• KSTLE International Journal
• /
• v.3 no.1
• /
• pp.1-6
• /
• 2002

The purpose of this paper is to investigate the effects of design parameters on the friction loss in piston skirt. An analytical model to describe the friction characteristics of piston skirt has been presented, which is based on the secondary motion of piston and mixed lubrication theory, It could be shown that the skirt friction closely depends on the side force acted on the piston pin. The side force is inf1uenced by cylinder pressure at low engine speed, but by inertia force at high engine speed. The usage of extensive skirt area and low weight piston is effective to reduce the friction loss at high speed. The low viscosity oil considerably decreases viscous friction as engine speed increases, but it increases boundary friction at low engine speed. From the parametric study, it is found that the skirt axial profile is the most important design parameter related to the reduction of skirt friction.

• Journal of the korean Society of Automotive Engineers
• /
• v.12 no.4
• /
• pp.66-74
• /
• 1990

Friction between piston-ring assembly and cylinder wall of a spark ignition engine was evaluated under various engine operating conditions utilizing a grasshopper linkage system. The friction force was estimated by the force balance relation at the small end of connecting rod. Three forces were chosen to be measured for the objective. They were gas pressure inside the cylinder, inertia force of the piston-ring assembly, and the force exerted by the connecting rod. These forces were measured by a piezo type pressure sensor, an accelerometer and strain gauges, respectively. Comparisons were made with the frictional force evaluated by the conventional method where the assumption of constant rotational speed of engines was adopted. Due to the variation of rotational speed of engines, the conventional method was found to lead to a large error in the evaluation of the frictional force.

• Tribology and Lubricants
• /
• v.21 no.1
• /
• pp.39-45
• /
• 2005

Investigation of the mass effect on the journal traces in the clearance of engine bearing has been performed for better design of mass distribution of crank system components such as crank pin, piston, con-rod, balance weight, crank throw weight, etc. as well as for better oil reaction behaviors to the applied forces from the cylinder pressures on the bearing. In this preliminary study, crank pin traces in the engine bearing clearance are computed by varying the equivalent magnitude of crank pin mass that includes the masses of crank pin, piston, con-rod. etc.. while most previous studies regarding journal traces in the bearing clearance neglect the inertia effects of crank pin mass. Although the inertia effect of pill mass is negligibly small compared to viscous force by ${\pi}bearing$ theory, it is found that it gives a great amount of influences on the journal traces in full bearing computation $(2\pi\;bearing\;theory)$ under the dynamic loading conditions.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.1 no.3
• /
• pp.22-33
• /
• 1993

A theoretical analysis of predicting the detailed motion of a piston-crank mechanism within piston-guide clearance is presented, and the analysis is applied to the piston motion in a gasoline engine. A piston movement program is developed to calculate the piston attitude relative to the bore, the piston to bore impact velocity and kinetic energy loss and the net transverse force acting on the piston. This paper presents the formulation of a set of differential equations governing the transverse and rotational motion of a piston. These equations of motion were solved by well established Runge-Kutta method. As a result of this study, it is possible to predict the effects of piston geometry and piston pin offset on a piston motion and kinetic energy loss.

• Journal of Mechanical Science and Technology
• /
• v.17 no.6
• /
• pp.844-853
• /
• 2003

In this paper, a dynamic analysis of the reciprocating compression mechanism of a small refrigeration compressor is performed. In the problem formulation of the mechanism dynamics, the viscous frictional force between the piston and the cylinder wall is considered in order to determine the coupled dynamic behaviors of the piston and the crankshaft. Simultaneous solutions are obtained for the equations of motion of the reciprocating mechanism and the time-dependent Reynolds equations for the lubricating film between the piston and the cylinder wall and for the oil films on the journal bearings. The hydrodynamic forces of the journal bearings are calculated by using a finite bearing model along with the Gumbel boundary condition. A Newton-Raphson procedure is employed in solving the nonlinear equations for the piston and crankshaft. The developed computer program can be used to calculate the complete trajectories of the piston and the crankshaft as functions of the crank angle under compressor-running conditions. The results explored the effects of the radial clearance of the piston, oil viscosity, and mass and mass moment of inertia of the piston and connecting rod on the stability of the compression mechanism.

