• 한국결정성장학회지
• /
• 제21권6호
• /
• pp.225-229
• /
• 2011

현재 결정질 태양전지에서 웨이퍼 가공은 대부분 슬러리 분사 방식의 다중 와이어를 이용한 방법이 사용되고 있다. 이와 같은 슬러리 분사 방식의 웨이퍼 가공은 가공속도가 낮아 생산성이 떨어지는 단점이 있을 뿐만 아니라 금속 재질의 와이어와 실리콘 블록의 직접적인 마찰에 의하여 웨이퍼 표면의 금속 불순물에 의한 오염이 발생되는 단점이 있다. 뿐만 아니라 와이어와 실리콘 블록간의 직접적인 마찰로 인하여 와이어가 빨리 마모되며, 이로 인하여 일회성의 와이어를 사용하게 되면서 제조원가는 상승하게 된다. 반면에 다이아몬드 입자가 코팅된 와이어를 이용하여 실리콘 웨이퍼를 가공하게 되면, 가공속도가 기존 슬러리 분사방식보다 빠르며, 공정진행에 따른 와이어의 마모율이 적어 와이어의 재사용에 의한 제조원가 절감이 가능하다. 따라서 이와 같은 다이아몬드 입자가 코팅된 와이어를 이용하여 가공하는 기술은 슬러리 분사방식에 비하여 더 효율적이라 할 수 있다. 본 연구에서는 슬러리 분사방식으로 가공된 웨이퍼와 다이아몬드 코팅된 와이어로 가공된 웨이퍼의 표면특성에 대하여 분석하고 셀 공정에 영향을 미치는 것에 대하여 설명하고자 한다. 또한, 다이아몬드 와이어로 가공된 웨이퍼를 활용하기 위한 셀 공정의 개선방향에 대하여 제안하고자 한다.

• 한국전기전자재료학회논문지
• /
• 제36권4호
• /
• pp.332-340
• /
• 2023

Crystalline silicon solar cells have attracted great attention for their various advantages, such as the availability of raw materials, high-efficiency potential, and well-established processing sequence. Tunnel oxide passivated contact (TOPCon) solar cells are widely regarded as one of the most prospective candidates for the next generation of high-performance solar cells because an efficiency of 26% has been achieved in small-area solar cells. Compared to n-type TOPCon solar cells, the photo conversion efficiency (PCE) of p-type TOPCon is slightly higher. The highest PCEs of p-type TOPCon and n-type TOPCon solar cells are 26.0% and 25.8%, respectively. Despite the highest efficiency in small-area cells, limited progress has been achieved in p-type TOPCon solar cells for large are due to their lower carrier lifetime and inferior surface passivation with the boron-doped c-Si wafer. Nevertheless, it is of great importance to promoting the p-type TOPCon technology due to its lower price and well-established manufacturing procedures with slight modifications in the PERC solar cells production lines. The progress in different approaches to increase the efficiencies of p-type TOPCon solar cells has been reported in this review article and is expected to set valuable strategies to promote the passivation technology of p-type TOPCon, which could further increase the efficiency of TOPCon solar cells.

