• Journal of Periodontal and Implant Science
• /
• v.43 no.6
• /
• pp.291-300
• /
• 2013

Purpose: Calcium phosphate (CaP)-coated implants promote osseointegration and survival rate. The aim of this study was to (1) analyze the dissolution behavior of the residual CaP particles of removed implants and (2) evaluate bone apposition of CaP-coated machined surface implants at the early healing phase. Methods: Mandibular premolars were extracted from five dogs. After eight weeks, the implants were placed according to drilling protocols: a nonmobile implant (NI) group and rotational implant (RI) group. For CaP dissolution behavior analysis, 8 implants were removed after 0, 1, 2, and 4 weeks. The surface morphology and deposition of the coatings were observed. For bone apposition analysis, block sections were obtained after 1-, 2-, and 4-week healing periods and the specimens were analyzed. Results: Calcium and phosphorus were detected in the implants that were removed immediately after insertion, and the other implants were composed mainly of titanium. There were no notable differences between the NI and RI groups in terms of the healing process. The bone-to-implant contact and bone density in the RI group showed a remarkable increase after 2 weeks of healing. Conclusions: It can be speculated that the CaP coating dissolves early in the healing phase and chemically induces early bone formation regardless of the primary stability.

• Journal of Pharmaceutical Investigation
• /
• v.37 no.3
• /
• pp.193-196
• /
• 2007

This study aimed to evaluate and develop $Eudragit^{(R)}$-coated pellets based on the dissolution using the paddle method. As coating materials, two types of $Eudragit^{(R)}$ were applied to obtain either sustained release form or fast released form. The dissolution test was carried out in phosphate buffer solution (pH 6.5) at $37^{\circ}C$, 100 rpm. In order to develop a sustained release preparation containing felodipine, a comparative dissolution study was done using commercial product as a control. The dissolution at 30 min of felodipine from $Eudragit^{(R)}$ RS or RL-coated pellets were 0.96% and 99.65, respectively. The weight ratio of $Eudragit^{(R)}$ RL pellets to RS pellets altered the dissolution rate, but did not optimize the dissolution rate. However, the sustained dissolution of felodipine from pellets was optimized by varying the coating ratios of $Eudragit^{(R)}$ RS. It is suggested that the coating ratio of pellets is the main factor which controls dissolution rate. Taken together, $Eudragit^{(R)}$ RS 30D-coated pellets showed the most comparable dissolution rate pattern to commercial product, $Splendil^{(R)}$. This sustained release pellets for oral delivery system of felodipine was simply manufactured, and drug release behavior was highly reproducible.

• Journal of the Korean Applied Science and Technology
• /
• v.38 no.6
• /
• pp.1678-1686
• /
• 2021

In this study, we prepared phosphorous flame-retarding coating solutions by mixing triphosphate (3 phosphonate), phytic acid (6 phosphonate), or ammonium polyphosphate (10 phosphonate) with boric acid as a crosslinking agent and acryl resin binder. Prepared phosphorous flame-retarding coating solutions were coated onto non-woven fabrics, respectively, to obtain high flame-retarding effects. These prepared flame-retardant non-woven fabrics were evaluated using smoke density standard test (ASTM E662), limit oxygen index standard test (ISO E622), and vertical burning standard test (UL 94). Their flame-retarding effects were affected by the number of phosphonate groups. Regardless of natural or synthetic binder resins, their effects showed the following order: ammonium polyphosphate > phytic acid > triphosphate. Natural hydrocarbon compounds were also examined to determine the possible retardancy of binder resins. Results showed that natural hydrocarbon binder resins could be used for preparing fire-retardant nonwoven fabrics.

• Applied Chemistry for Engineering
• /
• v.16 no.2
• /
• pp.250-256
• /
• 2005

Coating appearance is the most important problem in automotive industry. To increase the coating appearance quality, the corrosion resistance and the coating adhesion on metal substrates must be basically solved. The phosphating film made by the pretreatment of metal substrate is important factor to increase the coating adhesion. During the cathodic electrodeposition, the pH at the cathode surface increases up to about 12. In such a highly alkaline condition, the dissolution of metal substrate and phosphate film occurs. These phenomena result in the decrease of the bonding strength between the phosphating film and the substrate. Generally, the structure of zinc phosphating film is hopeite or phosphophyllite. It has been known that the phosphophyllite film contains better corrosion resistance and paint adhesion for hot water immersion test because of the decrease of dissolving amount of both metal substrate and phosphating film during the cathodic electrodeposition. It is found that the addition of Ni and Mn composition increase P-ratio and then can improve the paint adhesion on metal surface and the corrosion resistance.

