• 한국지반공학회:학술대회논문집
• /
• 한국지반공학회 2000년도 봄 학술발표회 논문집
• /
• pp.159-166
• /
• 2000

Non-destructive out-hole tests, impact-echo and impact-response are widely applied to evaluate integrity of drilled shafts. In these tests, vibratory motions of drilled shafts are interpreted, which induced by impacts on the shaft head. In applying the tests to evaluating integrity of shaft, it has been attended whether the tests have resolutions enough to distinguish existence of slime at between the shaft end and a bearing soil deposit. To distinguish existence of slime by tests, modes of shaft vibrations need to be reasonably interpreted, which generally vary according to a shaft boundary condition such as, a free-free or a free-fixed condition. The boundary condition of a shaft is, however, found to be significantly affected by stiffness of soil deposits around shaft as well as penetration depths of shaft into a bearing soil deposit. Thus, these effects on the boundary condition of a shaft should be considered reasonably in interpreting test results to decide the existence of slime. To investigate the effects, in this study, vibratory motions of shafts constructed in various soil conditions and end penetration depths are examined analytically. Based on the studies, variations of boundary condition are characterized in terms of soil stiffness contrast between a shaft perimeter and a shaft end, and also the ratio of a penetration depth to a shaft length. The results can be applied to verify the applicability of tests to identify the slime.

• 한국분무공학회지
• /
• 제13권2호
• /
• pp.79-84
• /
• 2008

The correlations for cross-flow have not been well established, because of the complexity of breakup and atomization mechanism. A study was performed to investigate the characteristics of spray behaviour of liquid jet in the bag breakup regime injected into low-speed cross-flow with the pressure single-hole nozzle. The shadow-graphy method was used for the cross-flow jet visualization. The experimental variables of liquid jet were nozzle diameter $(0.3mm{\sim}1.0mm)$, injection pressure $(50kPa{\sim}150kPa)$, and the velocity of cross-flow $(27m/s{\sim}42m/s)$. The highest penetration trajectories of liquid jet are governed by the momentum ratio $({\rho}_{\iota}U_{\iota}^2/{\rho}_aU_{cross}^2)$ rather than the Weber number and the new empirical equations of the highest penetration trajectory and breakup point at low-speed corss-flow are established.

• 한국추진공학회지
• /
• 제15권5호
• /
• pp.19-26
• /
• 2011

초음속 연소에서 연료를 분사하는 분사구의 형태에 따른 연소 성능의 변화를 파악하기 위하여 실험과 준일차원 해석(Quasi-One Dimensional Analysis)을 수행하였으며, 결과 값을 본 팀에서 2008년에 수행한 데이터와 비교해 보았다. 시험은 일본 JAXA에서 보유하고 있는 불어내기식 풍동을 사용하였으며, 온도조건을 맞추기 위하여 Vitiated Heater가 사용되었다. 시험을 위하여 2008년 수행하였던 시험모델에서 사용한 연료 분사구의 크기를 줄이고 개수를 증가시켰다. 연료 분사구의 크기 및 개수는 동일한 연료 압력에서 연료의 분사량과 침투깊이가 동일하도록 결정되었다. 실험결과 공동이 없을 시에는 연료 분사구의 크기를 줄이고 개수를 늘렸을 때 연소성능이 큰 폭으로 증가하였지만, 일자형 공동에서 는 그 영향이 미미하였다. 지그재그형 공동에서는 연료 분사구의 크기를 줄이고 개수를 늘렸을 때 오히려 연소성능의 저하가 관찰되었다.

• 한국분무공학회지
• /
• 제4권1호
• /
• pp.45-54
• /
• 1999

The spray characteristics of a direct injection multi-hole diesel nozzle having the 2-spring nozzle holder were investigated by using the image processing system and a PDPA(phase Bowler particle analyzer) system. The spray tip penetration, the spray angle, and the droplet diameter and velocity with the variation of the pump speed, injection quantity were measured. From, the experiments, we know that there are small droplets which are not to be detected with spray image around the leading edge of the spray. In order to represent the mean characteristics of the intermittent spray very well, it is very important to set the time windows accurately. From the measurements along the axis of the spray, close to the nozzle, the initially injected droplets are overtaken by droplets that follow them. And also there are the maximum axial mean velocity and SMD at the following part of the leading edge of the spray.

• 한국분무공학회지
• /
• 제9권1호
• /
• pp.8-14
• /
• 2004

future exhaust emission limits for diesel-driven passenger cars will force the automotive company to significantly develop of the new technologies of diesel engine respectively of the drive assemblies. As we know, the contributions of soot and nitrogen oxide is the main problems in diesel engine. Recently, as a result, the pilot injection of common-rail fuel injection system recognizes an alternative function to solve an environmental problem. This study describes the effect of the nozzle structure and driven characteristic of injector on pilot injection fur a passenger car common-rail system. The pilot spray structure such as spray tip penetration, spray speed and spray angle were obtained by high speed images, which is measured by the Mie scattering method with optical system fur high-speed temporal photography. Also the CFD analysis was carried out for fuel behavior under high pressure in between needle and nozzle of injector for common-rail system to know the condition of initial injection at experiment test. It was found that solenoid-driven injector with 5-hole was faster than 6-hole injector in spray speed at same conditions and piezo-driven injector showed faster response than solenoid injector.

