• 대한기계학회논문집B
• /
• 제32권1호
• /
• pp.39-46
• /
• 2008

The loss coefficient of the butterfly valve which allows partial opening of the valve at closed position and is applicable to the small-sized pipe system with the diameter of 1 inch was measured for the variation of the valve disk blockage ratio. Two different types of the valve disk configuration to adjust the blockage ratio were considered. One was the solid type valve disk of which the diameter was changed into the smaller size rather than the pipe diameter, and the other was the perforate type valve disk on which some holes were perforated. The results from two types of valve disk were compared to identify their characteristics in the loss coefficient distributions. The loss coefficient and the controllable angle of the valve disk were decreased exponentially with the decrease of the blockage ratio. In addition, the perforate valve disk had the effect on the higher loss coefficient rather than the solid type valve disk.

• 대한기계학회논문집
• /
• 제6권3호
• /
• pp.211-221
• /
• 1982

Numerical analysis has been made on the heat transfer of two dimensional turbulent channel with a slat type blockage. Especially the effects of the height of slat and Reynolds number on the heat transfer characteristics of channel wall have been investigated. The methods of accelerating the convergence of the numerical solution of governing differential equation have been also examined. Line-by-line iterative method shows higher convergence rate than point-by-point iterative method for solution of both momentum equation and energy equation. The results show that the ratio of heat transfer coefficient of the wall near the blockage to that of the fully developed flow increase with increasing the ratio of blockage to channel height and decreasing the Reynolds number. These trends of variation of heat transfer coefficient with respect to the height of slat and Reynolds number agree with those of Sparrow's experiment on the pipe flow with slat type blockage.

• 한국유체기계학회 논문집
• /
• 제20권1호
• /
• pp.53-58
• /
• 2017

This paper describes liquidity evaluation on the horizontal branch pipe connected to a food waste disposer and performance of five disposers marketed. Experimental apparatus for analyzing the five disposers has been introduced to measure vibration, sound level and power consumption of the disposers. Simulator for analyzing the required water velocity to avoid waste jam inside the pipe connected to a food waste disposer has been designed and constructed. The simulator can control some experimental parameters: pipe slope, disposer supply water quantity, food waste materials and operation time of a disposer. Throughout the experimental measurements of the disposers marketed, it is found that the time need to crash food waste is about 20 seconds on the average. At the same flow condition, increase rate of internal water velocity is accelerated as the pipe slope increases. The water velocity inside the pipe having 50 A and slope of 1/50 is 0.26 m/s when the water flowrate to supply the disposer is 16 l pm. Considering the specific gravity and adhesion property of food waste, water velocity of the horizontal branch pipe connected to a food waste disposer need to excess 0.26 m/s at least to avoid the waste blockage inside the pipe.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2013년도 추계학술대회 논문집
• /
• pp.757-762
• /
• 2013

A technique is presented that uses a new guided wave technique for sludge and blockages detection in long-range pipelines. Existing techniques have the limitations that the sludge position needs to be known a priori and the area to be inspected needs to be accessible. Two guided wave techniques have been developed which allow the sludge or blockages to be detected remotely without the need to access the specific location where the pipe is blocked, nor to open the pipe. The first technique measures the reflection of guided waves by sludge which can be used to accurately locate the blocked region; the second technique detects sludge by revealing the changes to the transmitted guided waves propagating in the blocked region or after it. The two techniques complement each other and their combination leads to a reliable sludge or blockage detection. Various types of realistic sludge have been considered in the study and the practical capabilities of the two techniques have been demonstrated.

• 한국소음진동공학회논문집
• /
• 제23권3호
• /
• pp.282-290
• /
• 2013

A new method is presented that uses guided wave techniques for sludge and blockages detection in long-range pipelines. Existing techniques have the limitations that the sludge position needs to be known a priori and the area to be inspected needs to be accessible. Two guided wave techniques have been developed which allow the sludge or blockages to be detected remotely without the need to access the specific location where the pipe is blocked, nor to open the pipe. The first technique measures the reflection of guided waves by sludge which can be used to accurately locate the blocked region; the second technique detects sludge by revealing the changes to the transmitted guided waves propagating in the blocked region or after it. The two techniques complement each other and their combination leads to a reliable sludge or blockage detection. Various types of realistic sludge have been considered in the study and the practical capabilities of the two techniques have been demonstrated.

• 설비공학논문집
• /
• 제17권8호
• /
• pp.780-788
• /
• 2005

Two different types of algorithms were developed and applied to detect the partial faults of a multi-type air conditioning system. Partial faults include the compressor valve leakage, the refrigerant pipe partial blockage, the condenser fouling, and the evaporator fouling. The first algorithm was developed by using mathematical models and parity relations, and the second algorithm was developed by using mathematical models and a RBF neural network. Test results showed that the second algorithm was better than the first algorithm in detecting various partial faults of the system. Therefore, the algorithm developed by using mathematical models and a RBF neural network may be used for the detection of partial faults of an air-conditioning system.

