• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2001년도 춘계학술대회 논문집
• /
• pp.784-789
• /
• 2001

In order to investigate the fracture behaviors(penetration modes) and the resistance to penetration during ballistic impact of cold-rolled Al 5052 H34 alloy laminates, anodized Al 5052 H34 alloy laminates, and Al 5052 H34 alloy after cold-rolling, ballistic testing was conducted. In general, superior armor material is brittle materials which have a high hardness. Ballistic resistance of these materials was measured by protection ballistic limit(V50), a statical velocity with 50% probability for incomplete penetration. Fracture behaviors and ballistic tolerance, described by penetration modes, are observed respectfully, resulting from V50 test and Projectile Through Plate(PTP) test at velocities greater than V50. PTP tests were conducted with 0$^{\circ}$obliquity at room temperature using 5.56mm ball projectile. V50 tests with 0$^{\circ}$obliquity at room temperature were also conducted with projectiles that were able to achieve near or complete penetration during PTP tests. Surface Hardness, resistance to penetration, and penetration modes of Al 5052 H34 alloy laminates compared to those of cold-rolled Al 5052 H34 alloy laminates and anodized Al 5052 H34 alloy laminates anodized Al 5052 H34 alloy after cold-rolling.

• 비파괴검사학회지
• /
• 제3권1호
• /
• pp.26-30
• /
• 1983

Tests on Liquid Penetrant products normally utilized in the temperature range $10^{\circ}C\;to\;40^{\circ}C$ have shown that the required sensibility can not be obtained at temperatures lower than $10^{\circ}C$ with the penetration and development time usually specified in the operating procedures. It is thus confirmed that $10^{\circ}C$ is the lowest allowable temperature for use of these products. The results obtained with a penetrant and develope. specially formulated for low temperatures (SHERWIN B 305+D100) are satisfactory between $0^{\circ}C\;and\;15^{\circ}C$.

• 한국철도학회:학술대회논문집
• /
• 한국철도학회 2001년도 춘계학술대회 논문집
• /
• pp.451-458
• /
• 2001

The purpose of this study was to evaluate shear parameters on cutting slope of weathered granite soils by using small dynamic cone penetration test on the very moment of its cutting. The results were : On the relations among N$\_$c/, Li, and CEC, the condition of Li＞6%, CEC＞14(meq/100g) corresponds to that of N$\_$c/ values of 2∼30, and 3＜CEC＜14(meq/100g) to N$\_$c/=30∼50. Comparing the smallest penetration depth from two small dynamic cone penetration tests done at 5m below from the top of the slope on April 15th, October 31t. there was a l0cm difference. So we could find out the degree of weathering on the slope. And dividing the difference by 190 days (the whole testing time), we could know it's being weathered 0.052mm each day. The more N. value increases, the more shear parameters(internal friction angle ; $\phi$, cohesion : c) increase at a standard pressure($\sigma$＞32㎪). So the condition of N$\_$c/=2∼50 corresponds to that of $\phi$=27∼50, c=12∼49㎪. From the above testing results, the N$\_$c/ values more correspond to $\phi$ values than c values. In conclusion, this study suggests that on small dynamic cone penetration test a penetration boundary line of 5 centimeters is decided at around Li=4%, CEC=3(meq/100g) which is classified as a strong weathering soil. It also shows that as Li increases CEC increases as well, while N$\_$c/ decreases.

• 비파괴검사학회지
• /
• 제30권3호
• /
• pp.212-224
• /
• 2010

The usefulness of the magnetic camera for non-destructive testing of aging aircraft is discussed in this paper. The magnetic camera can be used f magnetic particle testing(MT), magnetic flux leakage testing(MFLT), eddy current testing(ECT) and penetration testing(PT). It measures the distribution of a magnetic field and visualizes the magnetic pattern. Near and far side cracks, fatigue, thickness degradation, and cracks under rivets have been detected. The possibility of quantitative evaluation was also examined. Using indirect experiments, we verified the detection ability of the sensor for cracks in titanium and advanced composite materials.

