• Journal of the Korean Wood Science and Technology
• /
• v.27 no.2
• /
• pp.23-30
• /
• 1999

This study was carried out to develop the Korean paper(Hanji) sludge-wood fiber composite boards utilizing the relinquished sludges occurring from the making process of Korean classic paper Hanji. The bark of paper mulberry(Broussonetia kazinoki Sieb.) has been used as a raw material since past hundreds and thousands years. Korean paper(Hanji) sludge was divided into two kinds, the one was the white sludge from the first stage and the other was the black sludge occurring from the final stage of Korean paper(Hanji) making. Four levels of the mixed ratio of each white or black sludge to wood fiber(10:90, 20:80, 30:70 and 40:60), three levels of the resin adhesives(PMDI, urea and phenol resin) and three levels of the density(0.60, 0.75 and 0.90) were designed to investigate the physical properties of Korean paper(Hanji) sludge-wood fiber composite boards. From the results and discussion, it could be concluded as follows : 1. In the white sludge-wood fiber composite board, the thickness swelling was not affected by the specific gravity and sludge additive of composite boards, but among the resin adhesives PMDI resin showed the best dimensional stability. Water absorption was superior in urea resin, secondly PMDI resin and very poor in phenol resin. 2. In the black sludge-wood fiber composite board, thickness swelling was superior in PMDI resin but very poor in phenol resin. In water absorption, PMDI and urea resin showed good results, regardless of specific gravity or sludge additive, but phenol resin showed poor results. 3. From the results and discussion of physical properties it is suggested that the white sludge-wood fiber composite boards bonded with PMDI or black sludge-wood fiber composite boards bonded with urea resin were made possibly with similar or better properties. compared with general fiberboard until the addition of 20% sludge into wood fiber.

• Journal of Adhesion and Interface
• /
• v.7 no.1
• /
• pp.16-22
• /
• 2006

In this work, the effect of cure temperature and time on the thermal stability and the exothermic cure reaction peak of a waterborne resol-type phenol-formaldehyde resin, which may be used for preparing phenolic sheet molding compounds (SMC), has been investigated using a thermogravimetric analyzer and a differential scanning calorimeter. The weight loss of waterborne phenol-formaldehyde resin was mainly occurred at three temperature stages: near $200^{\circ}C,\;400^{\circ}C$, and $500^{\circ}C$. The carbon yield at $750^{\circ}C$ for the cured resin was about 62%~65%. Their thermal stability increased with increasing cure temperature and time. Upon cure, the exothermic reaction was taken placed in the range of $120^{\circ}C{\sim}190^{\circ}C$ and the maximum peak was found in between $165^{\circ}C$ and $170^{\circ}C$. The shape and the maximum of the exothermic curves depended on the given cure temperature and time. To remove $H_2O$ and volatile components, the uncured resin needed a heat-treatment at $100^{\circ}C$ for 60 min at least prior to cure or molding. Curing at $130^{\circ}C$ for 120 min made the exothermic peak of waterborne phenol-formaldehyde resin completely disappeared. And, post-curing at $180^{\circ}C$ for 60 min further improved the thermal stability of the cured resin.

• Journal of the Korean Chemical Society
• /
• v.42 no.3
• /
• pp.292-296
• /
• 1998

The elution behavior of copper(Ⅱ) and iron(Ⅱ) ions by phenol sulfonic acid(PSA) as an eluent on chelating resin, Amberlite IRC-718 have been investigated. When copper(Ⅱ) and iron(Ⅱ) solutions were adsorbed on the resin and eluted with various concentration of PSA, two peaks of each ion were appeared in the elution curve. These two peak areas were changed according to the PSA concentration. Using these phenomena, the stability constants of complex formation between the two ions and PSA were calculated. The values are 7.0 for copper(II) and $4.5{\times}10^4$ for iron(II), respectively.

• Journal of the Korean Applied Science and Technology
• /
• v.24 no.4
• /
• pp.339-346
• /
• 2007

The influence of adding urea to phenol-formaldehyde (PF) resins as a co-polymer component were investigated aiming at synthesizing useful phenol-urea-formaldehyde resins. Urea was added at 10% by total resin weight. Several methods for the addition of urea to the PF resins during synthesizing resins to see the co-polymerization occurs between urea and PF resins. The urea was added at the beginning, at three different middle stages, and at the end of PF resin synthesis. The copolymerized methylene bridges between phenol and urea molecules were not observed by $^{13}C-NMR;$ no signal around 50ppm. The curing of urea-modified PF resins, evaluated by dynamic mechanical analysis(DMA), showed some differences among the resins. DMA gel times ranged from 2.75 min to 3.25 min and the resins made with earlier urea additions showed slightly shorter gel times. The longest cure time and gelation time was observed for the resin PFU. Catalyst effects on the DMA cure time values of resins were not significant with different amounts of catalyst or different types of catalyst for all resins tested. Gel times of urea-modified PF resins shortened the most by triacetin catalyst.

