• Journal of the Korean Society of Manufacturing Technology Engineers
• /
• v.20 no.1
• /
• pp.47-52
• /
• 2011

It is well known that stiffness of composites depends on layup sequence of CFRP(carbon fiber reinforced plastics) laminates because the layup of composite laminates influences their properties. Ultrasonic NDE of composite laminates is often based on the backwall echoes of the sample. A pair of such transducers was mounted in a holder in a nose-to-nose fashion to be used as a scanning probe on composites. Miniature potted angle beam transducers were used (Rayleigh waves in steel) on solid laminates of composites. Experiments were performed to understand the behavior of the transducers and the nature of the waves generated in the composite (mode, wave speed, angle of refraction). C-scan images of flaws and impact damage were then produced by combining the pitch-catch probe with a portable manual scanner known as the Generic Scanner ("GenScan"). The pitch-catch signal was found to be more sensitive than normal incidence backwall echo of longitudinal wave to fiber orientation of the CFRP composites, including low level porosity, ply waviness, and cracks. Therefore, it is found that the experimentally Rayleigh wave variation of pitch-catch ultrasonic signal was consistent with numerical results and one-side ultrasonic measurement might be very useful to detect the defects.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.26 no.12
• /
• pp.1681-1691
• /
• 2002

The heat transfer and pressure drop characteristics of heat exchangers with louver fins were experimentally investigated. The samples had small fin pitches (1.0 mm to 1.4 mm), and experiments were conducted up to a very low frontal air velocity (as low as 0.3 m/s). At a certain Reynolds number (critical Reynolds number), the flattening of the heat transfer coefficient curve was observed. The critical Reynolds number was insensitive to the louver angle, and decreased as the louver pitch to fin pitch ratio (L$_{p}$F$_{p}$) decreased. Existing correlations on the critical Reynolds number did not adequately predict the data. It is suggested that, for proper assessment of the heat transfer behavior, the louver pattern in addition to the flow characterization need to be considered. The heat transfer coefficient increased as the fin pitch decreased. At low Reynolds numbers, however, the trend was reversed. Possible explanation is provided considering the louver pattern between neighboring fins. Different from the heat transfer coefficient, the friction factor did not show the flattening characteristic. The reason may be attributed to the form drag by louvers, which offsets the decreased skin friction at a low Reynolds number. The friction factor increased as the fin pitch decreased and the louver angle increased. A new correlation predicted 92% of the heat transfer coefficient and 90% of the friction factor within $\pm$10%.10%.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.40 no.3
• /
• pp.201-208
• /
• 2012

In this paper, a series of experiment is performed for a scaled hovering rotor in a semi-anechoic chamber and the results are compared to the noise spectra predicted by using Lowson's loading noise equation and FW-H equation. It was founded that the sound directivity pattern for both experiments and predictions are similar in their trend. Meanwhile the FW-H equation showed better agreement with experiments in the near-field noise spectra, but at the far-field the Lowson's equation performed better. The discrete noise are known to be proportional to the loading on the blades, which can be controlled by collective pitch angle of the blades. It was founded that the predicted spectra with FW-H equation come close to the measured noise spectra in low collective pitch, but in high collective pitch angles the Lowson's equation be more reliable.

• The Journal of the Acoustical Society of Korea
• /
• v.42 no.1
• /
• pp.7-15
• /
• 2023

Recently, as interest in air quality in vehicles increases, the use of fine dust detection sensors for air quality measurement is becoming common. An axial-flow fan is inserted in the fine dust sensor installed in the air conditioning system in the vehicle to prevent dust from sinking directly on the sensor. When the sensor operates, the flow noise caused by the rotation of the axial-flow fan acts as a major noise source of the fine dust sensor. flow noise is recognized as one of the product competitiveness of fine dust sensors. In this study, the noise was gradually reduced at the same flow rate by improving the flow performance of the small axial flow fan. First, a virtual fan performance tester consisting of about 20 million grids was developed to analyze the aerodynamic performance of the target small axial-flow fan. In addition, the flow field was simulated by using compressible Large Eddy Simulation for direct computation of flow noise as well as high-accurate prediction of flow rate. The validity of numerical method are confirmed through the comparison of predicted results with experimental ones. After the effects of pitch angle on flow performance were analyzed using the verified numerical method, the pitch angle was determined to maximize the flow rate. It was found that the flow rate was increased by 8.1 % and noise was reduced by 0.8 dBA when the axial-flow fan with the optimum pitch angle was used.