• Current Photovoltaic Research
• /
• 제9권3호
• /
• pp.75-83
• /
• 2021

The tunnel oxide passivated contact (TOPCon) structure got more consideration for development of high performance solar cells by the introduction of a tunnel oxide layer between the substrate and poly-Si is best for attaining interface passivation. The quality of passivation of the tunnel oxide layer clearly depends on the bond of SiO in the tunnel oxide layer, which is affected by the subsequent annealing and the tunnel oxide layer was formed in the suboxide region (SiO, Si₂O, Si₂O₃) at the interface with the substrate. In the suboxide region, an oxygen-rich bond is formed as a result of subsequent annealing that also improves the quality of passivation. To control the surface morphology, annealing profile, and acceleration rate, an oxide tunnel junction structure with a passivation characteristic of 700 mV or more (V_oc) on a p-type wafer could achieved. The quality of passivation of samples subjected to RTP annealing at temperatures above 900℃ declined rapidly. To improve the quality of passivation of the tunnel oxide layer, the physical properties and thermal stability of the thin layer must be considered. TOPCon silicon solar cell has a boron diffused front emitter, a tunnel-SiO_x/n⁺-poly-Si/SiN_x:H structure at the rear side, and screen-printed electrodes on both sides. The saturation currents J_o of this structure on polished surface is 1.3 fA/cm² and for textured silicon surfaces is 3.7 fA/cm² before printing the silver contacts. After printing the Ag contacts, the J_o of this structure increases to 50.7 fA/cm² on textured silicon surfaces, which is still manageably less for metal contacts. This structure was applied to TOPCon solar cells, resulting in a median efficiency of 23.91%, and a highest efficiency of 24.58%, independently. The conversion efficiency of interdigitated back-contact solar cells has reached up to 26% by enhancing the optoelectrical properties for both-sides-contacted of the cells.

• 한국태양에너지학회:학술대회논문집
• /
• 한국태양에너지학회 2011년도 춘계학술발표대회 논문집
• /
• pp.25-30
• /
• 2011

In this paper, we analyzed the electrical characteristics with Micro-cracks in Photovoltaic module. Micro cracks are increasing the breakage risk over the whole value chine from the wafer to the finished module, because the wafer or cell is exposed to mechanical stress. And The solar cells have to with stand the stress under out door operation in the finished module. Here the mechanical stress is induced by temperature changes and mechanical loads from wind and snow. So, we experimentally analyze the direct impact of micro-cracks on the module power and the consequences after artificial aging. The first step, we made micro-cracks in PV module by mechanical load test according to IEC 61215. Next, PV modules applied the thermal cycling test, because micro-cracks accelerated aging by thermal cycling test, according to IEC61215. Before every test, we checked output and EL image of PV module. As the result of first step, we detected little power loss(0.9%). But after thermal cycling test increased power loss about 3.2%.

• 한국태양에너지학회:학술대회논문집
• /
• 한국태양에너지학회 2009년도 추계학술발표대회 논문집
• /
• pp.350-355
• /
• 2009

The crysralline silicon solar cell where the solar cell market grows rapidly is occupying of about 85% or more high efficiency and low cost endeavors many crystalline solar cells. The fabricaion process of high efficiency crystalline silicon solar cells necessitate complicated fabrication processes and Ti/Pd/AG contact, This metal contacts have only been used in limited areas in spite of their good srability and low contact resistance because of expensive materials and process. Commercial solar cells with screen-printed solar cells formed by using Ag paste suffer from loe fill factor and high contact resistance and low aspect ratio. Ni and Cu metal contacts have been formed by using electroless plating and light-induced electro plating techniques to replace the Ti/Pd/Ag and screen-printed Ag contacts. Copper and Silver can be plated by electro & light-induced plating method. Light-induced plating makes use the photovoltaic effect of solar cell to deposit the metal on the front contact. The cell is immersed into the electrolytic plating bath and irradiated at the front side by light source, which leads to a current density in the front side grid. Electroless plated Ni/ Electro&light-induced plated Cu/ Light-induced plated Ag contact solar cells result in an energy conversion efficiency of 16.446 % on 0.2~0.6${\Omega}$ cm, $20{\times}20mm^2$, CZ(Czochralski) wafer.

• 한국전기전자재료학회논문지
• /
• 제35권6호
• /
• pp.616-621
• /
• 2022

Numerical simulation is a good way to predict the conversion efficiency of solar cells without a direct experimentation and to achieve low cost and high efficiency through optimizing each step of solar cell fabrication. TOPCon industrial solar cells fabricated with n-type silicon wafers on a larger area have achieved a higher efficiency than p-type TOPCon solar cells. Electrical and optical losses of the front surface are the main factors limiting the efficiency of the solar cell. In this work, an optimization of boron-doped emitter surface and front electrodes through numerical simulation using "Griddler" is reported. Through the analysis of the results of simulation, it was confirmed that the emitter sheet resistance of 150 Ω/sq along the front electrodes having a finger width of 20 ㎛, and the number of finger lines ~130 for silicon wafer of M6 size is an optimized technology for the front emitter surface of the n-type TOPCon solar cells that can be developed.

