• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2017.05a
• /
• pp.401-405
• /
• 2017

Continuous variable thrusters require precise thrust control to change the position or attitude of the aircraft and to control the pressure inside the combustion chamber. For this purpose, the thrust is adjusted by moving the pintle structure near the nozzle neck inside the combustion chamber by moving the pintle structure forward and backward, and the actuator is used to move the pintle structure. In this paper, we developed a actuator system for continuous variable thruster and load test system to simulate the load under operating conditions. Also, the performance test of the actuator was performed using the developed load test system

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.44 no.3
• /
• pp.247-255
• /
• 2016

The purpose of this study is to investigate unsteady-state characteristics of a pintle thruster with various pintle speed. Based on steady state experimental results, non-linear pintle stroke equation is obtained and applied to the unsteady state experimental system. For the unsteady state experiments, three different pintle speeds are used: 3.10 mm/s, 5.65 mm/s, 10.83 mm/s, respectively. Results show that backward pintle stroke results in faster convergence time because of high chamber pressure during backward pintle stroke sequence. During the forward and backward process, thrust curve shows singular points. These phenomenons is caused by variation of mass flow rate, which is mainly due to changes of both chamber pressures and nozzle throat area. This behavior becomes distinctive for a faster pintle speed case.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.48 no.12
• /
• pp.1033-1033
• /
• 2020

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.43 no.4
• /
• pp.304-310
• /
• 2015

Pintle thrusters use pintle stroke to change nozzle throat area, and this controls thrust. Using MATLAB, one-dimensional simulation has been investigated and the results are compared to those of cold flow tests and computational fluid dynamics for the pintle thruster of Chungnam National University. The prediction based on one-dimensional flow theory shows good agreement with measurements for chamber pressure, but deviates for thrust, partly because of nozzle wall separation. Computational results show that nozzle wall separation occurs at an early stage of nozzle expansion, near the design nozzle throat, for the course of pintle strokes. Empirical thrust prediction incorporates nozzle wall separation, and thus 1-D simulation using empirical thrust prediction showed good results for an early stage of pintle stroke.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2012.05a
• /
• pp.392-396
• /
• 2012

Experimental and computational study for steady-state pintle driven nozzle throat flow are carried out by changing four pintle shape. Results show that thruster performance is influenced by pintle shape greatly. This attributes to the distorted throat area and chamber pressure change as the pintle shape and its penetration.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2011.04a
• /
• pp.189-192
• /
• 2011

In solid rockets, a pintle thruster is a modulatable thrust device which controlls nozzle throat area. In this study, effect of bore on aerodynamic loads in a SNECMA modulatable thruster was carried out. Existence of bore resulted in reduced aerodynamic load.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.16 no.6
• /
• pp.62-72
• /
• 2012

Divert and attitude control system(DACS) plays an important role for orbit transfer and attitude control, and therefore becomes important subject for recent space vehicle and Precision Guided Missile(PGM) development. To develop DACS system, main research areas include shape combination of pintle and nozzle to maximize thrust change, and reduction of aerodynamic pintle load to minimizle pintle driving force, and development of multi-axis control algorithm. In this paper, introduction, classification, and overseas/domestic research and development program, and prospects of DACS are reviewed and summarized.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.18 no.5
• /
• pp.19-28
• /
• 2014

Firing test of solid rocket motor with pintle-technology carried out and the measured pressure-time curve was compared with the values predicted by the internal ballistic and performance analysis. Without baffle, the measured combustion chamber pressure was similar with the predicted pressure at the beginning of combustion, but gradual increase in pressure, which was unexpected with the end-burning grain of which burning area is constant, was observed. A baffle was inserted to make uniform flow over the pintle. Unlike the thruster without baffle, the measured combustion chamber pressure was 1.4 times higher than the predicted value. Through the CFD simulation, 10% of total pressure loss of the flow was observed from combustion chamber to nozzle throat when the baffle was inserted. The measured pressure with baffle was predicted well by considering the total pressure loss in the internal ballistic modelling and performance analysis.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.24 no.6
• /
• pp.69-77
• /
• 2020

A quasi one-dimensional multi-phase reaction flow analysis code is developed for the performance analysis of liquid pintle thrusters. Unsteady flow field, droplet evaporation, finite reaction and film cooling models are composed as the major models of the performance analysis. The droplet vaporization takes account of Abramzon's vaporization model, and the combustion employs a flamelet model based on detail chemical reactions. Shine's model is applied for the film cooling calculation. To verify each model, the Sod shock tube, single droplet vaporization, kerosene droplets combustion, and film length are evaluated.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2008.11a
• /
• pp.67-71
• /
• 2008

Rocket nozzle components and thrusters for next-generation solid rocket with variable thrust, and small uncooled liquid rocket thrusters are required to withstand ultra-high temperature upto $2500^{\circ}C$. In this survey, the operationg environments are investigated with the suggeations of proper materials and their fabrication methods. Especially, It is suggested that Rhenium and other competative matrials are exploited to $2500^{\circ}C$ hot components, and thus needed to be developed.