• Journal of Advanced Marine Engineering and Technology
• /
• 제24권5호
• /
• pp.52-57
• /
• 2000

Recently large capacity of electric equipment and increasing in atomic power generation are shown. One of the reason is shortage of the electric power supply for air conditioning load during summer. And every consumer is concerning about economical refrigeration and air conditioning system to decreases electric power consumption and decrease in global warming. For these necessities, ice making thermal storage system is required. Therefore, in this paper, the possibility of continuous slurry ice making using flowing organic water solution in cooled circular tube has been investigated. The experiments was carried out under some parameters of concentration and velocity of water solution, temperature of cooled tube wall, and control pressure in tube, As a result, four types of operating conditions in the pipe, that was supercooling, continuous ice making, intermittent ice making and ice blockage, were classified . And it was found that the critical condition for continuous ice making was acquired as a function of these experimental parameters.

• 한국자동차공학회논문집
• /
• 제20권5호
• /
• pp.36-43
• /
• 2012

In this work the mixing and flow characteristics of a vane-type static mixer were investigated numerically for the reduction of NOx in the SCR-system of the diesel engines. The mixer was located in the 57 times pipe diameter away from the inlet. The analysis were performed by changing such various parameters as vane shape, angles, blockage ratio and location of the vane. The flow structure through the mixer was characterized by uniformity index and pressure drop. The results show that uniformity index and pressure coefficient are substantially influenced by the vane shape, angle, blockage ratio and position of the vane of the mixer.

• 한국산학기술학회논문지
• /
• 제16권4호
• /
• pp.2883-2890
• /
• 2015

준설토 이송의 효율을 증가시키기 위한 연구로써 전자기력을 배관에 인가하여 유동저항을 줄이고, 윤활 층에서의 유속을 침강 임계속도이상으로 증가시키어 침강으로 인한 폐색을 방지하는 기술을 개발하였으며, 이를 대규모 장거리 송토현장에 적용하기 위하여 송토 거리 500m 규모의 현장에서 그 영향을 검토하는 실험을 진행하였으며, 실험결과 유동효율 증대로 인한 송토 유량이 30% 이상 증가함을 실험을 통해 보였다. 이를 검증하기 위하여 전자기장 인가장치와 계측장비로 초음파 유속 프로파일러를 사용하여 배관 내 유속프로파일을 모니터링 하여 그 데이터를 비교분석하여 효과를 검증하였다.

• 한국철도학회:학술대회논문집
• /
• 한국철도학회 2010년도 춘계학술대회 논문집
• /
• pp.139-150
• /
• 2010

최근 한국에서는 세계적인 녹색기술을 맞아 향후 차세대 교통 시스템으로서 튜브 트레인 시스템의 본격적인 연구가 진행되고 있다. 한국 철도기술연구원(KRRI, Korea Railroad Research Institute)에서 튜브 트레인 시스템의 건설을 위한 목적으로 연구가 진행되고 있다. 본 논문에서는 기초연구의 일환으로 축대칭하며 긴 형상의 수송체가 가지는 다양한 튜브(터널) 내부의 압력, 막힘비율, 운행속도를 파라미터로 선정하여 전산해석을 수행하였다. 세부사항으로는 동일 형상의 운송체가 동일 운행속도를 가지고 일반적 압력의 개활지(오픈 시스템, 개활지 운행)를 운행할 때와, 다양한 환경(튜브 내 압력, 막힘비율, 운행속도)의 튜브 내부를 운행할 때에 대하여 튜브 트레인의 공력특성 연구를 수행하였다. 이를 통하여 다양한 운행속도-막힘비율 별로 개활지와 동일 에너지 효율 나오는 튜브 내 압력(P-D 관계)을 계산하였고, 막힘비율 증가에 따른 튜브 내 감압 정도(P-${\beta}$ 관계), 다양한 막힘비율-튜브 내 압력 별로 운행속도에 따른 전체 항력 양상(D-V 관계)을 보여 주었다. 그리고 개활지 운행시와 튜브 내부 운행시의 에너지 효율(주행저항)을 비교하였고, 튜브 내부 운행 시 트레인이 갖는 효율과 관계되는 충격파 발생의 임계속도(critical V-B 관계) 및 한계속도(V-P 관계)를 얻을 수 있었다. 이러한 연구의 결과는 튜브 시스템 설계 및 건설에 꼭 필요한 것이며 가이드라인을 제시했다.