• Journal of the Korean Applied Science and Technology
• /
• v.12 no.1
• /
• pp.125-131
• /
• 1995

Ultra thin films of Tetra-3-hexadecylsulphamoylcopperphthalocyanine(HDSM-CuPc) were formed on various substrates by Langmuir-Blodgett method, where HDSM-CuPc was synthesized by attaching long-chain alkylamine(hexa-decylamine) to CuPc. The reaction product was identified with FT-IR, UV-visible absorption spectroscopies, elemental analysis and thin layer chromatography. The formation of Ultrathin Langmuir-Blodgett(LB) films of HDSM-CuPc was confirmed by FT-IR and UV-visible spectroscopies. A quartz piezoelectric crystal coated with LB films of HDSM-CuPc was examined as a gas sensor for $N0_2$ gas. HDSM-CuPc LB films were transferred to a quartz crystal microbalance(QCM) in the form of Z-type multilayers. Response characteristics of film-coated QCM to $NO_2$ gas concentrations over a range of $100{\sim}600ppm$ have been tested with a thickness of $5{\sim}20$ layers of HDSM-CuPc. Changes in frequency by adsorption of $NO_2$ were increased With the number of LB layers and $NO_2$ concentration, but the response time was slow.

• The Transactions of the Korean Institute of Electrical Engineers C
• /
• v.54 no.7
• /
• pp.308-314
• /
• 2005

The 2 GHz film bulk acoustic wave resonator(FBAR), one of the most necessary device of the next generation mobile communication system, consisted of solidly mounted resonator(SMR) structure using Brags reflector, was researched in this paper The FBAR applied SiO$_{2}$ and W had large difference of the acoustic impedance to reflector Al to electrode and ZnO to piezoelectric layer. Specially, the FBAR applied the two-step deposition method to improve the c-axis orientation and increase reproducibility of the fabrication device had good performance. The electrical properties of plasma such as impedance, resistance, reactance, $V_{pp},\;I{pp}$, VSWR and phase difference of voltage and current, was analyzed and measured by RF sensor with the variable experiment process factors such as gas ratio, RF power and base vacuum level about concerning the thickness, c-axis orientation, adhesion and roughness. The FBAR device about the optimum condition resulted reflection loss(S$_{11}$) of -17 dB, resonance frequency of 1.93 GHz, electric-mechanical coefficient(k$_{eff}$) of 2.38 $\%$ and Qualify factor of 580. It was seen better qualify than the common dielectric filter at present and expected on business to the filter device of 2 GHz bandwidth with the MMIC technology.

• The Journal of the Acoustical Society of Korea
• /
• v.16 no.2
• /
• pp.89-94
• /
• 1997

A new type SO$_2$ gas sensor with a particular inorganic thin film on SAW devices was developed. The sensor consisted of twin SAW oscillators of the center frequency of 54 MHz fabricated on the LiTaO$_3$ piezoelectric single crystal. One delay line of the sensor was coated with a CdS thin film that selectively adsorbed and desorbed SO$_2$, while the other was uncoated for use as a stable reference. Deposition of the CdS thin film was carried out by the spray pyrolysis method using an ultrasonic nozzle. The sensor could measure the concentration in air less than 0.25 parts per million of SO$_2$. Stability of the sensor turned out to be as good as less than 20ppm, recovery time after each measurement was as short as 5 minutes. Repeatability of the measurement was confirmed through so many reiterated experiments. Hence, the SAW sensor developed through this work showed promising performance as a microsensing tool of SO$_2$. Further work required to improve the performance of the sensor includes enhancement of the reactivity of the CdS thin film with SO$_2$ through appropriate dopant addition, an increase of the center frequency of the SAW device.

• 한국연소학회:학술대회논문집
• /
• 2005.10a
• /
• pp.104-109
• /
• 2005

This paper describes the effect of the split injection on combustion and emission characteristics in a common rail diesel engine at various operating conditions. The combustion pressures and exhaust emissions such as $NO_x$ and soot were measured at various split injection timings. The experimental apparatus of this study is composed of 4 cylinder engine installed with piezoelectric pressure sensor, EC dynamometer, and exhaust gas analyzer for the measurement of $NO_x$, CO, HC and soot emissions. Results show that the split injection has a great effect on reducing the rapid premixed combustion and $NO_x$ emissions.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.31 no.2 s.257
• /
• pp.202-207
• /
• 2007

In order to understand the phenomena of combustion instability, an experimental study was conducted at the moderate pressure and ambient temperature conditions. The flame behavior and the pressure fluctuations were measured in a dump combustor. Various types of combustion modes occurred in accordance with the equivalence ratio and the fuel supplying conditions. The fluctuation of pressure, heat release and equivalence ratio were measured by piezoelectric pressure sensor, high speed Intensified Charge Coupled Device (HICCD) camera and gas chromatography respectively. Two representative modes were self-excited pressure oscillations at the resonance of combustion chamber (200Hz) and instabilities related to the modulated fuel flow rate through the fuel holes (10Hz). It is found that, especially in an unchoked fuel flow condition, the modulation of the fuel flow rate affects the characteristics of flame behavior and pressure fluctuations in a lean premixed flame.

