• 대한전자공학회논문지SD
• /
• 제46권2호
• /
• pp.9-14
• /
• 2009

본 연구에서는 sapphire 기판위에 P (phosphorus) 도핑된 ZnO 박막을 제작한 후, 산소 분위기에서 후열 처리 온도가 박막의 전기적 및 광학적 특성에 미치는 영향에 대해서 조사하였다. XRD 측정 결과, 후열 처리 온도에 무관하게 모든 박막이 c축 배향성을 나타내었다. Hall 측정 결과, $850^{\circ}C$에서 후열 처리한 박막에서만 p형 전도 특성이 관찰되었다. 이때의 홀 캐리어 농도와 홀 이동도는 각각 $1.18{\times}1016cm^{-3}$과 $0.96cm^2/Vs$의 값을 나타내었다. 저온 PL 측정 결과, $850^{\circ}C$에서 후열 처리한 박막의 경우 p형 특성을 나타내는 상당량의 억셉터가 관련된 A0X (3.351eV), FA(3.283eV) 및 DAP (3.201eV) 피크가 관찰되었다. 향후 P 도핑된 ZnO 박막의 공정 조건과 후열 처리 조건을 최적화시킨다면, 차세대 광소자에 응용될 수 있는 매우 유망한 재료로 주목받을 것으로 기대된다.

• Bulletin of the Korean Chemical Society
• /
• 제35권8호
• /
• pp.2357-2360
• /
• 2014

Phosphorus-doped soft carbons were successfully prepared by carbonizing petroleum cokes treated with phosphorus acids, such as $H_3PO_2$, $H_3PO_3$, and $H_3PO_4$. The effect of the type of phosphorus acids used on the composition, structure, and electrochemical performance of the soft carbons was extensively investigated. The soft carbons modified with $H_3PO_3$ and $H_3PO_4$ exhibited dramatically improved reversible capacities and outstanding rate capabilities.

• Current Photovoltaic Research
• /
• 제4권2호
• /
• pp.31-41
• /
• 2016

n-type PERT (passivated emitter, rear totally diffused) bifacial solar cells with boron and phosphorus diffusion as p+ emitter and n+ BSF (back surface field) have attracted significant research interest recently. In this work, the influences of wafer thickness, bulk lifetime, emitter, BSF on the photovoltaic characteristics of solar cells are discussed. The performance of the solar cell is determined by using one-dimensional solar cell simulation software PC1D. The simulation results show that the key role of the BSF is to decrease the surface doping concentration reducing the recombination and thus, increasing the cell efficiency. A lightly phosphorus doped BSF (LD BSF) was experimentally optimized to get low surface dopant concentration for n type bifacial solar cells. Pre-oxidation combined with a multi-plateau drive-in, using limited source diffusion was carried out before pre-deposition. It could reduce the surface dopant concentration with minimal impact on the sheet resistance.

• 대한전자공학회논문지
• /
• 제22권2호
• /
• pp.97-105
• /
• 1985

PECVD 방법으로 만들어진 도핑한 박막에서 실리콘으로의 인이나 붕소의 확산 특성이 연구되었다. CVD PSC 박막도 역시 만들어면 PECVD PSG에 있는 인의 확산특성과 나란히 비교되었다. 인의 부산은 N2와 O2 분위기 및 1000℃, 1,050℃, 1,100℃의 온도에서 수행되었다. 붕소의 확산 변수들은 B2H2유량 및 박막형성 온도를 달리하여 만들어진 박막에 관하여 고찰되었다. 실리콘으로의 주입물 확산 계수와 확산 Profile이 측정된 혹산 깊이 및 불순물 표면 농도를 써서 Barry의 모델을 적용하여 계산되었다.

• 대한전자공학회논문지
• /
• 제25권11호
• /
• pp.1342-1349
• /
• 1988

플리즈마 변수로서 가스조성과 압력 및 RF 전력이 인 및 붕소가 각각 다른 양으로 주입된 다결정 실리콘의 식각율 변화에 미치는 영향을 고찰하였다. $POCl_3$에 의해 인이 주입된 경우, 염소조성보다 불소조성이 많은 영역, 즉 $Cl_2$와 $SF_4$의 비가 17대 33일 때, 가장 큰 비등방성과 가장 작은 선폭손실을 달성하였다. 플라즈마 조건에 관계없이 주입된 불순물 농도의 증가에 다라, 인이 주입된 경우는 식각율이 증가하였고, 붕소가 주입된 경우는 식각율이 반대로 감소하였다. 또한, 급속 열처리에 의한 활성화 시간의 함수로서 인이 주입된 다결정실리콘의 식각율변화를 측정한 결과, 도우핑 농도뿐 아니라 활성화된 운반자, 즉 전자의 농도가 그 식각율 증가에 중요한 역할을 한다는 것을 확인하였다.