• Transactions on Control, Automation and Systems Engineering
• /
• v.4 no.3
• /
• pp.231-238
• /
• 2002

In this paper, we present a new approach to autopilot design for skid-to-turn missiles which may have severe aerodynamic cross-couplings and nonlinearities with angle of attack. The model of missile motion is derived in the maneuver plane and, based on that model, pitch, yaw, and roll autopilot are designed. They are composed of a nonlinear term which compensates for the aerodynamic couplings and nonlinearities and a linear controller driven by the measured outputs of missile accelerations and angular rates. Besides the outputs, further information such as Mach number, dynamic pressure, total angle of attack, and bank angle is required. With the proposed autopilot and simple estimators of bank angle and total angle of attack, it is shown by computer simulations that the induced moments and some aerodynamic nonlinearities are properly compensated and that the performance is superior to that of the conventional ones.

• 제어로봇시스템학회:학술대회논문집
• /
• 1993.10a
• /
• pp.793-798
• /
• 1993

In this study the attitude control of the KOREASAT is investigated. The KOREASAT is a geostationary satellite and its 3 attitude angles, namely, roll, pitch and yaw angles, are stabilized by using the 3-axis stabilization technique. In the pitch control loop, the pitch attitude angle received from the earth sensor is processed in the attitude processing electronics by using PI type control logic, and the control command is sent to the momentum wheel assembly to generate the control torque by varying the wheel rate. The roll/yaw attitude control is performed by activating a magnetic torquer or by firing appropriate thrusters. The magnetic torquer interacts with the earth magnetic field to produce the control torque, and the thrusters are used to control the larger roll attitude errors. In this study dynamic modelling of the satellite is performed. And the earth sensor, the momentum wheel, and the magnetic torquer are mathematically modelled. The 3-axis attitude control logic is implemented to make the closed-loop system and simulations are carried out to verify the implemented control laws.

• Proceedings of the KIEE Conference
• /
• 2005.10b
• /
• pp.376-378
• /
• 2005

In this study, we have evaluated and classified arthritic pathology using the acoustical analysis of knee joint sounds. Six normal subjects and 11 patients with knee problems were enrolled. Patients were divided into the 1st patient group which required an orthopeadic surgery and the 2nd patient group of osteoarthritis. During sitting and standing periods, subjects' active knee flexion and extension were monitored. Fundamental frequency, mean amplitude of pitch, jitter and shimmer were analyzed according to the position and the joint angle. The result showed that the fundamental frequency of the 2nd patient group and standing position was higher than the others, and that the pitch of sounds changed unstably.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2010.06a
• /
• pp.177-177
• /
• 2010

본 연구에서는 반도체용 Si wafer에 마스크 공정 및 slit etching 공정을 적용하여 목표인 30um 이하의 Probe unit을 개발하기 위해 Deep Si Etching(DRIE) 장비를 이용하여 식각 공정에 따른 특성을 평가하였다. 마스크는 Probe block 조립에 적합한 패턴으로 설계 하였으며, slit의 에칭된 지점에 pin이 삽입될 수 있도록 그 폭을 최소한으로 설계하였다. 30um pitch와 20um pitch의 마스크를 각각 설계하여 포토공정에 의해 마스크패턴을 제작하였으며, 식각공정 결과 식각율 5um/min, profile angle $89^{\circ}{\pm}1^{\circ}$로 400um wafer의 양면관통 식각을 확인하였으며, 표면 및 단면 식각특성을 조사하였다.

• 유체기계공업학회:학술대회논문집
• /
• 2000.12a
• /
• pp.193-199
• /
• 2000

The effects of Reynolds number on the non-nulling calibration of a cone-type five-hole probe in low-speed flows have been investigated at the Reynolds numbers of $2.04{\times}10^3,\;4.09{\times}10^3$, and $6.13{\times}10^3$. The calibration is conducted at the pitch and yaw angles in ranges between -35 degrees and 35 degrees with an angle interval of 5 degrees. The result shows that each calibration coefficient, in general, is a function of the pitch and yaw angles, so that the pre-existing calibration data in a nulling mode are not enough in accounting for the full non-nulling calibration characteristics. Due to the interference of the probe stem, the calibration coefficients have more Reynolds number sensitivity at positive pitch angles than at negative ones.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2002.05a
• /
• pp.25-28
• /
• 2002

This paper is concerned with the design of roller profiles in tube/pipe straightener with both methods of Computer Aided Design and Computer Aided Engineering. Design analysis is carried out from two point of view. The one is the research in the minimization of tube pitch which was very important factor in levelling process. In order to minimize tube pitch, profiles of the roller were calculated so that the contact region between roller and tube was maximized. The other is determination of an optimum amount of intermesh for the proper progress without a jam in levelling process. Generally the jamming trouble was casued by excessive amount of intermesh in levelling process. The optimum amount of intermesh was determined through the finite element analysis.