• Journal of the Korean Ceramic Society
• /
• v.24 no.4
• /
• pp.364-368
• /
• 1987

The Si5AION7 specimens containing 20% YAG composition have been sintered and then heat treated to induce the crystallization of the matrix glassy phase. Crystallization of YAG phase during the heat treatment was detected from the X-ray diffraction patterns and the consequent changes in room temperature toughness as well as in microstructures were investigated. Almost all the glassy boundary phase were found to crystallize even after 5 minutes of heat treatment and the KC at room temperature decreased accordingly. The results show that the matrix crystallization can be induced by slow cooling from the sintering temperature.

• Journal of Mechanical Science and Technology
• /
• v.16 no.10
• /
• pp.1303-1313
• /
• 2002

Effects of the reduced frequency of upstream wake on downstream unsteady boundary layer flow were simulated by using a Wavier-Stokes code. The Wavier-Stokes code is based on an unstructured finite volume method and uses a low Reynolds number turbulence model to close the momentum equations. The geometry used in this paper is the MIT flapping foil experimental set-up and the reduced frequency of the upstream wake is varied in the range of 0.91 to 10.86 to study its effect on the unsteady boundary layer flow. Numerical solutions show that they can be divided into two categories. One is so called the low frequency solution, and behaves quite similar to a Stokes layer. Its characteristics is found to be quite similar to those due to either a temporal or spatial wave. The low frequency solutions are observed clearly when the reduced frequency is smaller than 3.26. The other one is the high frequency solution. It is observed for the reduced frequency larger than 7.24. It shows a sudden shift of the phase angle of the unsteady velocity around the edge of the boundary layer. The shift of phase angle is about 180 degree, and leads to separation of the boundary layer flow from corresponding outer flow. The high frequency solution shows the characteristics of a temporal wave whose wave length is half of the upstream frequency. This characteristics of the high frequency solution is found to be caused by the strong interaction between unsteady vortices. This strong interaction also leads to destroy of the upstream wake strips inside the viscous sublayer as well as the buffer layer.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.42 no.2
• /
• pp.453-459
• /
• 2017

Users tend to check in and post their statuses in location-based social networks (LBSNs) to describe that their interests are related to a point-of-interest (POI). While previous studies on discovering area-of-interests (AOIs) were conducted mostly on the basis of density-based clustering methods with the collection of geo-tagged photos from LBSNs, we focus on estimating a POI boundary, which corresponds to only one cluster containing its POI center. Using geo-tagged tweets recorded from Twitter users, this paper introduces a density-based low-complexity two-phase method to estimate a POI boundary by finding a suitable radius reachable from the POI center. We estimate a boundary of the POI as the convex hull of selected geo-tags through our two-phase density-based estimation, where each phase proceeds with different sizes of radius increment. It is shown that our method outperforms the conventional density-based clustering method in terms of computational complexity.

• Korean Journal of Optics and Photonics
• /
• v.18 no.2
• /
• pp.122-129
• /
• 2007

Generally, many kinds of phase unwrapping algorithm are used to obtain three-dimensional features in digital holography. The Goldstein algorithm is ra epresentative method. which requires small memory capacity and short execution time fer an unwrapping process. However, the Goldstein algorithm has some problems when the dipole residue is located at the boundary. When the opposite residues are located at the boundary and the distance between the opposite residues is longer than the boundary, an incorrect branch cut occurs and results in incorrect calculation. We have modified the Goldstein algorithm to solve the incorrect calculation problem using boundary information. We found that the modified Goldstein algorithm could resolve the Goldstein algorithm's problem.

• Journal of the Korea Institute of Building Construction
• /
• v.13 no.4
• /
• pp.321-332
• /
• 2013

Costs and expenses are intertwined and incurred throughout an entire construction project, even from the pre-construction phase, and each phase has a different impact on the life cycle cost (LCC). However, the cost breakdown structure (CBS) is different in each phase of a building construction project, which makes it hard to reasonably calculate construction cost. For this reason, the boundary conditions were analyzed in this study based on the life cycle cost break structure (LCCBS). In addition, breakdown factors were analyzed based on the boundary conditions to derive a linkage method. The validity of the linkage method was verified through application to actual construction projects. Through the analysis, it was found that the problem of items being left out was reduced by more than 97.2 percent, and the work was done an average of 6 hours faster compared to the conventional method. It is expected that by applying the new LCC system, LCC will be both reduced and calculated in a more efficient manner.

