• Geomechanics and Engineering
• /
• 제29권3호
• /
• pp.259-267
• /
• 2022

The rheological and penetration characteristics of sodium alginate and xanthan gum aqueous solutions were analyzed for the development of biopolymer-based injection materials. The results of viscosity measurements for the rheological characteristics analysis show that all aqueous biopolymer solutions exhibit a tendency for shear-thinning, i.e., the apparent viscosity decreases as the shear rate increases. In addition, a regression analysis using several models (Power-law, Casson, Sisko, and Cross) was applied to the shear-thinning fluid analysis results, the highest accuracy was determined by applying the power-law model. The micromodel experiment for the penetration characteristics analysis determined that all biopolymer aqueous solutions show higher pore saturation than water, and that pore saturation tends to increase as the flow rate and concentration increases. When comparing the rheological and penetration characteristics of the biopolymer aqueous solution used in this study, the xanthan gum aqueous solution showed a fully developed shear-thinning tendency, unlike the sodium alginate aqueous solution. This tendency is considered to have the advantage of enhancement injectability and pore saturation.

• 한국지반공학회논문집
• /
• 제23권3호
• /
• pp.133-140
• /
• 2007

DCM공법(심층혼합처리 공법)은 흙막이 벽체 등 구조물 조성에 적용하였다. 이러한 DCM 벽체는 경질층에서 관입능력이 있어야 한다. DCM 장비에 부착된 교반날개에 의해 경질지반의 관입능력이 증가되는 알아보기 위해 특수교반날개가 고안되었다. 경질점토층에 관입되는 특수교반날개의 관입특성은 김해와 인천현장에서 조사하였다. 고안한 특수교반날개는 관입속도가 다소 느려도 N=30 이상 되는 지반까지 관입되었고 관입시 효율이 경질지반에서 낮아질 수 있으므로 경제적인 교반날개의 관입깊이를 분석하였다.

• 한국분무공학회지
• /
• 제25권2호
• /
• pp.74-80
• /
• 2020

The jet in crossflow is a spray method used in the various air-breathing engine. In order to understand the spray characteristics in various environments, many prior studies have been conducted. However, there is a lack of understanding of the low-temperature liquid spray characteristics below 273 K. With this in mind, we tried to enhance the knowledge of the low-temperature liquid spray characteristics by identifying the penetration height of low-temperature ethanol. The experiment was conducted under phase pressure, and 273 K of air and 293, 263, and 233 K of ethanol was used. Shadowgraphy was employed to measure the liquid penetration, and Otsu's method was used to analyze the penetration height. The heights tend to decrease as the temperature of the liquid jet decreases. A correlation for the penetration height in the experimental conditions was derived and presented.

• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 2004년도 추계 학술발표회 제16권2호
• /
• pp.809-812
• /
• 2004

The evaluation of characteristics of concrete coated by high performance surface penetration agency was examined through various tests, i.e., compressive strength, penetration depth, water and air permeability, absorption according to various high performance surface penetration agencies and various compressive strengths of base concrete. The 4 types of high performance surface penetration agencies were used i.e., organic, inorganic, water soluble, and alcohol soluble. And 3 types of compressive strength of base concrete were used such as 21, 24 and 30 MPa. The characteristics of concrete coated high performance surface penetration agency was more improved than that of non-coated concrete, and especially, water soluble inorganic agency was most effective. And if compressive strength of base concrete was low, the improved effects would be larger.

• 한국지반공학회:학술대회논문집
• /
• 한국지반공학회 2003년도 봄 학술발표회 논문집
• /
• pp.701-708
• /
• 2003

Recently, piezocone penetration test is frequently conformed in order to estimate the characteristics of soft ground with standard penetration test, generally used in the past. The soil characteristics, such as cone penetration resistance, friction resistence and excessive pore water pressure, can be evaluated continuously through the piezocone penetration test. In Incheon International Airport 2nd phase site preparation, standard penetration test and piezocone penetration test were used in order to increase the confidence for determination of soft ground depth. And the compressible layer was determined by the comparison between the preconsolidation pressure and the designed increase pressure. As the results, the relation between standard penetration test and piezocone penetration test shows q$_{c}$=(1.09~l.63)N at the soft ground, determined by 5/30 N value. And q$_{c}$=(1.21~l.98)N was shown at the point of compressible layer, evaluated by the preconsolidation pressure. These results were applied to determination for the depth of soft ground and to design the improvement for the soft clay.lay.

