• Transactions of the Korean Society of Mechanical Engineers
• /
• v.18 no.2
• /
• pp.479-491
• /
• 1994

Discrete vortex method was applied for simulating an active control of turbulent leading- edge separation bubble. The leading-edge separation zone was perturbed by a time-dependent sinusoidal perturbation of different frequencies and levels. In order to describe the local sinusoidal perturbation at the separation point, a source pulsation vortex technique was proposed. The present two-dimensional vortex simulations were qualitatively compared with the experimental results for a blunt circular cylinder, where perturbation was introduced along the square-cut leading edge of the cylinder $(Kiya et al.^{(6,7)}).$ It was found that the reattachment length attained a minimum point at low levels of perturbation and two minima at a moderate higher perturbation frequency. The effects of local perturbation on the evolution of leading-edge separation bubble were scrutinized by comparing the perturbed flow with the natural flow. These comparisons were made for the distributions of mean velocity and its velocity fluctuations, intermittency and wall velocity. The motions of instantaneous reattachment in the space-time domain were demonstrated, which were also compared with the experimental findings. In order to investigate the reduction mehanism of reattachment length in the separation bubble, various cross-correlations for velocity and pressure and the relevant convection velocities were evaluated. It was observed that the convection velocity was closely associated with its corresponding pulsationg frequency.

• Journal of KSNVE
• /
• v.11 no.2
• /
• pp.323-328
• /
• 2001

The paper describes a theoretical study on the flexural vibration of an elastic rectangular plate with periodically nonuniform material properties. The approximate solution of the natural frequency and mode shape has been obtained using the perturbation technique for sinusoidal modulation of the flexural rigidity and mass density. It has been shown that distributed modes exist in the plate which Is a two-dimensional model of the flat panel speaker.

• Journal of the Korean Magnetic Resonance Society
• /
• v.22 no.4
• /
• pp.125-131
• /
• 2018

Chemical shift perturbation (CSP) is a simple NMR technique for studying binding of a protein to various ligands. CSP is the only technique that can directly provide both a value for the dissociation constant and a binding site from the same set of measurements. To accurately analyze the CSP data, the exact binding mode such as multiple binding, should be carefully considered. In this review, we analyzed systematically the CSP data with multiple modes. This analysis might provide insight into the mechanism on how proteins selectively recognize their target ligands to achieve the biological function.

• Structural Engineering and Mechanics
• /
• v.73 no.1
• /
• pp.75-82
• /
• 2020

In this study, the problem of torsion of bars with open cross section surrounded by corrugated boundaries is analyzed. An approximate analytical solution is given using perturbation technique. First, the stress analysis for circular open cross-section for arbitrary opening angle is formulated and the problem is analytically solved. Second, the open cross-section with corrugated cross section is analyzed using perturbation method. First order contributions to the stresses and the torques have been added. The results have been exemplified and compared by considering special examples.

• Proceedings of the Korean Society of Medical Physics Conference
• /
• 2002.09a
• /
• pp.263-266
• /
• 2002

We have developed a practical method for estimating high-energy x-ray spectra using measured attenuation curves. This method is based on the iterative perturbation technique proposed by Waggener et al. The principle is to minimize the difference between the measured and calculated transmission curves. The experimental study was made using 4 MV, 10 MV, and 15 MV x-ray beams. It has been found that the spectrum varies strongly with the off-axis distance.

• International Journal of Naval Architecture and Ocean Engineering
• /
• v.7 no.5
• /
• pp.920-938
• /
• 2015

In the present study, a numerical prediction method on the hydrodynamic interaction force and moment between two ships in shallow and restricted waterway is presented. Especially, the present study proposes a methodology to overcome the limitation of the two dimensional perturbation method which is related to the moored-passing ship interaction. The validation study was performed and compared with the experiment, firstly. Afterward, in order to propose a methodology in terms with the moored-passing ship interaction, further studies were performed for the moored-passing ship case with a Reynolds Averaged Navier-Stokes (RANS) calculation which is using OpenFOAM with Arbitrary Coupled Mesh Interface (ACMI) technique and compared with the experiment result. Finally, the present study proposes a guide to apply the two dimensional perturbation method to the moored-passing ship interaction. In addition, it presents a possibility that the RANS calculation with ACMI can applied to the ship-ship interaction without using a overset moving grid technique.