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.14 no.1
• /
• pp.24-31
• /
• 2004

Recently, as the marine compressor power is increased, vibration problems on the marine vessel with V/W type reciprocating compressor have been occurred. A research on the balancing of marine V/W type reciprocating compressor has hardly been reported though a number of researches on the balancing of rotating machinery have been conducted. As a V/W type compressor has high capacity with long stroke, compact size and high center of gravity, It is easy to have a vibration problem by a little bit unbalanced force and moment. In this study, calculation methods for balance weight of the V/W type reciprocating compressors, which have different piston weight and asymmetry structure, are formulated. And their reliability were verified by comparing calculated balance weight with the experimental results of the real marine V/W type reciprocating compressors.

• Tribology and Lubricants
• /
• v.17 no.6
• /
• pp.426-434
• /
• 2001

The hermetic reciprocating compressor driven by the BLDC motor rotating with variable speeds, is modelled and analyzed for dynamic characteristics. The governing equations of piston, connecting rod and crank-shaft of the reciprocating compression mechanism and characteristics of driving torque of the motor are obtained. Dynamic behavior of the crankshaft supported on 2 journal bearings is analyzed considering compression load and eccentric unbalance for the 4 rotating speeds of crankshaft. And. reaction forces generated from oil film in the journal bearings are analyzed under transient condition using Reynolds' equation. To take into account the dynamic characteristics depending on the variable rotating speeds, comparison on the dynamic behavior of crank-shaft is made for the 4 operating modes of the compressor. Results show that the magnitude of crankshaft locioperating on the lower rotating speeds is more larger than the higher ones due to reduction of inertia force of the reciprocating piston.

• Journal of Drive and Control
• /
• v.13 no.3
• /
• pp.32-38
• /
• 2016

For this paper, the position-control performances of dual EHA(electro-hydrostatic actuator) systems were investigated according to two cases wherein the double-rod- and single-rod-type hydraulic cylinders were combined. Since the control performance is significantly dependent on the load conditions including external forces such as the inertia load, it is proposed here that the two sub-EHAs are driven by separate position and force controllers, instead of two identical position controllers. According to the simulation results, the best performance was achieved by the position-controlled single-rod-type EHA that was combined with a force-controlled double-rod-type EHA. As the force-controlled double-rod-type EHA compensated for the external loads on the position-controlled single-rod-type EHA, the position-control performance was not influenced by external forces including the inertia load. In addition, the position-controlled single-rod-type EHA contributed to the enhancement of the damping ratio by absorbing the pressure peaks through its internal accumulator. Due to the symmetrical piston areas, the double-rod-type EHA is more suitable for force control than the single-rod- type EHA.

• Journal of the Korean Society for Precision Engineering
• /
• v.18 no.10
• /
• pp.194-199
• /
• 2001

In this paper, we propose a new locomotive mechanism using impulsive force for microcapsule-type endoscope. It has the compact size for movement in the colon and actuating mechanisms for hi-directional movement. The actuating mechanism resembles a pneumatic cylinder and consists of body, inertia mass(piston). spring. pneumatic source and calve. When valve is ON, the pneumatic impulsive force between piston and body drives them in two opposite direction. As the air in the body is passed away, the contrary movements are occurred by spring reaction. Therefore, the direction of body's motion is determined by the relative magnitude of two opposite impulsive forces, i.e., pneumatic and spring force. The effect of two impulsive forces can simply be controlled by On-Off time of solenoid valve.

• Journal of the Korea Convergence Society
• /
• v.13 no.4
• /
• pp.307-313
• /
• 2022

The importance of engine vibration reduction is increasing as the vehicle interior noise becomes more serious due to higher output and lighten weight trends. Recently, the balance shaft attachment has been proposed as a representative method for the engine vibration reduction. The balance shaft is a device that cancels the vibrations generated in the reciprocating motion of the piston and the conrod by using an arbitrary eccentric mass, and can improve fuel efficiency and ride comfort at the same time. This paper proposes the unbalance amount and shape of the balance shaft to induce and offset the inertia force generated by the engine structure. The proposed two-shaped balance shaft was implemented as an ADAMS multi-body dynamics model, and the reduction of the inertial force in the actual behavior was confirmed through dynamic simulation.