• 한국해양공학회지
• /
• 제13권3호통권33호
• /
• pp.36-48
• /
• 1999

Fatigue life and crack retardation behavior after penetration were experimentally examined using surface pre-cracked specimens of aluminium alloy 5083. The Wheeler model retardation parameter was used successfully to predict crack growth behavior after penetration. By using a crack propagation rule, the change in crack shape after penetration can be evaluated quantitatively. Advanced, waveform-based acoustic emission (AE) techniques have been successfully used to evaluate signal characteristics obtained form fatigue crack propagation and penetratin behavior in 6061 aluminum plate with surface crack under fatigue stress. Surface defects in the structural members are apt to be origins of fatigue crack growth, which may cause serious failure of the whole structure. The nondestructive analysis on the crack growth and penetration from these defects may, therefore, be one of the most important subjects on the reliability of the leak before break (LBB) design. The goal of the present study is to determine if different sources of the AE could be identified by characteristics of the waveforms produced from the crack growth and penetration. AE signals detected in four stages were found to have different signal per stage. With analysis of waveform and power spectrum in 6061 aluminum alloys with a surface crack, it is found to be capabilities on real-time monitoring for the crack propagation and penetration behavior of various damages and defects in structural members.

• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 2008년도 추계 학술발표회 제20권2호
• /
• pp.401-404
• /
• 2008

균열은 콘크리트에 염소이온과 같은 유해한 물질의 침투경로가 되어 내구성에 심각한 열화를 야기한다. 따라서 고내구성 재료를 사용한 콘크리트 휨부재에서의 균열 발생에 따른 염소이온 침투특성을 검토하고자 하였다. 이를 위해, 고내구성 재료를 적용한 보에 하중을 가하여 휨균열을 도입시키고, 촉진 염화물 침투실험(RCPT)과 장기 염화물 침투실험을 실시하여 염화물 침투 특성을 파악하였다. 실험결과에 따르면, 고내구성 재료를 적용한 부재는 균열이 발생하여도 일반 콘크리트 부재에 비해 높은 염화물 침투 저항성을 보였다. 특히 고로슬래그 미분말을 적용한 경우, 균열 부재의 장기 염화물 침투 실험에서 탁월한 염화물 침투 저항성을 보였다.

• 한국레이저가공학회지
• /
• 제5권1호
• /
• pp.33-42
• /
• 2002

In order to investigate the characteristics of the plasma induced by lap-joint CO$_2$ laser welding of automotive steel sheets, the effects of welding speed, shield gas flow rate, gap size, and laser beam defocus to plasma intensity emitted from keyhole have been investigated. The plasma light is measured by fiber and photodiode. Also, the plasma images were captured by the high speed digital camera in 1000frames/sec in order to correlate the plasma light signal with plasma pattern. From the results, it is observed that the difference of the plasma intensity for between the deep penetration and partial penetration exists from 1.2 to 2 times. The plasma light intensity decreased in case of the deep penetration Is observed due to the exhausting of the plasma gas under the sheet. On the other hand, under the conditions of the deep penetration, the plasma intensity is significantly increased by controling the conditions decreasing the penetration depth. It was specially founded that the effect of 0.3mm gap size at partial penetration condition is approximately similar to deep penetration in 0mm gap. It is concluded that the plasma intensity is able to evaluate the penetration depth in lap-joint welding and appears to offer the most straightforward correlation to the welding process.

• Journal of Pharmaceutical Investigation
• /
• 제36권6호
• /
• pp.401-403
• /
• 2006

Topical preparations such as cream for Acyclovir(ACV), a potent anti-viral agent for the treatment of herpes simplex and herpes zoster, have been marketed in the world since 1993. However, the skin penetration rate of ACV from generic cream formulations sold in Europe has been found to be lower than the original $Zovirax^{\circledR}$ cream. In this study, we formulated ACV into a novel organogel system and compared the skin penetration characteristics with $Zovirax^{\circledR}$ cream. The rate and amount of skin penetration of ACV from the organogels were 6.3-fold greater than those obtained with $Zovirax^{\circledR}$ at an ACV concentration of 5%. The solubilizing effect of oil phase and anti-nucleation effect exhibited by sodium alginate contained in water phase are most likely attributed to enhanced ACV skin penetration property.

• 한국마린엔지니어링학회:학술대회논문집
• /
• 한국마린엔지니어링학회 2002년도 춘계학술대회논문집
• /
• pp.67-73
• /
• 2002

The characteristics of fuel spray influence on the engine performances such as power, fuel economy and emissions. therefore, the measurement of fuel spray characteristics is very important for the improvement of heat engine. The factor which controls the fuel spray is injection pressure, ambient pressure, engine speed et al.. In :his study, We measured spray angle, spray penetration and spray tip velocity considering injection pressure(10,14㎫), ambient pressure(3,4,5㎫), fuel pump speed(500,700,900rpm) in the high temperature and pressure chamber. Experimental results are summarized as follows: 1) Injection pressure influence on the characteristics of spray namely As Injection pressure Is increased, spray angle is decreased but spray penetration and spray tip velocity is increased. 2) Spray angle, spray penetration is increased by increasing the fuel pump speed. 3) Ambient pressure plays an important role in spray characteristics.