• International Journal of Naval Architecture and Ocean Engineering
• /
• 제9권1호
• /
• pp.1-10
• /
• 2017

Various offshore structures such as FPSO, FSO, Semi-submersible, TLP and Spar are operated to develop offshore oil and gas fields. Most of the offshore structures shall be operated over 20 years under the harsh environments at sites so that the offshore structures should be designed to endure the harsh environments. In this study, the effect of the impact load (so called slapping load) by the steep waves acting on the FPSO bow is investigated through the model test. For measurement of the impact pressures on the frontal area, a bow-shaped panel was fabricated, and installed the pressure sensors on the bow starboard side of the model FPSO. During the model test campaign, the impact load was investigated using the steep waves with $Hs/{\lambda}$ greater than 1/16 of the representative wave condition. Consequently, it is confirmed through the model test that the impact loads acting on the FPSO bow are significantly increased with the steep waves ($Hs/{\lambda}$ > 1/16) than the representative wave conditions of a maximum significant wave height and a pitch forcing period. Therefore, for safe design of North Sea FPSO, it is necessary to consider the steep waves in addition to the representative wave conditions and to be applied as proper structural load. Also, the effect of random seeds in irregular waves should be considered to build the safe FPSO.

• Journal of Mechanical Science and Technology
• /
• 제16권11호
• /
• pp.1412-1419
• /
• 2002

Dynamic shear tests for the tough-pitch copper at high strain and high strain rate was performed. The Split Hopkinson Pressure Bar (SHPB) compression test system was modified to yield a shear deformation in the specimen. Hat-shaped specimens for the tough-pitch copper were adopted to generate high strain of γ=3～4 and high strain-rate of γ= 10$^4$/s. The dynamic analysis by ABAQUS 5.5/EXPLICIT code verified that shear zone can be localized in hat-shaped specimens. A proper impact velocity and the axial length of the shear localization region wert determined through the elastic wave analysis. The displacement in a hat-shaped specimen is limited by a spacer ring which was installed between the specimen and the incident bar. The shear bands were obtained by measuring the direction of shear deformation and the width of deformed grain in the shear zone. The decrease of specimen length has been measured on the optical displacement transducer. Dynamic shear stress-strain relations in the tough-pitch copper were obtained at two strain-rates.

• 한국정보통신학회논문지
• /
• 제13권2호
• /
• pp.330-340
• /
• 2009

함정은 해상 운용 시 파도 및 바람의 영향으로 인하여 Pitch Roll 방향으로 운동이 불가피하다. 따라서 함정은 전 후 좌우로 연속적으로 회전 운동을 한다. 그리고 함정은 내부 장비들의 가진에 의한 다양한 주파수의 진동과 강한 파도, 폭발에 의한 충격 등의 외란 신호에 항상 노출되어 있다. 본 논문에서는 실제 시스템과 유사한 전산해석 모델을 작성한 후 외란 신호를 포함한 함정의 연속적인 거동에 대하여 2축 안정화 장치 의 동적 거동 및 위치 제어 전산해석을 수행한다.

• 한국운동역학회지
• /
• 제17권2호
• /
• pp.177-185
• /
• 2007

Even though there were no clear definitions of the short game and short game distance, short game capability is crucial for a good golf score. Generally, chip shot and pitch shot are regarded as two principal components of the short game. Chip shot is a short, low trajectory shot played to the green or from trouble back into play. Pitch shot is a high trajectory shot of short length. Biomechanical studies were conducted usually to analyze full swing and putting motions. The purpose of the study was to reveal the kinematical differences between professional golfers' 30 yard $53^{\circ}wedge$ chip shot and $56^{\circ}wedge$ pitch shot motions. Fifteen male professional golfers were recruited for the study. Kinematical data were collected by the 60 Hz three-dimensional motion analysis system. Statistical comparisons were made by paired t-test, ANOVA, and Duncan of the SPSS 12.0K with the $\alpha$ value of .05. Results show that both the left hand and the ball were placed left of the center of the left and right foot at address. The left hand position of the chip shot was significantly left side of that of the pitch shot. But the ball position of the pitch shot was significantly right side of that of the chip shot. All body segments aligned to the left of the target line, open, at address. Except shoulder, there were no significant pelvis, knee, and feet alignment differences between chip shot and pitch shot. These differences at address seem for the ball height control. Pitch shot swing motions(the shoulder and pelvis rotation and the club head travel distance) were significantly bigger than those of the chip shot. Club head velocity of the pitch shot was significantly faster than that of the chip shot at the moment of impact. This was for the same shot length control with different lofted clubs. Swing motion differences seem mainly caused by the same shot length control with different ball height control.

