• 한국융합학회논문지
• /
• 제11권7호
• /
• pp.163-167
• /
• 2020

본 연구에서는 피스톤 헤드의 형상별 열응력해석을 진행하여 내구성이 있는 피스톤의 형상을 고찰하기 위한 연구를 진행하였다. 그 결과로서는 온도가 가해지는 부분에서부터 거리가 멀수록 낮은 온도를 볼 수 있다. 피스톤 헤드의 형상에 따라 열을 받는 면적이 다르기 때문에 피스톤 기둥 부분과 스커트부에 영향을 끼치게 된 점을 볼 수 있었다. 본 연구에서는 세 모델이 동일하게 피스톤 헤드의 중심부에서 가장 적은 응력이 나오는 것을 알 수 있었다. Model A는 다른 두 모델에 비해 항복이 발생하는 응력이 가장 작은 것을 알 수 있었다. Model B는 접시형 피스톤헤드로서 피스톤 헤드부가 오목한 형상으로 되어 있어 피스톤 헤드 중심부에서는 주변 부분에 영향을 가장 덜 끼치는 모델임을 알 수 있었다. Model C는 항복이 발생하게 되는 응력이 가장 크게 보였다. 또한 본 연구결과는 내구성이 있는 피스톤의 형상 설계에 유용하게 적용할 수 있다고 사료된다. 피스톤 헤드의 형상에 따른 열응력 해석을 적용함으로서, 본 연구가 미적인 융합에 부합된다고 사료된다.

• 한국전산유체공학회지
• /
• 제4권3호
• /
• pp.21-27
• /
• 1999

In this paper, tile characteristics of flow resulting from the configurations of piston head and intake-port of the cylinder in a gasoline-direct-injection engine are investigated numerically. Calculations are carried out from intake process to the end of compression. GTT code which includes the third order upwind Chakravarthy-Osher TVD scheme and κ-ε turbulence model with the law of wall as a boundary condition. As a result, a piston head with a smaller radius of curvature and larger radius gives stronger reverse tumble. It is also shown that as the maximum tumble ratio increases by the configuration of the intake-port the tumble ratio at the end of compression stroke increases. It is concluded that flows at the end of compression stroke can be controlled by the optimum design of intake-port and piston head.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 1995년도 추계학술대회 논문집
• /
• pp.985-990
• /
• 1995

Recently, the development of high speed and high precision NC-lathe for piston head machining is needed for the complexity and diversity of the piston head shape used in automobile reciprocating engine. THe piston head has many complex shapes in the aspect of fuel economy, such as ovality, profile, double ovality and recess. Among them, for the maching of the over shape of 0.1~1mm the cutting tool should move periodically symchronized with the rotation of piston workpiece. The cutting tool feeed system must have high positioning accuracy for the precise machining, high speed for the fast maching and high dynamic stiffness for the cutting force. The linear brushless DC motor is used for satisfying these coditions. The ballbush guide and supporting guide using turcite is used for the guidance of the feed drive system. Linear encoder, digital servo ampllifer and controller are used for driving the motor. THis paper presents the design and simulation of the new tool feed system for noncircular machining.

• Tribology and Lubricants
• /
• 제25권5호
• /
• pp.330-334
• /
• 2009

Hydraulic servo cylinders have been used to control accurately a large machine in power plant. Especially, Piston head and bush of servo cylinder is assembled sleeve and piston head and bush made of Cu alloy and pad sealing part. A damages of sleeve and piston head, bush are caused by friction and wear. Thus, It is necessary to examine friction and wear characteristics of Cu alloys for the piston head and bush. In this study, to be reliable on the piston and cylinder parts, dry friction and wear experiments were carried out with Cu alloys of four kinds of AlBC, PBC, BC and BS using reciprocating friction tester of pin on disk type. From this study, the result was shown that the AlBC and PBC with alloy elements were excellent to resistance wear. As the sliding speed was increased, the wear loss of PBC decreased than another Cu alloy.

