• 한국철도학회논문집
• /
• 제15권2호
• /
• pp.135-140
• /
• 2012

집중권 방식의 견인용 영구자석 매입형 동기전동기(IPMSM)는 출력밀도의 관점에서 우수하나 심각한 영구자석 와전류 손실을 가지고 있다. 본 논문에서는 영구자석 매입형 동기전동기의 자기적 특성을 분석하여 V-타입 회전자 영구자석의 각도와 폭을 변경함으로써 철손을 최소화하는 최적설계를 수행하였다. 자성체의 비선형성을 고려하기 위하여 자기등가회로법 대신 유한요소법을 이용하였으며, 각 파라메타가 영구자석에 발생하는 철손에의 영향 및 파라메타간의 교호작용을 파악하기 위하여 시뮬레이션 기반의 실험계획법을 사용하였다. 이를 통하여 모터의 성능을 유지하면서 철손을 상당히 줄인 집중권 방식의 영구자석 매입형 동기전동기의 최적설계를 반응표면법을 이용하여 도출하였으며, 유한요소법을 이용하여 이를 검증하였다.

• 한국철도학회:학술대회논문집
• /
• 한국철도학회 2011년도 정기총회 및 추계학술대회 논문집
• /
• pp.1832-1837
• /
• 2011

This paper presents the optimal permanent magnet shape on the rotor of an interior permanent magnet motor to reduce the core losses and improve the performance. As permanent magnet has conductivity inherently, it causes huge amount of eddy current losses by the slot harmonics with concentrated winding. This loss is roughly 100 times larger than that of distributed winding in high speed operation and it cannot be ignored, especially on traction motors. Each eddy current loss on permanent magnet has been investigated in detail by using FEM(Finite Element Method) instead of EMCNM(Equivalent Magnetic Circuit Network Method) in order to consider saturation and non-linear magnetic property. Simulation-based DOE(Design Of Experiment) is also applied to avoid large number of analyses according to each design parameter and consider expected interactions among parameters. Consequently, the optimal design to reduce the core loss on the permanent magnet while maintaining or improving motor performance is proposed by an optimization algorithm using regression equation derived and lastly, the core loss reduction on the proposed shape of the permanent magnet is verified by FEM.

• Journal of Magnetics
• /
• 제16권1호
• /
• pp.64-70
• /
• 2011

Surface-mounted permanent magnet (PM) machines were examined experimentally and theoretically, through power loss measurements and calculations. Windage, friction and copper losses were calculated using simple analytical equations and finite element (FE) analyses. Stator core losses were calculated by determining core loss coefficients through curve-fitting and magnetic behavior analysis through non-linear FE calculations. Rotor eddy current losses were calculated using FE analyses that considered the time harmonics of phase current according to load. Core, windage and friction open-circuit losses and copper loss were determined experimentally to test the validity of the analyses.

• Journal of Electrical Engineering and Technology
• /
• 제13권5호
• /
• pp.1956-1964
• /
• 2018

Since the stator winding of High-Speed Permanent Magnet Generator (HSPMG) has few winding turns and low inductance value, it is more prone to be influenced by harmonic current. Moreover, the operation efficiency and the torque stability of HSPMG will be greatly influenced by harmonic current. Taking a 117 kW, 60 000 rpm HSPMG as an example, in order to analyze the effects of harmonic current on HSPMG in this paper, the 2-D finite element electromagnetic field model of the generator was established and the correctness of the model was verified by testing the generator prototype. Based on the model, the losses and torque of the generator under different frequency harmonic current were studied. The change rules of the losses and torque were found out. Based on the analysis of the influence of the harmonic phase angle on torque ripple, it is found that the torque ripple could be weakened through changing the harmonic phase angle. Through the analysis of eddy current density in rotor, the change mechanism of the rotor eddy current loss was revealed. These conclusions can contribute to reduce harmonic loss, prevent demagnetization fault and optimize torque ripple of HSPMG used in distributed power supply system.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2011년도 제42회 하계학술대회
• /
• pp.1073-1074
• /
• 2011

The loss is most important problems for the practical applications of permanent magnet synchronous motor(PMSM). In this paper, rotor sleeve and stator shape design of high speed permanent magnet motor for loss reduction. First, this paper found optimum sleeve thickness for calculation eddy current loss on the basis of analytical method, because eddy current is influenced by conductivity of material and area. Then, stator shape design is changed as maintain same slot area for reducing stator core loss. Finally, this paper compared analytical result with optimum sleeve thickness obtained from finite element(FE) method, and stator core loss is calculated from FE method.

