• 대한전기학회논문지
• /
• 제36권10호
• /
• pp.741-747
• /
• 1987

The high-power Nd:glass system with five-stage amplifier was designed and its amplification characteristics was studied for developing high-power Nd:glass laser system as an energy driver of inertial confinement fusion(ICF). In order to study the amplification characteristics of remporal and spacial Gaussian laser beam, the dependence of them on pumping efficiency and rod loss were studied and discussed. The output energy of this system using phosphate Nd glass rod(LHG-7,LHG-8) and silicate Nd glass rod(LSG-91H), respectively, was calculated by the computer simulation using Avizonis-Grotbeck and Frantz Nodvik equations. As results of this simulation, it was found that the shorter the risetime of laser pulse, the larger the amplification factor and that the larger peak value of laser pulse, the lower the amplification factor. The output inergies of 179J, 344J, and 7J were obtained by the designed five-stage amplified high-power Nd:glass laser system using glass rods of LHG-7,LHG-8, and LSG-91H, respectively. From the results it was found that the laser system using the LHG-8 glass rod was the most excellent one among the systems and the cross section for stimulated emission of the gain coefficient was essentially important parameter for the amplification characteristics.

• 한국세라믹학회지
• /
• 제53권6호
• /
• pp.700-706
• /
• 2016

Etch rate, surface roughness and microstructure as plasma resistance were evaluated for six kinds of oxide glass with different compositions. Borosilicate glass (BS) was found to be etched at the highest etch rate and zinc aluminum phosphate glass (ZAP) showed a relatively lower etch rate than borosilicate. On the other hand, the etching rate of calcium aluminosilicate glass (CAS) was measured to be similar to that of sintered alumina while yttrium aluminosilicate glass (YAS) showed the lowest etch rate. Such different etch rates by mixture plasma as a function of glass compositions was dependent on whether or not fluoride compounds were formed on glass and sublimated in high vacuum. Especially, in view that $CaF_2$ and $YF_3$ with high sublimation points were formed on the surface of CAS and YAS glasses, both CAS and YAS glasses were considered to be a good candidate for protective coating materials on the damaged polycrystalline ceramics parts in semi-conductor and display processes.

• 한국재료학회지
• /
• 제19권12호
• /
• pp.657-660
• /
• 2009

Optical characteristics and structural changes depending on CuO content in phosphate glasses that are used in near-infrared (near-IR) filters were investigated. With phosphate glasses that contain 1-9 mol% CuO, changes in optical transmittance, optical absorption, and color coordinate were measured with a UV-VIS spectrophotometer. An XPS (X-ray photoelectron spectroscopy) analysis was performed to determine valence of copper ion that influences optical characteristics in near-IR filter glasses. Structural changes in glasses depending on CuO content were also analyzed by FT-IR (Fourier transform infrared) and Raman spectrophotometers. From the UV-VIS spectrophotometer results, strong absorption peaks at 220 & 900 nm were found and transmittance was decreased. The color coordinates of the glasses were shifted to the green color direction with CuO addition for increasing absorption of long wavelength range spectra, in spite of the amount of $Cu^{2+}$, which gives a blue color to glasses, and which was increased in XPS results. Also, structural de-polymerization of glasses with CuO addition were found by FT-IR and Raman results.

• 한국세라믹학회지
• /
• 제54권5호
• /
• pp.400-405
• /
• 2017

$P_2O_5-ZnO-SiO_2-R_2O$ glasses were synthesized as a sealing material for large scale dye-sensitized solar cells (DSSC). Compositional effects of $P_2O_5$ and ZnO were examined by varying their contents. Their viscosity and glass stability at sintering temperatures of less than $550^{\circ}C$ were examined by flow button test. Glass transition temperature and structural change upon compositional change were investigated. Chemical stability against electrolyte was also examined by immersing the glasses in the electrolyte for 72 h at $85^{\circ}C$.

• 한국광학회지
• /
• 제3권4호
• /
• pp.222-226
• /
• 1992

$Ar^{+}$레이저로 펌핑되는 Nd:glass레이저를 제작하여 그 특성을 조사하였다. 레이저 공진기는 오목거울 두 개와 98% 고반사 평면경, 그리고 Brewster 각도로 놓인 Nd:glass 의 이득 매질로 구성되었으며, 효율적인 펌핑을 위해서 $Ar^{+}$레이저 광선을 공진기 길이 방향으로 입사하여 공진모우드의 beam waist에서 초점이 맺히도록 하였다. Nd:glass의 열존도도가 작아서 흡수된 펌핑빔에 의해 생성된 잔열로 인한 매질의 손상이 우려되기 때문에 mechanical chopper 로 펌핑빔을 100Hz로 끊어서 입사하여 잔열의 생성을 줄였다. 1.5W로 펌핑될 때 Nd:glass 레이저의 출력은 70mW이었고 발진이 되는 문턱에서의 펌핑파워는 520mW이었으며 slope efficiency는 7.4%이었다.