• Proceedings of the Materials Research Society of Korea Conference
• /
• 2003.11a
• /
• pp.147-147
• /
• 2003

탄소/탄소 복합체의 내산화 코팅을 위하여 산화티탄, 산화알루미늄, 산화이트륨 등을 포함하는 여러 가지 인산염계 유리를 제조하였다. 유리 산화물조성 몰비는 인산에 대하여 인산알루미늄을 15몰%, 30몰%, 45몰%로 하였고 산화티탄은 70몰%, 산화 이트륨은 25몰%이 되도록 코팅 액을 제조하였다. 제조 된 코팅액은 석영 도가니에서 열처리 하여 급냉 시켰으며, 급냉 시키고 다시 130$0^{\circ}C$, 1시간 동안 열처리하여 유리를 제조하였다. 제조된 유리의 열중량, 열팽창율, 열전도도를 분석하여 탄소 복합체와의 적합성을 조사하고, 내산화성 시험을 위해 탄소/탄소 복합체에 코팅액을 도포하여 산화 감량 비율을 측정하였다. 엑스선 회절분석기와 적외선 분광기를 통하여 인산염 유리의 구조분석을 실시하고 비커스 미세 경도 시험기를 이용하여 기계적 물성을 측정하였다.

• Journal of the Korean Society for Heat Treatment
• /
• v.10 no.3
• /
• pp.165-171
• /
• 1997

Laser hardening for the piston ring groove of ductile cast iron was tried. Mechanical and microstructural investigation for the hardened area indicated that the laser heating technique could replace conventional induction hardening process completely and further showed that post grinding process would be eliminated by minimizing bulging of heat treated area. In laser hardening, the volume increase caused by martensitic phase transformation proved to be less than $10{\mu}m$, which insures no post machining on the hardened surface. As expected, the depth of hardening was inversely proportional to the beam scanning velocity and the highest surface hardness was obtained at the beam velocity of 0.75m/min. Heat treatment using phosphate coating demonstrated quite comparable result to the case of graphite suscepter.

• Proceedings of the Korean Institute of Surface Engineering Conference
• /
• 2015.11a
• /
• pp.195-195
• /
• 2015

본 연구에서는 인산-망간 피막처리 공정 중에 생성되는 슬러지를 방지하기 위하여 인산-망간 화성처리액에 유기첨가제인 Tartaric acid를 첨가하여 내마모성 및 방청성 향상을 목적으로 슬러지를 방지하기 위한 인산-망간 화성피막의 특성을 연구하였다. Tartaric acid의 농도에 따른 표면 Morphology를 Scanning Electron Microscope (SEM)과 Energy Dispersive X-ray spectroscopy (EDS)을 이용하여 분석하였으며, EDS 분석을 통해 Mn, P, Fe, O, C의 성분을 확인 할 수 있었으며, 인산-망간 화성피막의 상(phase)을 확인하기 위하여 X-ray diffraction (XRD)을 분석을 통하여 $(Mn,Fe)_5H_2(PO_4)_44H_2O$으로 구성된 인산-망간 화성피막을 확인할 수 있었다. 또한 Tartaric acid의 농도에 따른 인산-망간 피막의 내마모 시험(Ball on disc) 및 경도시험을 실시하여 기계적인 특성 및 슬러지의 양에 대하여 분석하였다.

• The Korean Journal of Ceramics
• /
• v.4 no.4
• /
• pp.372-376
• /
• 1998

Using calcium-phosphate-powder targets with the Ca/P ratios of 1.0-1.67, hydroxyapatite ($Ca_{10}(PO_4)_6(OH)_2$, HAp) thin films with 4-7㎛ thickness were prepared on titanium metal plates by r.f. magnetron sputtering, followed an annealing at $200^{\circ}C$ for 24 hr under a high water vapor pressure using an autoclave. All the specimens were systematically characterized by XRD, FT-IR, SEM and EDS analyses. The post-annealed films were confirmed to be a nonstoichiometric oxyhydroxyapatite by XRD and FT-IR measurements.

• Proceedings of the Korean Powder Metallurgy Institute Conference
• /
• 2006.09b
• /
• pp.1107-1108
• /
• 2006

The coating of conductive polypyrrole (Ppy) on nonconductive ceramic substrates was performed by polymerization of pyrrole (Py) in an aqueous solution. The Ppy film was characterized by scanning electron microscopy and conductivity measurements. Electrophoretic deposition of bimodal alumina suspension prepared with a phosphate ester was performed using Ppy film as a cathode. Fabrication of alumina ceramics with irregular shapes or complicated patterns were also attempted by sintering the deposits together with the Ppy coated substrates in air.

• Journal of the Korean Society for Precision Engineering
• /
• v.12 no.6
• /
• pp.87-95
• /
• 1995

In order to predict the case depth and case width in laser transformation hardening, a finite element method was used to analyze the temperature distribution on the material. Laser hardening of the specimens of SM45C and STE11steels was experimented by using the continuous wave CO$_{2}$ laser with the various travel speeds and the defocused Gaussian beam mode. Phosphate coating was adopted on the surface of SM45C to increase the absorption of 10.6 .mu. m laser energy. Experimental data show good agreement with the theoretical predictions. The maximum possible case depth can be predicted for the given laser hardening conditions, such as laser power, and travel speed.