curvature as if it is the pitch circle of a gear. The teeth of the oval gear have the same module and pressure angle, but the pitch circle of each tooth differs in size. Thus, the teeth on the divided points of the pitch oval are different in shape. This type of oval gear will improve the meshing properties.

• 전력전자학회:학술대회논문집
• /
• 전력전자학회 2012년도 전력전자학술대회 논문집
• /
• pp.311-312
• /
• 2012

Blade pitch control system monitors and adjusts angle of the blades and controls rotation speed of blades. This paper shows 2MW pitch system hardware and electric part. Blade pitch system consists of pitch drive, gear box, motor and energy storage. Fieldbus is base on CANopen protocol. Fail-Safe system moves the blades to a safety position in case of any fault condition. The super capacitor energy storage provides emergency back up to the Pitch servo driver during feathering the blades. This paper studied Blade pitch servo driver and a bi-directional DC-DC converter for fail-safe system.

• 대한족부족관절학회지
• /
• 제11권1호
• /
• pp.67-71
• /
• 2007

Purpose: To evaluate clinical results of the 5th proximal metatarsal intraarticular fracture (Zone I) with displacement treated operatively and to evaluate predisposing factors of the 5th proximal metatarsal fracture (Zone I). Materials and Methods: 11 patients treated for the 5th proximal metatarsal fracture (Zone I) operatively and 10 patients treated conservatively between Jan 2003 and Dec 2005, were followed for more than one year. Functions were graded by AOFAS foot scoring system and union time and postoperative complications were also evaluated. Calcaneal pitch angle was also evaluated. Results: Clinically there were no much difference in results. Clinical points were 94.5 in the operative group and 92.3 in the conservative group. At the last follow-up, the radiographic results showed union in all cases. During the follow-up period, there were no significant complications. But in the conservative group, displaced fracture with calcaneal pitch angle over 30 degree tends to show delayed union and time to loss of pain tends to be prolonged. Conclusion: Calcaneal pitch angle is thought to predisposing factor for 5th metatarsal base fracture. Operative treatment is viable option for the 5th proximal metatarsal intraarticular fracture with displacement and with calcaneal pitch angle over 30 degree. In cases of cavovarus foot deformity, we think operative treatment should be considered with deliberation and long term follow-up study for peroneal tendinopathy should be needed.

• 대한기계학회논문집
• /
• 제15권6호
• /
• pp.1886-1896
• /
• 1991

본 연구에서는 부상높이를 예측할 수 있는 방법을 개발하고 연관된 변수들의 변동에 따른 부상높이를 검토함으로써 불안정한 극소 공기막 형성시 유발되는 자기헤 드와 하드 디스크간 정보손실 및 하드 디스크의 표면손상을 막고 고성능 자기기억장치 설계에 도움이 되고자 한다.

• 한국유체기계학회 논문집
• /
• 제11권1호
• /
• pp.9-17
• /
• 2008

A numerical study for three-dimensional laminar flow in the entrance region of helical tubes connected with straight ones is carried out to investigate the effects of Reynolds number, pitch and curvature ratio on the oscillation periods of the flow. The fully elliptic governing equations were solved by means of a finite volume method. The fully developed laminar flow boundary condition was applied at the straight tube inlet. This results cover a curvature ratio range of 1/10${\sim}$1/320, a pitch range of 0.0${\sim}$3.2, and a Reynolds number range of 62.5${\sim}$2000. A comparison is made with previous experimental correlations and numerical data. The developments of velocity, local and average friction factors are discussed. The average friction factors are oscillatory in the entrance region of helical pipes. It has been found that the angle required for the flow to be similarly developed is most affected by the curvature ratio. The pitch and Reynolds number do not have any significant effect on the angle. The characteristic angle ${\phi}_c(={\phi}/sqrt{\delta})$, or the characteristic length to diameter ratio $s_c(=l\sqrt{\delta} cos(atan{\lambda})/d)$, can be useful to represent the development of flow in helical tubes. As the pitch increases and as the curvature ratio and Reynolds number decrease, the amplitude and the number of flow oscillations along the main streamwise direction decrease.

• Journal of Electrical Engineering and Technology
• /
• 제9권3호
• /
• pp.835-842
• /
• 2014

Cutback control in a grid code is one of the functions of a wind power plant (WPP) that is required to support the system protection and frequency stability. When a cutback control command signal is delivered to the WPP from the system operator, the output of a WPP should be decreased to 20% of the rated power within 5 s. In this paper, we propose a dedicated cutback control algorithm of a WPP based on the ratio of the command power to the available power. If a cutback control signal is delivered, the algorithm determines the pitch angle for the cutback control and starts the pitch angle control. The proposed algorithm keeps the rotor speed at the speed before the start of the cutback control to quickly recover the previous output prior to the cutback control. The performance of the algorithm was validated for a 100 MW aggregated WPP based on a permanent magnet synchronous generator under various wind conditions using an EMTP-RV simulator. The results clearly shows that the proposed algorithm not only successfully reduces the output to the command power within 5 s by minimizing the fluctuation of the pitch angle, but also rapidly recovers to the output level before the cutback control.

• 대한기계학회논문집B
• /
• 제21권5호
• /
• pp.637-649
• /
• 1997

Effects of cone angle, pressure-hole orientation and Reynolds number on the five-hole probe calibration have been investigated for eight large-scale conical five-hole probes, which have either perpendicular pressure holes or forward-facing pressure holes for the cone angles of 45 deg, 60 deg, 75 deg and 90.deg. Pitch and yaw angles are changed from -40 deg to +40 deg with an interval of 5 deg, respectively, when the probe Reynolds numbers are 1.77*10$^{4}$, 3.53*10$^{4}$ and 7.06*10$^{4}$. The result shows that larger cone angle results in more sensitive changes in the calibration coefficients. In the case that the cone angle is 45 deg, the pitch-angle and yaw-angle coefficients of the five-hole probe with the perpendicular pressure holes show a very different trend compared with those of the five-hole probe with the forward-facing pressure holes. On the other hand, when the cone angle is more than 60 deg, each calibration coefficient is nearly independent of the pressure-hole orientation. Additionally, the effects of the Reynolds number on the calibration coefficients are also reported in detail.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2002년도 하계학술대회 논문집 B
• /
• pp.1358-1360
• /
• 2002

This paper presents a modeling and simulation of a utility-connected wind energy conversion system with a link of a rectifier and an inverter. It discusses the maximum power control algorithm for the wind turbine and presents the relationship of wind turbine output, rotor speed, power coefficient, tip-speed ratio and wind speed when the wind turbine is operated under the maximum power control algorithm. The control objective is to extract maximum power from wind and transfer the power to the utility. This is achieved by controlling the pitch angle of the wind turbine blades. Pitch control method is mechanically complicated, but the control performance is better than that of the stall regulation method. The simulation results performed on MATLAB will show the variation of generator's rotor speed, pitch angle, and generator output.

• 한국추진공학회지
• /
• 제15권5호
• /
• pp.27-34
• /
• 2011

초음속 항공기에서 피치 편향이 가능한 추력편향 노즐에 대한 해석적 연구를 수행하였다. 초음속 항공기의 비행조건에서 터보팬 엔진의 기본성능을 도출하였으며, 이를 바탕으로 이차원형태의 피치 편향이 가능한 추력편향 노즐을 설계하였다. 상용 해석프로그램인 Fluent 를 이용하여 축소확대 노즐에 대한 기본 유동특성을 파악하고, 피치 추력편향시의 유동특성과 비교하였다.