• 대한전자공학회논문지
• /
• 제13권2호
• /
• pp.23-27
• /
• 1976

p형과 n형 Si wafer의 111면위에 5x10-5mmHg의 진공내에서 SnO2-x박막을 Flash증착법으로 성장시킨 다음 산소분위기 속에서 열처리하여 Si-SnO2 heterojunction을 만들고 물성측정으로 부터 Energy bnad profile을 구하였다. 이 heterojunction은 양호한 정류성 Junction이며 400nm부터 1200nm까지 분광감도를 갖고 시정수가 -10-18sec로 고속광소자로 적합하며 Si p-n homojunction solar cell에 비하여 특성이 우수하고 제작이 간단하기 때문에 태양전지로 사용해도 손색이 없다. Si-SnO2 heterojunction was prepared by oxidzing at oxygen atmosphere SnO2-x Which made by Flith evaporation of SnO2 powder on III surface of p and n type Si single crystals. The energy band Profile of Si·SnO2 heterojunction was depicted from its physical properties. This heterojunction was very good rectifying junction, very sensitive in spectral response of Photovoltage at from 400nm to 1200nm, and -10-8sec of time contant. From above properties, this heterojunction was found ps good high speed photovoltaic device and solar cell.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2009년도 하계학술대회 논문집
• /
• pp.444-445
• /
• 2009

The metallic contact system of silicon solar cell must have several properties, such as low contact resistance, easy application and good adhesion. Ni is shown to be a suitable barrier to Cu diffusion as well as desirable contact metal to silicon. Nickel monosilicide(NiSi) has been suggested as a suitable silicide due to its lower resistivity, lower sintering temperature and lower layer stress than $TiSi_2$. Copper and Silver can be plated by electro & light-induced plating method. Light-induced plating makes use the photovoltaic effect of solar cell to deposit the metal on the front contact. The cell is immersed into the electrolytic plating bath and irradiated at the front side by light source, which leads to a current density in the front side grid. Electroless plated Ni/ Electro&light-induced plated Cu/ Light-induced plated Ag contact solar cells result in an energy conversion efficiency of 16.446 % on $0.2\sim0.6\;{\Omega}{\cdot}cm$, $20\;\times\;20\;mm^2$, CZ(Czochralski) wafer.

• Current Photovoltaic Research
• /
• 제12권2호
• /
• pp.37-40
• /
• 2024

One of the current innovation trends in the solar industry is the increase in the size of silicon wafers. As the wafer size increases, the series resistance of the module rises, highlighting the need for research on methods for cutting and bonding solar cells. Among these, the Infrared (IR) laser scribing technique has been extensively researched. However, there is still insufficient optimization research regarding the thermal damage caused by lasers on the Transparent Conductive Oxide (TCO) layer of Heterojunction (HJT) solar cells. Therefore, in this study, we systematically varied conditions such as IR laser scribing speed, frequency, power, and the number of scribes to investigate their impact on the performance of cut cells under each condition. Additionally, we conducted a comparative analysis of thermal damage effects on the TCO layer based on varying scribing depths.

• 한국전기전자재료학회논문지
• /
• 제25권5호
• /
• pp.345-348
• /
• 2012

The optical losses associated with the reflectance of incident radiation are among the most important factors limiting the efficiency of a solar cell. Therefore, photovoltaic cells normally require special surface structures or materials, which can reduce reflectance. In this study, nano-scale textured structures with anti-reflection properties were successfully formed on silicon. The surface of sicon wafer was etched by the inductively coupled plasma process using the gaseous mixture of $SF_6+O_2$. We demonstrate that the reflection characteristic has significantly reduced by ~0% compared with the flat surface. As a result, the power efficiency $P_{max}$ of the nano-scale textured silicon solar cell were enhanced up to 20%, which can be ascribed primarily to the improved light trapping in the proposed nano-scale texturing.