• Journal of Electrical Engineering and Technology
• /
• 제12권4호
• /
• pp.1566-1574
• /
• 2017

When the inter-turn short circuit (ITSC) fault occurs, the distortion of the magnetic field is serious. The motor loss variations of each part are obvious, and the motor temperature field is also affected. In order to obtain the influence of the ITSC fault on the motor temperature distribution, firstly, the normal and the fault finite element models of the permanent magnet synchronous motor (PMSM) were established. The magnetic density distribution and the eddy current density distribution were analyzed, and the mechanism of loss change was revealed. The effects of different forms and degrees of the fault on the loss were obtained. Based on the loss analysis, the motor temperature field calculation model was established, and the motor temperature change considering the loop current was analyzed. The influence of the fault on the motor temperature distribution was revealed. The sensitivity factors that limit the motor continuous operation were obtained. Finally, the correctness of the simulation was verified by experiments. The conclusions obtained are of great significance for the fault and high temperature demagnetization of the permanent magnet analysis.

• Journal of Magnetics
• /
• 제19권3호
• /
• pp.309-313
• /
• 2014

This paper presents an eddy current loss analysis of a Mechanical Fixation (MF) made of 6061 aluminum alloy, which is used for an NS type double-rotor single-stator axial flux permanent magnet machine. The prototype MF made of aluminum alloy shows good mechanical performance, but poor electro-magnetic performance, since the machine's efficiency can decrease because of eddy current loss in the MF. In order to prevent efficiency decrease, a modification of the MF structure is also introduced. Three-dimensional finite element analysis (FEA) is used for magnetic field analysis, and eddy current losses are computed. The analysis results are compared to, and verified by the test results.

• KIEE International Transaction on Electrical Machinery and Energy Conversion Systems
• /
• 제5B권3호
• /
• pp.215-223
• /
• 2005

An electrical machine for a high-speed flywheel for energy storage in large hybrid electric vehicles is described. Design choices for the machine are motivated: it is a radial-flux external-rotor permanent-magnet synchronous machine without slots in the stator iron and with a shielding cylinder. An analytical model of the machine is briefly introduced whereafter optimization of the machine is discussed. Three optimization criteria were chosen: (1) torque; (2) total stator losses and (3) induced eddy current loss on the rotor. The influence of the following optimization variables on these criteria is investigated: (1) permanent-magnet array; (2) winding distribution and (3) machine geometry. The paper shows that an analytical model of the machine is very useful in optimization.

• KIEE International Transaction on Electrical Machinery and Energy Conversion Systems
• /
• 제5B권3호
• /
• pp.238-242
• /
• 2005

In this paper, a surface permanent magnet motor made of the Soft Magnetic Composites (SMC) is analysed using the 3-D finite element method. By comparing with the motor made of the silicon steel sheets, the usefulness of the SMC for the eddy current loss is clarified quantitatively.

• 한국태양에너지학회 논문집
• /
• 제34권2호
• /
• pp.8-15
• /
• 2014

The objective of this paper is to suggest a design topology of permanent magnet synchronous generator with 2,000kW capacities for wind turbine. The suggested topology is to provide 3 split magnet PMSG instead of single magnet, and performed an analysis of eddy current loss and iron loss for suggested type using ansoft maxwell commercial program. The simulation results of suggested magnet type show there duction of eddy current loss as 13.87kW with loadless conditions and23.48kW with rated conditions, but iron loss for rotor yoke show the in creasing trend as2.2kW with loadless conditions and 0.2kW with rated conditions. The suggested 3 split maget type is to identified as more useful for 2,000kW PMSG.