• 한국화재소방학회논문지
• /
• 제29권3호
• /
• pp.21-30
• /
• 2015

본 연구는 스프링클러설비용 CPVC관과 신축배관 접속부분에서의 누수저감을 위하여 신축배관을 연결하기 위한 밸브소켓과 신축배관 너트부분에 삽입되는 수밀 고무패킹 재질에 대한 국내 및 국외 관련 규격의 검토와 관련 시험 등을 통해 대책을 제안하고자 한다. 누수시험을 통해 밸브소켓 재질은 신축배관 너트부분이 금속제인 경우 금속제로 사용하거나 신축배관 너트부분의 재질을 합성수지제로 사용하여야함을 알 수 있었다. 또한 밸브소켓의 적정 품질 확보를 위해서는 나사산 규격과 검사기준으로 KS B 0221(관용평행나사)와 나사산 검사규격을 KS B 5223(관용 평행나사 게이지)에 따르도록 관련 기준을 개정할 필요가 있다. 그리고 신축배관 너트부분에 설치되는 수밀용 고무링 소재에 대해 세부적인 기준이 없어 NBR과 EPDM 소재가 함께 사용되고 있으나 수밀성이 우수한 EPDM 소재가 사용되도록 관련 기준을 개정할 필요가 있다.

• 시멘트
• /
• 통권47호
• /
• pp.69-73
• /
• 1972

본 시험은 현장에서 실시 가능한 간이식 측정 방법에 의하여 실시되었으며 pipe line의 점검, 보수 등의 불철저로 인한 air leakage량은 전체 압기 토출량의 12.42$\%$에 달하고 있다.

• Geomechanics and Engineering
• /
• 제16권4호
• /
• pp.423-433
• /
• 2018

A three-dimensional model is constructed to simulate water infiltration in an unsaturated slope from a leaking pipe. Adaptive mesh refinement and time stepping are used, assisted by an automatic procedure for progressive steepening of the hydraulic property function for better convergence. The model is justified by comparing the simulated results with experimental data. Steady-state flow is investigated considering various pipe water pressures, locations and sizes of the opening, and soil layering. The opening size significantly affects the soaked zone around the pipe. Preferential flow dominates along the pipe longitudinal direction in the presence of a loose backfill around the pipe.

• Journal of Welding and Joining
• /
• 제22권5호
• /
• pp.58-64
• /
• 2004

Although leakage at a low carbon steel pipe made by electrical resistance welding (ERW) was reported due to grooving corrosion, the cause for the corrosion has not yet been cleared. In order to clarify the main cause, failure analysis on the leaked pipe was carried out, followed by metallographic investigation and corrosion test for the various ERW pipe made with different welding heat input. The microstructure, particularly inclusion content, of the weldment is dependant on the welding heat input applied. For an improper low heat input, the amount of inclusion at the weld was high. High inclusion content accelerated grooving corrosion at the weld. It is therefore that welding heat input should be controlled based on the carbon content of the pipe in order to improve the corrosion resistance of the ERW pipe.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2007년도 춘계학술대회A
• /
• pp.7-10
• /
• 2007

In case of large steel water pipe, it have been observed that its fracture mostly occurs due to the complicated outside fatigue load on the pipe in the underground. It is also well known that its damage and leakage happen mainly in a weld zone. In this study we evaluated the fatigue characteristics based on size effect and residual stress by comparing the test results on the standard specimen collected from real pipe with those on full scale pipe.

• 제어로봇시스템학회:학술대회논문집
• /
• 제어로봇시스템학회 2000년도 제15차 학술회의논문집
• /
• pp.219-219
• /
• 2000

A Plate type pipe is used for heat exchange in radiator of a vehicle. The pipe has several rooms through which water flows and heat is dissipated into outside . In the case that there are small holes, cracks or some scratches on the plate, the radiators lost their functions due to Leakage. This may result in overheating of engine in a car. Thus, we need to perform the entire inspection of the plate type pipe in advance before assembling the radiator. In manufacturing process of the plate type pipe, the productive speed is very high and that may be performed continuously. So, there is no room to perform the outlook inspection by typical image processing techniques. This paper proposes a new method to inspect the outlook surface of the plate type pipe automatically with high speed. Especially, the sequential processing technique of an algorithm which detects defects on the surfaces of the plate type pipe is proposed for line scan camera which captures line image. To evaluate the inspection performance, a series of experiments is performed.