• 한국자동차공학회논문집
• /
• 제8권6호
• /
• pp.79-86
• /
• 2000

The effects of recirculated exhaust gas on the wears of piston and piston rings were investigated by the experiment with a two-cylinder, four cycle, indirect injection diesel engine operating at an engine load of 75% and an engine speed of 1600 rpm. For the purpose of comparison between the wear rates of two cylinders with and without EGR, the recirculated exhaust gas was sucked into one of two cylinders after the soot contenets in exhaust emissions were removed by an intentionally designed cylinder-type scrubber equipped with 6 water injectors(A water injector has 144 nozzles of 1.0 mm diameter), while only the fresh air was inhaled into the other cylinder. These experiments were carried out on the fuel injection timing fixed at 15.3$^{\circ}$ BTDC. It was found that the wear rate of piston skirt with EGR increased a little bit, but the piston head diameter increased, rather than decreased, owing to soot adhesion and erosion wear, and especially larger with EGR, and that the wear rates of the top and second piston ring(compression ring)thickness with EGR were more than twice the wear rate of top ring in case of no EGR, but the wear rate of oil rings thickness without EGR increased greater than that with EGR.

• Journal of Mechanical Science and Technology
• /
• 제16권4호
• /
• pp.557-563
• /
• 2002

In this paper, the characteristics of flow and spray motions affected by from piston head configurations were investigated numerically. Calculations were carried out from intake process to the end of compression. GTT (Generalized Tank and Tube method) code, which includes a third order upwind Chakravarthy-Osher TVD scheme and k-$\varepsilon$ turbulence model with fuel spray analysis was used for the calculations. As a results, piston heads with smaller radii of curvature were found to give stronger reverse tumble than those with larger radii of curvature. Similar results are shown in the convection and diffusion of fuel sprays.

• 한국자동차공학회논문집
• /
• 제6권6호
• /
• pp.267-275
• /
• 1998

In this study, the instantaneous heat flux measurement probe and the linkage system for the measurement of the instantaneous temperature and heat flux of the DI mono cylinder diesel engine were developed, and these were proved to have a good reliability and sensibility. A 3-D FEM model which consist of full piston to accommodate the eccentric bowl in the piston head, was applied for the analysis of the thermal stress and the temperature distribution. The mean heat flux on the piston head was used as boundary condition for the analysis of piston. The analysis showed that thermal stress concentrate on the bowl and inner surface of pin hall.

• 한국공작기계학회:학술대회논문집
• /
• 한국공작기계학회 2002년도 춘계학술대회 논문집
• /
• pp.435-439
• /
• 2002

In the pneumatic system, pneumatic cylinder is wildly used to factory automation. In general, Pneumatic cylinder problems are occured with colliding to stroke end part at which piston collide to end-cap, head cap and tube when piston is loading. This appearances have a short life of cylinder and is due to system destruction. This study examines the dynamic characteristics of pneumatic cushioning cylinder and cushion sleeve design. At head part cushion chamber for the vertical experimental, The decisions of cushioning effect and the results of the experimental research are obtained to the followings: i) The cushioning effects could acqure to the reserch, if the compressible energy is more than kinetic ones. ii) The collision of piston and head cover could acqure to the research, if the kinetic energy is more than compressible iii) If the load increase to the rolling car, the cushion region pressures would increase and the dynamic force.

• Tribology and Lubricants
• /
• 제27권2호
• /
• pp.65-70
• /
• 2011

The power servo cylinder for driving accurately turbine stop valve of an atomic power plant is necessary to do turn-over owing to a leakage of oil and a structure problem, especially, it of a power plant be in demand a high quality standard depends entirely on import. There are much problem that the AlBC be to used as a material of piston head in cylinder are caused by wear. Therefore, it is necessary to examine friction characteristics of it. In this study, wear test experiments was carried out with AlBC and SCM440, using reciprocating friction tester of pin on disk. This result was shown that the wear mechanism of AlBC on working condition is adhesive wear and the maximum temperature of infra redray thermal image of frictional surface show over 2 mm from contact surface of pin and disk.

• 한국수소및신에너지학회논문집
• /
• 제19권3호
• /
• pp.182-188
• /
• 2008

In order to improve scavenging performance of free piston hydrogen fueled engine, this study estimate compatibility of uni-flow scavenging. The scavenging flow characteristics in the cylinder is investigated by flow visualization and PIV method. Consequently it has been found that the scavenging performance decreased with abnormal expansion of piston and delay of the exhaust valve opening timing. And the scavenging performance of exhaust valve located center in cylinder head is better than that of exhaust valve located side in cylinder head.