• 한국전기전자재료학회논문지
• /
• 제28권9호
• /
• pp.571-576
• /
• 2015

In this study, we developed a lead-free $P_2O_5-V_2O_5-ZnO$ glass frit for sealing OLED using laser irradiation. The frit satisfied the characteristics required for laser sealing such as low glass transition temperature, low coefficient of thermal expansion (CTE), high water-resistance, and high absorption at the wavelength of the laser beam. Ceramic fillers were added to the glass frit in order to further reduce and match its CTE with that of the commercial glass substrate. The addition of Zirconium Tungsten Phosphate (ZWP) to the frit yielded the most desirable results, reducing the CTE to $45.4{\times}10^{-7}/^{\circ}C$, which is very close to that of the glass substrate ($44.0{\times}10^{-7}/^{\circ}C$). Successful formation of a solid sealing layer was observed by optical and scanning electron microscopy.

• 한국세라믹학회지
• /
• 제39권2호
• /
• pp.194-198
• /
• 2002

$K_2O{\cdot}CaO{\cdot}P_2O_5$를 기본조성으로 하여 용융법에 의해 유리 형성범위를 정의하고자 하였다. TG-DTA와 DSC를 이용하여 열적 특성을 관찰하고자 하였으며, FT-IR과 Raman Spectroscopy를 이용하여 구조를 분석하였다. $K_2O{\cdot}CaO{\cdot}P_2O_5$의 함량이 증가함에 따라 유리전이온도 및 연화온도는 감소하였다. $K_2O{\cdot}CaO{\cdot}P_2O_5$ 유리의 기본 구조는 이웃한 구조와 상호 결합을 위한 $PO_2$와 $PO_4^{3-}$ 구조와 유리의 골격구조를 이루는 P-O-P 결합이며, CaO의 함량이 증가함에 따라, 유리내의 P-O-P의 결합력은 점차적으로 증가하였으며, $PO_2$와 $PO_4^{3-}$의 intensity는 점차적으로 감소하였다.

• 대한심미치과학회지
• /
• 제8권1호
• /
• pp.76-82
• /
• 1999

Zinc phosphate cement has long been the material of choice for permanent luting of cast restorations, and through many years of use has been considered effective to retain castings. However, cast restorations cemented with this material have been susceptible to secondary caries. Glass ionomer luting agents become available in the late 1970s. These material s, through release of fluoride, show considerable promise as a means of reducing secondary caries. Other favorable traits include significantly less disintegration in vivo than zinc phosphate cements, a film thickness comparable to that of zinc phosphate cement, and adhesion to tooth structure. Compomer materials were created in 1993 as a filling material for deciduous teeth, cervical lesions, and class III cavities. In the meantime, compomer have been developed as chemical hardening cements for cast gold restorations. The aim of this paper is to review the articles on luting cements to help the choice of dental cements.

• 한국세라믹학회지
• /
• 제26권4호
• /
• pp.559-567
• /
• 1989

Bioglasses have been known to be as one of the promising biomateials, which can be used for replacing defective hard and soft tissue. There have been many reports on biological results for this type of glass, but no systematic work has carried out on the structures and properties of the bioglass itself. In the present study, the effect of P2O5 in bioglasses on their structures and properties was examined. Infrared and Raman spectroscopy for the glass structural analysis, differential thermal and X-ray diffraction analysis for the crystallization of the bioglass were performed, and several physical properties were measured. When the glasses were heat-treated, Na2O.2CaO.3SiO2 was the major crystalline phase and $\beta$-NaCaPO4 crystal was found for the glass with high P2O5 content. The added P2O5 in the glasses enhanced the polymerization of silicate glass structure and it changed the chain-like glass structure to a sheet-like structure, and some P2O5 may stay as phosphate monomer. With addition of P2O5 in the glass the density of the glasses decreased, but not much changes in their thermal expansion coefficient, softening point and microhardness were observed.

• 대한치과교정학회지
• /
• 제28권5호
• /
• pp.689-698
• /
• 1998

법랑질의 표면처리에 따른 광중합형 글래스아이오노머 시멘트의 전단결합강도를 알아보고자 사람 소구치 80개를 선택하여 8개군으로 나누어 전단 결합 강도를 측정하고, 접착 파절의 양상을 평가하여 다음과 같은 결과를 얻었다. $1.37\%$ 인산용액으로 부식한 후 건조상태에서 글래스아이오노머 시멘트, 광중합형 레진, 화학중합형 레진으로 각각 부착한 실험군에서 글래스아이오노머 시멘트 실험군의 전단결합강도는 두 군과 유의한 차가 없었으나 화학중합형 레진군의 그것은 광중합형 레진군에 비해 유의성있게 낮았다 (p<0.05). $2.37\%$ 인산 실험군, $10\%$ 폴리 아크릴산 실험군, $1.23\%$ APF 실험군, 산처리하지 않은 실험군의 습한 상태에서 부착한 글래스아이오노머 시멘트의 전단결합강도에서 산처리하지않은 실험군의 그것이 유의성 있게 낮았으며, 그 외 군간에는 유의성 있는 차이가 없었다 (p<0.05). 3. 글래스아이오노머 실험군에서 습기의 존재가 전단결합강도에 유의성 있는 영향을 미치지 않았다 (p<0.05). 4. 산부식처리를 하지않은 군의 접착제 잔류지수가 가장 낮았으며 $37\%$인산용액으로 처리한 군의 접착제 잔류지수가 가장 높았다.