• 한국압력기기공학회 논문집
• /
• 제17권1호
• /
• pp.8-17
• /
• 2021

The seat leakage test is required after the maintenance work on the valve seat. Either the test has been performed outside of the plant after cutting the valve from the pipe system or the simplified test has been performed so far. It was unable to perform the test at the plant site because it is hard to make a steady pressure on the valve inlet when it is installed in the pipe. This research aims to perform the leakage test in the nuclear power plant while it is installed in the pipe system. The mock-up test is performed by pressurizing the leak-off pipe on the valve body. The result is compared with traditional test result by pressurizing the valve inlet. Furthermore the chamber mock-up tests are performed under various conditions. The leak rate by the developed test using the leak-off pipe is found to be similar but greater than the leak rate by the existing test method. It implies that the test using the leak-off pipe is more conservative than the existing test. The methodology and the equipment which this paper suggests that on-site seat test is possible and the application of the technology could reduce the time and cost for the valve maintenance work significantly.

• 한국화재소방학회논문지
• /
• 제30권3호
• /
• pp.55-61
• /
• 2016

본 연구는 현재 사용하고 있는 소방용 배관의 부식으로 인하여 발생하는 수계소화설비의 문제를 해결하기 위하여 개발한 Polyethylene (PE) 이종강관을 수계소화설비배관으로 적용할 수 있는지를 파악하기 위한 실제 화재시험을 수행하였다. 개발된 이종배관에 대한 관련시험기준이 없어 국내외 기술자료 및 시험기준을 비교분석하여 적합한 화재시험기준을 선정하여 PE 이종강관의 성능을 분석하였다. 따라서 본 배관의 성능시험에 채택한 화재시험기준은 합성수지배관과 금속배관의 두 가지의 화재시험기준을 적용하였고 총 6차례의 화재실험을 실시하여 배관성능을 평가하였다. 소방용합성수지배관의 시험기준을 적용한 1, 2차의 화재시험결과 이음쇠와 배관에서 파손이나 변형이 없었으며 5분간 내압시험을 실시한 결과에서도 누수가 없었다. 금속배관시험기준을 적용한 화재실험은 총 4회를 실시하였으며 1, 2차 실험은 습식설비를 모사한 것으로 화재시험결과는 PE 이종강관에서 누설이나 파열이 발생하지 않았으며 또한 PE 재질의 이탈 등 손상이 발생되지 않음을 확인하였다. 단, 건식설비를 모사한 3, 4차의 화재시험결과 소화수가 방출되기 이전에 PE 이종강관에서 파열, 변형 등의 손상이 발생하였다. 따라서 실험결과 습식설비를 모사한 화재시험의 경우 PE 이종강관의 융착성, 변형, 파손 등 배관의 성능에 이상이 없음을 확인하였다.

• Structural Engineering and Mechanics
• /
• 제84권3호
• /
• pp.337-344
• /
• 2022

Due to corrosion defects on the surface of the oil pipe, the sealing performance of the annular blowout preventer (BOP) decreases, and the leakage of toxic and harmful gases such as H₂S and SO₂ will threaten the safety of operators on the well. Therefore, this paper establishes the FE model for evaluating the sealing performance of BOP-oil pipe corrosion defects, which is based on the rubber large deformation theory and rubber core sealing mechanism, and designs the experiment of BOP sealing performance to verify the accuracy of the FE model. The sealing performance of BOP sealing oil pipe with corrosion defects is studied. The research results show that the sealing performance of BOP is more sensitive to the axial size of corrosion defects. With the increase of oil pipe outer diameter, the critical size of defects increases continuously. The sensitivity of radial and depth dimensions is low, When for 88.9 mm outer diameter oil pipe, the axial critical size of corrosion defect is 20 mm, the radial critical size is 16 mm and the critical depth is 2 mm. Fit the formula between the outer diameter of oil pipe and the piston increment. According to the formula, the operator can calculate the piston stroke increment required by the BOP to complete the sealing when the oil pipe is corroded.

• 한국기계가공학회지
• /
• 제14권3호
• /
• pp.43-49
• /
• 2015

This paper describes the design of a forged fitting form to acquire a method of product design measurement by target measurement standards. The pipefitting connects each pipe and combines seals and nipples with the pipes normally. Therefore, the section combined with the fitting pipe was measured by a 3D scanner, and the acquired measurement and the design measurement were obtained after modification of the forged fitting pipe by that standard. Moreover, the accuracy of the model was verified through leakage testing of the oil and verification of the design measurement for accuracy decisions on the design measurement after modification of the product.