• Journal of the Korean Society of Propulsion Engineers
• /
• v.23 no.4
• /
• pp.28-34
• /
• 2019

In this study, pin-fin arrays, which are widely used for cooling turbine blades, were studied. The vortex generator in pin-fin arrays is located in front of the circular tube. The cross-section of the vortex generator is NACA-9410. The purpose of this study is to analyze heat transfer performance and flow characteristics of pin-fin arrays. The position of vortex generator is changed with the vertical flow direction on the bottom wall. Pin-fin arrays were calculated with 6000, 10000 and 15000 Reynolds number. The commercial program ANSYS v18.0 CFX and the turbulence model $k-{\omega}$ SST were used. As a result, the heat transfer performance increased up to 5.8% and pressure loss increased less than 1%.

• Journal of the Korean Society of Costume
• /
• v.60 no.3
• /
• pp.1-9
• /
• 2010

The purpose of this study is to develop Blue-Jean Design for Ideal Body Shape. The final aim of Fashion design is looks beauty of people by optical illusion. This study is based on Gestalt therapy and, is blue jeans design using optical illusion of vertical line for ideal beauty body image. Optical illusion for blue-jean design effect to achieve the ideal body shape. We can accumulate the preceding study for modern clothing from design and the related optical illusion effects. Vertical line stitches have all the advantages especially in pants design. I design blue jeans using optical illusion theory. The results of this study are as follows: First, Vertical line helps that jean has the long body shape effectively. Second, Jeans which have two or more vertical lines is more effective than simple Jean in order to make slim body shape. Third, Appropriate position of horizontal lines can be effective to make long body shape. Fourth, Top stitch, pin-tuck and pleats can be applied to vertical or horizontal lines instead of cutting lines.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.39 no.3
• /
• pp.245-251
• /
• 2015

In an electrical reliability test of a printed circuit board (PCB), the impact of the micro probing pins on the PCB needs to be checked to ascertain the quality of the circuit. In this study, the impact of the dynamic movement of the probing pin on the pad was observed. As a misaligned pin can exert horizontal force on the pad of the PCB, this study focused on the behavior of a misaligned probing pin. The parameters of observation were the circular and flat edges of the probing pin. The effects of the speed of movement, diameter, and the length of projection of the probing pin were also investigated. The results demonstrated that slippage angle is strongly affected by the shape of the edge of the probing pin, and that projection length is an important factor affecting pin slippage. In contrast, the speed of movement of the probing pin was able to double the slippage angle.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2003.05a
• /
• pp.443-447
• /
• 2003

The BEM (Boundary Element Method) is a computational technique for the approximate solution of problems in continuum mechanics. In the BEM both volume and surface integrals transformed into boundary integral equations. So, we applied the ECM (Electrochemical Machining) process to boundary problem, because our focus is only deformed shape. The ECM process is modeled as a two-dimensional problem assuming constant properties of electrolyte, and an incremental formulation is used with automatic mesh regeneration. As a result the final shape is roughly agreed with experimental shape. But, it has an error of exact shape, because a chemically factor is not considered

• Proceedings of the KWS Conference
• /
• 2006.05a
• /
• pp.103-105
• /
• 2006

• Journal of Biosystems Engineering
• /
• v.37 no.3
• /
• pp.201-208
• /
• 2012

Purpose: This study was conducted to develop a vegetable transplanting robot which transplants seedlings from a nursery tray to a plant pot using its four fingers. Method: The robot consists of the transplanting part, nursery tray moving part, plant pot moving part, main frame and controller. Two moving parts are controlled by the photo sensor and servo motor. The transplanting part was composed with two components; transporting device using E-MY2H(SMC Corp., Japan) for controlling finger position accurately and finger for transplanting the seedling. Results: Head lettuce using the transplanting robot was transplanted in 21 days after sowing based upon the seed shape measurement and removing examination. The optimal finger shape was thin pin type because it caused minimum damage to the roots of seedlings. Conclusions: The four inclined pin type was applied to remove the seedlings from the nursery tray. In addition, the transplanting capacity of the developed robot was 2800 pots per hour and the rate of success was 99% and above.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2002.04a
• /
• pp.25-28
• /
• 2002

Contact type Ic measurement system is needed to measure Ic continuously for long Bi-2223 tapes. Voltage and current terminals were designed several shapes for 4-probe method Ic measurement. Voltage terminals were made with brass and current terminals were made with Cu. We used 2 kinds of Bi-2223 tapes with different strength. When we measured Ic of Bi-2223 tape with Ag-Mg sheath, The proper weight was 0.3 kg and sharp pin type was better. according to voltage terminal shape and load. In case of Bi-2223 tape with Ag-Mn sheath, the proper terminal weight was 4 kg and sharp pin type was bad. It was possible to make continuous contact type Ic measurement system because We could get proper data - terminal shapes and loads - through these experiments.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.30 no.2 s.245
• /
• pp.95-100
• /
• 2006

Electrostatic precipitators(EPs) have low pressure drop and high dust collection efficiency and are widely used for industrial dust collectors. The current-voltage characteristics, which are important to maintain high dust collection efficiency, depend on several factor: discharge electrode shape, gas flow property, dust loading etc. In this study, experiments are performed to investigate the current-voltage characteristics of the corona discharge of various electrode geometries and an empirical model is proposed to predict current-voltage characteristics of the corona discharge. The corona onset voltage correction coefficient$(\alpha)$ and the geometry correction coefficient$(k_g)$ are used to the conventional equation for wire-plate type discharge electrode. The corona onset voltages are -6.3kV and almost constant when the numbers of discharge pins are varied from 3 to 9. The length of discharge pins has very sensitive effects on the corona onset voltage. They are increased from -6.3 to -7.8kV when the discharge pin length are 8.5 and 4.5mm, respectively. The empirical model shows good agreement with experimental results and can predict the effects of discharge pin length and number.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.17 no.6 s.109
• /
• pp.556-561
• /
• 2006

In this paper, a frequency reconfigurable slot antenna which has a bandwidth-enhanced characteristic is proposed. The proposed antenna consists of two parts; the wide slot and the narrow slot, to increase the bandwidth of the antenna and have the frequency reconfigurable characteristic. The wide slot has triangular shape and makes the bandwidth increased, and the narrow slot can mount PIN diodes. By changing on/off state of PIN diodes, the total length of the slot is changed. From this characteristic, the proposed antenna can finally control the center frequency and minimize variation of the impedance matching.

• Journal of the Korean Society of Manufacturing Technology Engineers
• /
• v.18 no.3
• /
• pp.270-278
• /
• 2009

Friction stir welding is a relatively new solid state joining process. A6061-T6 and A5052-H32 aluminium alloy has gathered wide acceptance in the fabrication of light weight structures requiring a high strength to weight ratio and good corrosion resistance. This friction stir process uses a non-consumable tool to generate frictional heat in the abutting surfaces. The welding parameters such as tool rotational speed, welding speed, etc., and tool pin profile play a major role in deciding FSP zone formation in A6061-T6 and A5052-H32 aluminium alloy. Three different tool pin profiles have been used to fabricate the dissimilar butt joints. The formation of friction stir processed zone has been analysed macroscopically. Tensile properties of the joints have been evaluated and correlated with the friction stir processed zone formation.