• 한국신재생에너지학회:학술대회논문집
• /
• 한국신재생에너지학회 2011년도 춘계학술대회 초록집
• /
• pp.122.1-122.1
• /
• 2011

Phosphorus is known to pile-up at the silicon surface when it is thermally oxidized. A thin layer, about 40nm thick from the silicon surface, is created containing more phosphorus than the bulk of the emitter. This layer has a gaussian profile with the peak at the surface of the silicon. In this study the pile-up effect was studied if this layer can act as a front surface field for solar cells. The effect was also tested if its high dose of phosphorus at the silicon surface can lower the contact resistance with the front metal contact. P-type wafers were first doped with phosphorus to create an n-type emitter. The doping was done using either a furnace or ion implantation. The wafers were then oxidized using dry thermal oxidation. The effect of the pile-up as a front surface field was checked by measuring the minority carrier lifetime using a QSSPC. The contact resistance of the wafers were also measured to see if the pile-up effect can lower the series resistance.

• 전자공학회논문지A
• /
• 제33A권3호
• /
• pp.126-134
• /
• 1996

Tungsten silicide films were deposited on the phosphorus-doped poly-Si/SiO$_{2}$/Si-substrates by LPCVD (low pressue chemical vapor deposition). The formation and various properties of tungsten silicide processed by furnace annealing in N$_{2}$ ambient were evaluated by using XRD. AFM, 4-point probe and SEM. And the redistribution of phosphorus atoms has been observed by SIMS. The crystal structure of the as-deposited tungsten silicide films were transformed from the hexagonal to the tetragonal structure upon annealing at 550.deg. C. The surface roughness of tungsten polycide films were found to very smoothly upon annelaing at 850.deg. C and low phosphorus concentration in polysilicon layer. The sheet resistance of tungsten polycide low phosphorus concentration in polysilicon layer. The sheet resistance of tungsten polycide films are measured to be 2.4 .ohm./ㅁafter furnace annealing at 1100.deg. C, 30min. It was found that the sheet resistance of tungsten polycide films upon annealing above 1050.deg. C were independant on the phosphorus concentration of polysilicon layer and furnace annealing times. An out-diffusion of phosphorus impurity through tungsten silicide film after annealing in $O_{2}$ ambient revealed a remarkably low content of dopant by oxide capping.

• Current Photovoltaic Research
• /
• 제7권4호
• /
• pp.125-129
• /
• 2019

Recently, carrier-selective contact solar cells have attracted much interests because of its high efficiency with low recombination current density. In this study, we investigated the effect of phosphorus doped amorphous silicon layer's characteristics on the passivation properties of tunnel oxide passivated carrier-selective contact solar cells. We fabricated symmetric structure sample with poly-Si/SiOx/c-Si by deposition of phosphorus doped amorphous silicon layer on the silicon oxide with subsequent annealing and hydrogenation process. We varied deposition temperature, deposition thickness, and annealing conditions, and blistering, lifetime and passivation quality was evaluated. The result showed that blistering can be controlled by deposition temperature, and passivation quality can be improved by controlling annealing conditions. Finally, we achieved blistering-free electron carrier-selective contact with 730mV of i-Voc, and cell-like structure consisted of front boron emitter and rear passivated contact showed 682mV i-Voc.

• 한국표면공학회지
• /
• 제27권4호
• /
• pp.234-240
• /
• 1994

A large area impurity doping method for poly-Si TFT LCD has been developed. The advantage of this method is the doping of impurities into Si over a large area without mass separation and beam scanning. Phosphorus diluted in hydrogen was discharged by RF(13.56MHz) power and ions from discharged gas were accelerated by DC acceleration voltage and were implanted into deposited Si films. The annealing characteristic of this method was similar to that of the ion implantation method in the low doping concentration. Three mechanisms were evolved in the annealing characteristics of phosphorus doped Si films. Point defects annihilation and the retrogradation of dopant atoms at grain boundaries as a result of grain growth played a major role at low and high annealing temperature, respectively. However, due to the dopant segregation, the reverse annealing range existed at intermediate annealing temperature.

• 한국진공학회:학술대회논문집
• /
• 한국진공학회 2014년도 제46회 동계 정기학술대회 초록집
• /
• pp.491.1-491.1
• /
• 2014

Heteroatom phosphorous-doped graphene aerogel (PGA) with high surface area is successfully synthesized via hydrothermal method for high power and energy supercapacitors, including the advantage of three dimensional internetwork and constitutive graphene skeletons. The morphology of PGA was investigated by the scanning electron microscope, transmission electron microscope. The chemical structure and circumstances were confirmed by Raman and X-ray photoelectron spectroscopy, the phosphorus is successfully incorporated with the graphene sheets. As evidenced by electrochemical measurements, cyclic voltammetry and galvanostatic charge discharge, the hierarchically PGA has an unprecedented high capacitance, which contributes to the excellent high-rate performance of this material for supercapacitor application.