• Ocean Systems Engineering
• /
• 제9권4호
• /
• pp.349-368
• /
• 2019

Triceratops is one of the new generations of offshore compliant platforms suitable for ultra-deepwater applications. Apart from environmental loads, the offshore structures are also susceptible to accidental loads. Due to the increase in the risk of collision between ships and offshore platforms, the accurate prediction of structural response under impact loads becomes necessary. This paper presents the numerical investigations of the impact response of the buoyant leg of triceratops usually designed as an orthogonally stiffened cylindrical shell with stringers and ring frames. The impact analysis of buoyant leg with a rectangularly shaped indenter is carried out using ANSYS explicit analysis solver under different impact load cases. The results show that the shell deformation increases with the increase in impact load, and the ring stiffeners hinder the shell damage from spreading in the longitudinal direction. The response of triceratops is then obtained through hydrodynamic response analysis carried out using ANSYS AQWA. From the results, it is observed that the impact load on single buoyant leg causes periodic vibration in the deck in the surge and pitch degrees of freedom. Since the impact response of the structure is highly affected by the geometric and material properties, numerical studies are also carried out by varying the strain rate, and the location of the indenter and the results are discussed.

• 대한기계학회논문집A
• /
• 제25권1호
• /
• pp.98-105
• /
• 2001

The fundamental and widely used spot welded sections of automobiles (hat and double hat-shaped section members) absorb most of the energy in a front-end collision. The sections were tested on axial static(10mm/min) and quasi-static(1000mm/min) loads. Based on these test results, specimens with various thickness, shape and spot weld pitch on the flange have been tested with impact velocity(7.19m/sec) the same as a real life car clash. Characteristics of collapse have been reviewed and a structure of optimal energy absorbing capacity is suggested.

• 한국염색가공학회지
• /
• 제30권4호
• /
• pp.313-320
• /
• 2018

As carbon fiber reinforced composites(CFRP) are widely used in aerospace, automobile, marine, and sports goods applications, they have been studied extensively by various researchers. However, CFRP have been pointed out because of machining problems such as delamination and burr phenomenons. Especially, hole machining process, drilling, has non-smooth features on inlet and outlet surfaces of drilled hole. This kind of machining problem can be controlled to some extent by using high modulus pitch-CF, which has considerable effects on fracture behavior of composite compared with only PAN CF composite. Therefore, PAN and pitch hybridized CF composites were prepared having high strength and modulus. The results demonstrate that the hybrid CFRP specimens with pitch CF offer the good potential to enhance modulus as well as strength properties. Dynamic mechanical, flexural, and impact properties were measured and analyzed. Morphological surface of the composites were also observed by IFS-28, canon after hole machining.

• Journal of Advanced Marine Engineering and Technology
• /
• 제27권1호
• /
• pp.76-81
• /
• 2003

The purpose of this study is to analyze the collapse characteristics of widely used spot welded section members coated damping material Y1000 and to develop an analysis method for acquiring exact collapse loads and energy absorption ratio. Hat-shaped thin-walled members have the biggest energy absorbing capacity in a front-end collision. The sections were tested on quasi-static and impact loads. Specimens with two type thickness, width ratio and spot weld pitch on the flange have been tested in impact velocities(6.73n0sec and 7.54n1sec) which imitate a real-life car collision. As a result, it was developed the system for acquiring impact energy absorbing characteristics of structure united thin-walled member and damping materials.

• International Journal of Aerospace System Engineering
• /
• 제2권2호
• /
• pp.83-86
• /
• 2015

Taking the four-wheel bogie landing gear as an example, the force status of truck-like landing gear during the landing impact was analyzed and the simulation model of four-wheel bogie landing gear was established. Firstly, a landing gear prototyping model was established using CATIA and imported to LMS Virtual.lab. Secondly, dynamic analysis of the landing impact was simulated with the established model. Finally, with the help of LMS Virtual.lab's parametric design ability, the effects of landing approach and truck pitch angle on the landing performance, truck motion and truck beam strength were studied. These conclusions will be useful to the design and analysis of the truck.

• 말소리와 음성과학
• /
• 제1권1호
• /
• pp.87-91
• /
• 2009

The purpose of this study was to examine the characteristics of prosody of utterance of ambiguous sentences in patients with neurogenic communication disorders. Ambiguous words on which prosody may have an impact were used to investigate this matter. The characteristics of tone duration, pitch and intensity were analyzed to examine the characteristics of prosody in patients with lesions in the left or right hemisphere and normal controls. The whole process was recorded using a Praat 4.3.14 and for statistical analyses, two-way Anova and multiple comparative analyses were carried out using SPSS10.0 for Windows. The conclusions of this study are as follows: The length of vowel in homograph in Korean was different depending on the meaning and the duration of vowel was the longest in patients with lesions in the left hemisphere. There was agreed that they had problem of timing of prosody(Danly & Shapiro, 1982). On the other hand, there found that patients with lesions in the right hemisphere had deficiency of changeability in pitch. Among various acoustic parameters, this study focused on the duration which are closely related to suprasegmental characteristics of prosody. More acoustic parameters should be taken into account in future studies.