• Journal of Welding and Joining
• /
• v.25 no.3
• /
• pp.64-71
• /
• 2007

The dissolution phenomenon of the solid phase powder and base metal by liquid phase insert metal during Transient Liquid Phase bonding using the mixed powder composed of the modified GTD111(base metal) powder and the GNi3 (Ni-l4Cr-9.5Co-3.5Al-2.5B) powder was investigated. In case of the mixed powder contains modified GTD111 powder 50wt%, all of the powder was melted by liquid phase at 1423K. At the temperature between solidus and liquidus of GNi3, liquid phase penetrated into the boundary of the modified GTD111 powder and solid particle separated from powder was melted easily because area of reaction was increased. With increasing mixing ratio of the modified GTD111, it needed the higher temperature to melt all of the modified GTD111 powder. During Transient Liquid Phase bonding using the mixed powder composed of the modified GTD111 50wt% and GNi3 50wt% as insert metal, width of the bonded interlayer was increased with increasing bonding temperature by reaction of the base metal and liquid phase in insert metal. Dissolution of the base metal and modified powder by liquid phase progressed all together and after all of the powder was melted nearly, the dissolution of the base metal occurred quickly.

• Honam Mathematical Journal
• /
• v.36 no.1
• /
• pp.11-27
• /
• 2014

In this paper, we propose closures for multi-phase flow models, which satisfy boundary conditions and conservation constraints. The models governing the evolution of the fluid mixing are derived by applying an ensemble averaging procedure to the microphysical equations characterized by distinct phases. We consider compressible multi species multi-phase flow with surface tension and transport.

• The Korean Journal of Ceramics
• /
• v.7 no.2
• /
• pp.70-73
• /
• 2001

Phase transformation of TiSi$_2$ confined in sub-micron area of which the size is around or smaller than the grain size of C49 TiSi$_2$ phase is studied. It has been known that the C49 to C54 phase change is massive transformation that occurs abruptly starting from C54 nuclei located at triple point grain boundaries of C49 phase. When the C49 phase is confined in sub-micron area, however, the massive phase transformation is observed to be hindered due to the lack of the triple point grain boundaries of C49 phase. Heat treatment at higher temperatures starts to decompose the C49 phase, and the resulting decomposed Ti atoms diffuse to, and react with, the underneath Si material to form C54 phase that exhibits spherical interface with silicon. The newly formed C54 grains can also trigger the massive phase transformation to convert the remaining undecomposed C49 grains to C54 grains by serving as nuclei like conventional C54 nuclei located at triple point grain boundaries.

• Interaction and multiscale mechanics
• /
• v.1 no.2
• /
• pp.191-209
• /
• 2008

In this paper, we model grain boundary evolution based on a multiple level set method. Grain boundary migration under a curvature-induced driving force is considered and the level set method is employed to deal with the resulting topological changes of grain structures. The complexity of using a level set method for modeling grain structure evolution is due to its N-phase nature and the associated geometry compatibility constraint. We employ a multiple level set method with a predictor-multicorrectors approach to reduce the gaps in the triple junctions down to the grid resolution level. A ghost cell approach for imposing periodic boundary conditions is introduced without solving a constrained problem with a Lagrange multiplier method or a penalty method. Numerical results for both uniform and random grain structures evolution are presented and the results are compared with the solutions based on a front tracking approach (Chen and Kotta et al. 2004b).

• Journal of IKEEE
• /
• v.18 no.4
• /
• pp.463-470
• /
• 2014

In stratified flows of two immiscible liquids, due to the vibration in a pipe, the shape of the interface is not always periodic and it causes the different end points of the interfacial boundary. In this case the performance is not good. To solve this, in this paper, the hybrid-type Fourier series is proposed, which consists of both the polynomial and the trigonometric terms. Under the stationary interfacial boundary during acquiring a full set of voltage data, the performance of the proposed method is evaluated through the numerical experiments. The results show that the proposed method performs better than the conventional Fourier series in estimating the interfacial boundary.