• 한국추진공학회:학술대회논문집
• /
• 한국추진공학회 2010년도 제35회 추계학술대회논문집
• /
• pp.423-431
• /
• 2010

초음속 연소에서 연료를 분사하는 분사구의 형상에 따른 연소 성능의 변화를 파악하기 위하여 실험과 준일차 해석(Quasi-One Dimensional Analysis)을 수행하였으며, 결과 값을 본 팀에서 동일 설비 및 조건으로 2008년에 시험을 수행한 데이터와 비교해 보았다. 연료 분사구 형상은 2008년 수행하였던 시험모델과 비교하여 연료 분사구의 크기를 줄이고 개수를 증가시켰으며, 연료 분사구의 크기 및 개수는 동일한 연료 압력에서 연료의 분사량과 침투깊이가 동일하도록 결정되었다. 실험결과 공동이 없을 시에는 연료 분사구의 크기를 줄이고 개수를 늘렸을 때 연소성능이 큰 폭으로 증가하였지만, 일자형 공동에서는 그 영향이 미미하였다. 하지만 지그재그형 공동에서는 연료 분사구의 크기를 줄이고 개수를 늘렸을 때 오히려 연소성능이 저하되었다.

• 한국지반공학회:학술대회논문집
• /
• 한국지반공학회 2002년도 가을 학술발표회 논문집
• /
• pp.404-410
• /
• 2002

Dynamic compaction is an efficient ground improvement technique for loose soils and waste landfill. The improvement is obtained by controlled high energy tamping and its effects vary with the soil properties and energy input. This study demonstrated the application of dynamic compaction method for the improvement of waste landfill in construction site. Various tests and measurements such as standard penetration test, bore hole loading test, crater settlement, ground settlement, pore water pressure were peformed during dynamic compaction field test. From the field test results, the efficiency of dynamic compaction method for the improvement of waste landfill was proved.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2003년도 춘계학술대회 논문집
• /
• pp.764-767
• /
• 2003

The characteristics of diesel spray have much effect on the engine performances such as power. fuel consumption rate and emissions. Therefore, the measurement of fuel spray characteristics is very important for the improvement of heat engine. The factors which control diesel spray characteristics are injection pressure, ambient temperature and density etc. Spray behaviors are visualized by using the high speed video camera and spray angle, spray penetration are measured. Experimental equations of spray penetration and spray angle were derived by using the experimental results. 1) Ambient temperature and density influence on the characteristics of diesel spray. 2) Experimental equation of spray penetration is expressed as follows 0＜t＜ $t_{b}$ ; $S_1$=11.628$\Delta$ $P^{0.485}$ $\rho$$_{a}$ $^{-0.478}$ $t^{1.337}$, $t_{b}$ ＜t; $S_2$=7.457$\Delta$ $P^{0.523}$ $\rho$$_{a}$ $^{-0.382}$ $t^{0.548}$ 3) Experimental equation of spray Angie is expressed as follows $T_{a}$ =293K; Tan($\theta$/2)=059($\rho$$_{a}$ / $\rho$$_{f}$ )$^{0.437}$, $T_{a}$ =473K; Tan($\theta$/2)=0588($\rho$$_{a}$ / $\rho$$_{f}$ )$^{0.404}$_{f}$ )$^{0.404}$

• Journal of Welding and Joining
• /
• 제20권4호
• /
• pp.525-534
• /
• 2002

During laser spot welding of the braun tube electron gun, phenomena such as serious spattering and oxidative reaction, etc. were occurred. The spatter occurred from weld pool affects the braun tube, namely it blocks up a very small hole on the shadow mask and causes short circuit between two roles of the electron gun. We guessed that high power density and oxidative reaction are main sources of these problems. So, we studied to prevent and to reduce spatter occurring in spot welding of the braun tube electron gun using pulsed Nd:YAG laser. The characteristics of laser output power was estimated, and the loss of laser energy by optical parameter and spatter was measured by powermeter. The effects of welding parameters, laser defocused distance and incident angle, were investigated on the shape and penetration depth of the laser welded bead in flare and flange joints. From these results, the laser peak power was a major factor to control penetration depth and to occur spatter. It was found that the losses of laser energy by optic parameter and sticked spatter affect seriously laser weldability of thin sheets. The deepest penetration depth is gotten on focal position, and a "bead transition" occurred with a slight displacement of focal position relative to the workpiece surface and the absorption rate of the laser energy is affected by the shape factor of the workpiece. When we changed the incident angle of laser beam, the penetration depth was decreased a little with increasing of the incident angle, and the bead width was increased. The spattering was prevented by considering laser beam energy and incident angle.ent angle.

• 한국자동차공학회논문집
• /
• 제10권5호
• /
• pp.73-80
• /
• 2002

Dimethyl ether (DM) is one of the most attractive alternative fuel far compression ignition engine. Its main advantage in diesel engine application is high efficiency of diesel cycle with soot free combustion though conventional fuel injection system has to be modified due to the intrinsic properties of DME. Experimental study of DME and conventional diesel spray employing a common-rail type fuel injection system with a 5-holes sac type injector (hole diameter 0.168 ㎜/hole) was performed in a high pressure chamber pressurized with nitrogen gas. A CCD camera was employed to capture time series of spray images followed by spray cone angles and penetrations of DME were characterized and compared with those of diesel. Under atmospheric pressure condition, regardless of injection pressure, spray cone angles of the DME were wider than those of diesel and penetrations were shorter due to flash boiling effect. Tip of the DME spray was farmed in mushroom like shape at atmospheric chamber pressure but it was disappeared in higher chamber pressure. On the contrary, spray characteristics of the DME became similar to that of diesel under 3MPa of chamber pressure. Hole-to-hole variation of the DME spray was lower than that of diesel in both atmospheric and 3MPa chamber pressures. At 25MPa and 40MPa of DME injection pressures, regardless of chamber pressure, intermittent DME spray was observed. It was thought that vapor lock inside the injector was generated under the two injection pressures.