• Proceedings of the KIPE Conference
• /
• 2002.07a
• /
• pp.415-418
• /
• 2002

In the paper, a four-phase 16/12 structure Switched Reluctance motor drive is presented. The construction of the stator and the rotor in the motor, the scheme of the rotor position detector and the main circuit of the power converter are described. The comparison of the four-phase 16/12 motor and the four-phase 816 motor and the comparison of the four-phase 16/12 motor and the three-phase 12/8 motor are made. In the controller, the PWM control variable-speed control, the commutation control, the four quadrants control, the overvoltage protection, the overcurrent protection and the under voltage protection could be achieved. Tested results of the developed prototype are made.

• The Transactions of the Korean Institute of Electrical Engineers B
• /
• v.48 no.9
• /
• pp.461-466
• /
• 1999

The switched reluctance motor (SRM) would have torque ripple if not operated with an MMF waveform specified for switching angle and phase voltage. This paper describes the robustic control scheme that permits the phase torque to be flat by PLL(Phase Locked Loop) controller. In this control scheme, the locked phase signal of PLL controls the switching dwell angle and it's loop filter signal controls the switching voltage adaptively. Experimental results show that stable dynamic performance is obtained for torque and speed together with low torque ripple on the operation of variable loads.

• Proceedings of the KIEE Conference
• /
• 1994.07a
• /
• pp.389-391
• /
• 1994

This paper proposes an approach to control the current amplitude and phase simultaneously. To do this, variable structure control and adaptive parameter estimation arc applied to the current control of a single-phase PWM inverter with unknown R-L series load. The load parameters, R and L, are estimated by using the recursive least square method and these parameters are used to adjust the feedback gains of control input. The inverter system is modelled in a 2nd-order system by treating load current variation caused by inductive component as a disturbance. Simulation and experiment based on the 2nd -order model are done and the results show good dynamic response and low THD.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.58 no.7
• /
• pp.1313-1320
• /
• 2009

This paper analyzes the steady-state operating characteristics of doubly-fed induction generator(DFIG) and fixed-speed induction generator(FSIG) in wind turbine system. It also presents a modeling and simulation of a grid-connected wind turbine generation system for dynamics analysis on MATLAB/Simulink, and compares the responses between DFIG and FSIG wind turbine systems with respect to wind speed variation, 3-phase fault and 1-phase ground fault of the network. Simulation results show the variations of generator's active/reactive output, rotor speed, terminal voltage, fault current, etc. Case studies demonstrate that DFIG illustrates better performance compared to FSIG.

• Proceedings of the KIEE Conference
• /
• 2003.10a
• /
• pp.120-122
• /
• 2003

We have been investigated phase-change with temperature and electric field in chalcogenide $Ge_2Sb_2Te_5$ thin film. $T_c$(crystallization temperature) is confirmed by measuring the resistance and conductivity with the varying temperature on the hotplate. We have measured I-V characteristics with $Ge_2Sb_2Te_5$ chalcogenide thin film. It is compared with I-V characteristics after impress the variable pulse. The pulse has variable height and duration that used voltage and current source.

• Proceedings of the KIPE Conference
• /
• 2004.07a
• /
• pp.195-195
• /
• 2004

Conventional dryer systems use one induction motor to drive drum and fan. However, nowadays, dryer systems are necessary to use extra fan motor for reducing a drying-time. This fan motor should be variable-speed controlled motor to control drying-time according to the volume of clothes. This paper proposes 3-phase SRM(Switched Reluctance Motor) having 12/8 structure for variable-speed fan motor of dryer system.

• Proceedings of the KIEE Conference
• /
• 2001.07b
• /
• pp.1101-1104
• /
• 2001

This paper describes a newly developed power conditioner with variable current loop gain. The power conditioner consists of a do-link capacitor and three phase inverter with coupled inductor. This system is very well operated to compensate current harmonics and asymmetries caused by nonlinear load and unbalance loads. The power conditioner shapes the source current sinusoidal in phase with source voltage. A 100kVA power conditioner was built and the controller is realized with DSP Experimental results for many load conditions are presented to verify the performance of the controller.

• Proceedings of the KIPE Conference
• /
• 1999.07a
• /
• pp.522-525
• /
• 1999

This paper describes a simple but effective method for energy saving of ac motors having a widely variable load. The proposed method is based on an optimal efficiency control which is operated by voltage-current pattern such as to maintain the maximum efficiency on the efficiency-output characteristics of the motor, in voltage control with triac. In this paper, authors present the experimental results of the SPIM under controlling of current of main and auxiliary winding by using a one chip microcontroller. Experiments are focused on a capacitor stating single phase induction motor the optimal energy saving are proved by the proposed method.

• The Transactions of the Korean Institute of Electrical Engineers A
• /
• v.48 no.6
• /
• pp.719-727
• /
• 1999

A robust position control method of the BLDC motor using a new sliding mode control strategy is presented. The main property of variable structure system(VSS) is that the system response is robust and insensitive to parameter variations and external disturbances in the sliding mode. When using the conventional VSS, generally the reaching phase problem occurs, which cause the system response to be sensitive to parameter variations and external disturbances. Furthermore, the speed of response is relatively slow because the swithching surface is a linear function. In order to overcome these problems, VSS with nonlinear sliding surface eliminating reaching phase is proposed. The validity of the proposed scheme is shown by results of simulations of simulations and experiments for the BLDC motor with variable load.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.59 no.5
• /
• pp.950-960
• /
• 2010

In this paper, a multi-input multi-output(MIMO) integral variable structure system with an integral-augmented sliding surface is designed for the improved robust control of uncertain multivariable system under the matched persistent disturbance. To effectively remove the reaching phase problems, the integral augmented sliding surface is proposed. Then for its design, the eigenstructure assignment technique is introduced to. To guarantee the designed performance against the persistent disturbance, the stabilizing control for multi-input system is also designed to generate the sliding mode on the integral sliding surface. The stability of the global system together with the existence condition of the sliding mode are investigated and proved for the case of multi input system in the presence of uncertainty and disturbance. The reaching phase is completely removed in proposed MIMO VSS by satisfying the two requirements. An example and computer simulations will be present for showing the usefulness of algorithm.