• Proceedings of the Korea Contents Association Conference
• /
• 2008.05a
• /
• pp.595-597
• /
• 2008

Zinc Oxide(ZnO) thin films on Si (100) substrate were deposited by RF magnetron sputter with changing sputtering conditions such as argon/oxygen gas ratios, RF power, and substrate temperature, chamber pressure and target-substrate distance. To analyze a crystallographic properties of the films, ${\Theta}/2{\Theta}$ mode X-ray diffraction, SEM analyses. C-axis preferred orientation highly depended on RF power.

• Proceedings of the Materials Research Society of Korea Conference
• /
• 2003.11a
• /
• pp.75-75
• /
• 2003

본 연구에서는 대기 중 극 미량으로 존재하는 환경 유해 가스 성분을 검출할 수 있는 미세 소자로의 응용을 위해 마이크로 칸티레버를 제작하고 가스 센서로의 활용 가능성을 검토하였다. 마이크로 칸티레버는 크게 구동층 캐패시터로서 대표적인 압전 재료인 Pb(Zr,Ti)O$_3$ (PZT)를 사용하고 SiNx 박막을 지지층으로 하는 형태로 제작되었다. 제작된 마이크로 칸티레버는 치수 및 형상에 따라 17~29 KHz 의 기본 공진 주파수 값을 나타내었다. Electron beam evaporator를 이용한 copper (Cu) 박막의 단계적인 증착을 통해 칸티 레버 표면에 질량을 증가시키고 그에 따른 마이크로 칸티레버의 공진주파수 변화를 관찰한 결과 질량 증가에 대해 34 Hz/ng의 선형적인 주파수 감소를 나타내었으며, 이로부터 694.4 $\textrm{cm}^2$/g 의 gravimetric sensitivity factor를 얼을 수 있었다. 마이크로칸티레버의 가스 감지능력 시험을 위해 가스 흡착층으로 일차 알콜류의 vapor를 흡착 하는 것으로 보고된 poly methyl metacrytate (PMMA)를 마이크로 칸티레버 표면에 코팅하였다. 마이크로칸티 레버의 기본 공진 주파수 및 PMMA 흡착층 형성과 가스의 흡착에 따른 주파수 변화는 마이크로 칸티 레버로부터 의 전기적 신호를 이용하는 복소 임피던스 분석에 의해 측정되었다. PMMA가 코팅된 마이크로 칸티레버는 ethanol 및 methanol vapor 의 농도가 증가함에 따라 선형적인 공진주파수 감소를 나타내었으며, methanol vapor 의 경우 0.06 Hz/ppm 의 가스 검출 감도를 얻을 수 있었다.

• Journal of Sensor Science and Technology
• /
• v.5 no.3
• /
• pp.25-31
• /
• 1996

Steel wires are made by elongating hot billets. If the billets have internal or surface defects, the wire can be broken during elongation process. After testing surface defect, we are testing internal defect by ultrasonic transducers. POSCO is producing two kinds of billets, hot rolled billet and cast billet. Hot rolled one is denser than cast billet. Because of the low density and rough surface, ultrasonic testing is difficult for the cast billet. Size of the transducer was related with the size and density of the billet. A transducer having 21mm long, 8.5mm wide and 0.95mm thick piezoelectric ceramic plate was best for $160mm\;{\times}\;160mm$ cast billet. Center frequency of the transducer was 2.25MHz and the focus distance was 70mm.

• Journal of the Microelectronics and Packaging Society
• /
• v.16 no.1
• /
• pp.13-19
• /
• 2009

A 440MHz wireless and passive surface acoustic wave (SAW) based chemical sensor was developed on a $41^{\circ}YX\;LiNbO_3$ piezoelectric substrate for simultaneous measurement of $CO_2$ gas and relative humidity (RH) using a reflective delay line pattern as the sensor element. The reflective delay line is composed of an interdigital transducer (IDT) and several shorted grating reflectors. A Teflon AF 2400 and a hydrophilic $SiO_2$ layer were used as $CO_2$ and water vapor sensitive films. The coupling of mode (COM) modeling was conducted to determine optimal device parameters prior to fabrication. According to simulation results, the device was fabricated and then wirelessly measured using the network analyzer. The measured reflective coefficient $S_{11}$ in the time domain showed high signal/noise (S/N) ratio, small signal attenuation, and few spurious peaks. In the $CO_2$ and humidity testing, high sensitivity ($2^{\circ}/ppm$ for $CO_2$ detection and $7.45^{\circ}/%$RH for humidity sensing), good linearity and repeatability were observed in the $CO_2$ concentration ranges of $75{\sim}375ppm$ and humidity levels of $20{\sim}80%$RH. Temperature and humidity compensations were also investigated during the sensitivity evaluation process.