• Phonetics and Speech Sciences
• /
• v.2 no.3
• /
• pp.165-170
• /
• 2010

In this study, the most stable portion was identified using 5% moving window during /a/ sustained phonation in normal and pathologic voice signals and the perturbation values were compared between normal and pathologic voices at the mid-point and at the most stable portion using moving window, respectively. The results revealed that some severe pathologic voice signals can be eligible for perturbation analysis by identifying the most stable portion with Err less than 10. In addition, the perturbation acoustic parameters did not differentiate the pathologic voice signals from the normal voice signals when the mid-point was selected to measure the perturbation analysis(p>0.05). However, significantly higher %shimmer and lower SNR values were observed in pathologic voices (p<0.05) when the most stable portion was selected by moving window. In conclusion, moving window could identify the most stable portion objectively which can allow toget the minimum perturbation values (%jitter, %shimmer) and maximum SNR values. Thus, moving window technique can be applicable for more reliable and accurate perturbation acoustic analysis.

• Steel and Composite Structures
• /
• v.8 no.2
• /
• pp.129-144
• /
• 2008

This paper demonstrates an application of the perturbation based stochastic finite element method (SFEM) for predicting the performance of structural systems made of composite sections with random material properties. The composite member consists of materials in contact each of which can surround a finite number of inclusions. The perturbation based stochastic finite element analysis can provide probabilistic behavior of a structure, only the first two moments of random variables need to be known, and should therefore be suitable as an alternative to Monte Carlo simulation (MCS) for realizing structural analysis. A summary of stiffness matrix formulation of composite systems and perturbation based stochastic finite element dynamic analysis formulation of structural systems made of composite sections is given. Two numerical examples are presented to illustrate the method. During stochastic analysis, displacements and sectional forces of composite systems are obtained from perturbation and Monte Carlo methods by changing elastic modulus as random variable. The results imply that perturbation based SFEM method gives close results to MCS method and it can be used instead of MCS method, especially, if computational cost is taken into consideration.

• Smart Structures and Systems
• /
• v.10 no.4_5
• /
• pp.427-442
• /
• 2012

An effective approach for updating finite element model is presented which can provide reliable estimates for structural updating parameters from identified operational modal data. On the basis of the dynamic perturbation method, an exact relationship between the perturbation of structural parameters such as stiffness change and the modal properties of the tested structure is developed. An iterative solution procedure is then provided to solve for the structural updating parameters that characterise the modifications of structural parameters at element level, giving optimised solutions in the least squares sense without requiring an optimisation method. A regularization algorithm based on the Tikhonov solution incorporating the generalised cross-validation method is employed to reduce the influence of measurement errors in vibration modal data and then to produce stable and reasonable solutions for the structural updating parameters. The Canton Tower benchmark problem established by the Hong Kong Polytechnic University is employed to demonstrate the effectiveness and applicability of the proposed model updating technique. The results from the benchmark problem studies show that the proposed technique can successfully adjust the reduced finite element model of the structure using only limited number of frequencies identified from the recorded ambient vibration measurements.

• International Journal of Computer Science & Network Security
• /
• v.23 no.6
• /
• pp.99-106
• /
• 2023

Now a days, large volumes of data is accumulating in every field due to increase in capacity of storage devices. These large volumes of data can be applied with data mining for finding useful patterns which can be used for business growth, improving services, improving health conditions etc. Data from different sources can be combined before applying data mining. The data thus gathered can be misused for identity theft, fake credit/debit card transactions, etc. To overcome this, data mining techniques which provide privacy are required. There are several privacy preserving data mining techniques available in literature like randomization, perturbation, anonymization etc. This paper proposes an Enhanced Hybrid Privacy Preserving Data Mining(EHPPDM) technique. The proposed technique provides more privacy of data than existing techniques while providing better classification accuracy. The experimental results show that classification accuracies have increased using EHPPDM technique.