• Proceedings of the Korean Society For Composite Materials Conference
• /
• 2000.11a
• /
• pp.50-53
• /
• 2000

The effect of punching density on the mechanical and thermal properties of nonwoven needle-punched carbon/phenol composite was studied. The carbonized preforms were farmed into composites with phenol resin. The interlaminar shear, tensile and flexural strengths were increased with increasing punching density. However, excessive punching density decreased interlaminar shear and tensile strengths. Erosion rate of carbon/phenol composite was decreased with increasing punching density

• Korean Journal of Microbiology
• /
• v.35 no.3
• /
• pp.237-241
• /
• 1999

Phenolic resin wastewater contained 41,000 mglI phenol, 2,800 mg/l fonualdehyde and various chlorinated phenolic compounds. Candida tropicalis PW-51 isolated [rom the natural enVlfooment was able to degrade 1,000 mg/l phenol in the presence of 100 mglI formaldehyde, but it took much time to degrade phenol with the increase of formaldehyde in phenolic resin wastewater. %en the phenolic resin wastewater was diluted to 1/40, the initial concentration of phenolic compounds (phenols) was 882 mglI and degraded to 81 mglI by C tfVpicalis PW-51 in batch culture. In a continuous biological treatment, the phenolic resin wastewater was diluted to 40 (745 mglI), 20 (1,356 mglI), or 10 (2,875 mglI) times. The removal efficiency of phenols in 1/40- and lI20-diluted phenolic resin wastewater was about 92%, but the phenols in 1!1O-diluted wastewater were not degraded. The remained phenols in wastewater were absorbed by a mixture of activated carbon and rice bran (1:1, v:v) in the process of absorption which was connected to the biological treatment. The total removal efficiency of phenols in 1!40~ and l/20-diluted phenolic resin wastewater was 99.9%.

• Journal of Korea Technical Association of The Pulp and Paper Industry
• /
• v.44 no.3
• /
• pp.41-48
• /
• 2012

Materials used for the inks in the printing industry is an important material following the paper. The composition of the ink is pigment and organic solvents. However, Ink is used in a variety of chemicals, they are classified as non-green. Therefore, rosin-modified phenolics manufactured by the reaction of phenol and formaldehyde can take the place of eco-phenol free resin and by experiment density, gloss, trapping, contrast and dot gain of printing has been studied as printability. The result of study can support that the properties of printing using eco-phenol free resin such as density, gloss, contrast and trapping is similar to existing ink. In the part of dot gain, the result is excellent. So we were thought to be able to improve some characteristics such as dispersion of black ink, that will be possible for the field applicability.

• Bulletin of the Korean Chemical Society
• /
• v.33 no.10
• /
• pp.3177-3183
• /
• 2012

The carbon nanofibers (CNFs) used in this study were synthesized with an iron catalyst and ethylene as a carbon source. A concentration of 30 wt % iron(III) acetylacetonate was dissolved in resol type phenol resin and polyurethane foam was put into the solution. The sample was calendered after being cured at $80^{\circ}C$ in air for 24 h. Stabilization and carbonization of the resol type phenol resin and reduction of the $Fe^{3+}$ were completed in a high-temperature furnace by the following steps: 1) heating to $600^{\circ}C$ at a rate of $10^{\circ}C/min$ with a mixture of $H_2/N_2$ for 4 h to reduce the $Fe^{3+}$ to Fe; 2) heating to $1000^{\circ}C$ in $N_2$ at a rate $10^{\circ}C/min$ for 30 minutes for pyrolysis; 3) synthesizing CNFs in a mixture of 20.1% ethylene and $H_2/N_2$ at $700^{\circ}C$ for 2 h using a CVD process. Finally, the structural characterization of the CNFs was performed by scanning electron microscopy and a synthesis analysis was carried out using energy dispersive spectroscopy and X-ray photoelectron spectroscopy. Specific surface area analysis of the CNFs was also performed by $N_2$-sorption.

• Carbon letters
• /
• v.7 no.3
• /
• pp.161-165
• /
• 2006

Activated carbon fiber could be prepared at 973 K by catalytic activation using potassium hydroxide. Phenol resin fiber (Kynol) was impregnated with potassium hydroxide ethanol solution, carbonized and activated at 973 K, resulting in activated carbon fibers with different porosities. The potassium hydroxide accelerated the activation of the fiber catalytically to form narrow micropore preferentially in carbon dioxide atmosphere. The narrow micropore volume of 0.3~0.4 cc/g, total pore volume of 0.3~0.8 cc/g, mean pore width of 0.5~0.7 nm was obtained in the range of 20~50% burnoff.

• Journal of Adhesion and Interface
• /
• v.12 no.4
• /
• pp.138-143
• /
• 2011

Recently epoxy resin compositions having backbone of novolac derivatives with biphenylene compounds have been used as materials of eco-freindly EMC (Epoxy Molding Compound), because the cured epoxy resin compositions show the self-extinguishing without flame retardant additives. In this study, epoxy resin compositions were prepared and cured using novolac derivateves with biphenylene. Their propeties - structures of phenol derivatives and reactivity, thermal expansion, modulus, and thermal degradation - were obtained by DSC, DMA, TMA, TGA method. When both epoxy resin and hardenr had the biphenyl novolac structure, epoxy resin compositions showed low thermal expansion, good mechanical property, and combustion retardation.