• International Journal of Computer Science & Network Security
• /
• 제23권6호
• /
• pp.169-175
• /
• 2023

Ethical hackers are using different tools and techniques to encounter malicious cyber-attacks generated by bad hackers. During the software development process, development teams typically bypass or ignore the security parameters of the software. Whereas, with the advent of online web-based software, security is an essential part of the software development process for implementing secure software. Security features cannot be added as additional at the end of the software deployment process, but they need to be paid attention throughout the SDLC. In that view, this paper presents a new, Ethical Hacking - Software Development Life Cycle (EH-SDLC) introducing ethical hacking processes and phases to be followed during the SDLC. Adopting these techniques in SDLC ensures that consumers find the end-product safe, secure and stable. Having a team of penetration testers as part of the SDLC process will help you avoid incurring unnecessary costs that come up after the data breach. This research work aims to discuss different operating systems and tools in order to facilitate the secure execution of the penetration tests during SDLC. Thus, it helps to improve the confidentiality, integrity, and availability of the software products.

• 한국도로학회논문집
• /
• 제14권5호
• /
• pp.85-91
• /
• 2012

PURPOSES: In this study, various laboratory tests were performed to investigate the suitability of wasted vinyl as a modifier of asphalt binder. METHODS: Based on the ASTM specification, variations in material properties of asphalt binder such as penetration, flash point, softening point, ductility, penetration index (PI), and performance grade (PG) with vinyl content were tested and analyzed. RESULTS: Lavoratory tests revealed that penetration and ductility of the asphalt binder increased with the vinyl content. The flash point, softening point, and PI decreased, and PG changed from 64-22 to 70-22 with increase of the vinyl content. CONCLUSIONS: Wasted vinyl modified the material properties of the asphalt binder. However, the asphalt binder with vinyl content over 6.0% was unsuitable as a pavement material.

• 한국정밀공학회지
• /
• 제20권12호
• /
• pp.126-134
• /
• 2003

In order to investigate the effect of surface treatment in Aluminium alloy and Titanium alloy which are used to armor material during ballistic impact, a ballistic testing was conducted. Anodizing was used to achieve higher surface hardness of Aluminium alloy and Iron plating in PVD(Physical Vapor Deposition) method was used to achieve higher surface hardness of Titanium alloy. Surface hardness test were conducted using a Micro victor's hardness tester. Ballistic resistance of these materials was measured by protection ballistic limit(V-50), a statical velocity with 50% probability penetration. Fracture behaviors and ballistic tolerance, described by penetration modes, are respectfully observed from the results of V-50 test and Projectile Through Plates (PTP) test at velocities greater than V-50. PTP tests were conducted with 0$^{\circ}$obliquity at room temperature using 5.56mm ball projectile. V-50 tests were conducted with 0$^{\circ}$obliquity at room temperature with projectiles that were able to achieve near or complete penetration during PTP tests. Surface hardness, resistance to penetration. and penetration modes of surface treated alloy laminates are compared to those of surface non-treated alloy laminates. A high speed photography was used to analyze the dynamic perforation phenomena of the test materials.

• Journal of Information Processing Systems
• /
• 제11권1호
• /
• pp.104-115
• /
• 2015

Along with the evolution of Internet and its new emerging services, the quantity and impact of attacks have been continuously increasing. Currently, the technical capability to attack has tended to decrease. On the contrary, performances of hacking tools are evolving, growing, simple, comprehensive, and accessible to the public. In this work, network penetration testing and auditing of the Redhat operating system (OS) are highlighted as one of the most popular OS for Internet applications. Some types of attacks are from a different side and new attack method have been attempted, such as: scanning for reconnaissance, guessing the password, gaining privileged access, and flooding the victim machine to decrease availability. Some analyses in network auditing and forensic from victim server are also presented in this paper. Our proposed system aims confirmed as hackable or not and we expect for it to be used as a reference for practitioners to protect their systems from cyber-attacks.

• Structural Engineering and Mechanics
• /
• 제89권3호
• /
• pp.301-308
• /
• 2024

Concrete carbonation is a continuous and slow process from the outside to the inside, in which its penetration slows down with the increased depth of carbonation. In this paper, the results of the evaluation of the measurement of concrete carbonation depth using a non-destructive ultrasonic testing method are presented. According to the results, the relative nonlinear parameter caused more sensitivity in carbonation changes compared to Rayleigh's fuzzy velocity. Thus, the acoustic nonlinear parameter is expected to be applied as a quantitative index to recognize carbonation effects. In this research, combo diagrams were developed based on the results of ultrasonic testing and the experiment to determine carbonation depth using a phenolphthalein solution, which could be considered as instructions in the projects involving non-destructive ultrasonic test methods. The minimum and maximum accuracy of this method were 89% and 97%, respectively, which is a reasonable range for operational projects. From the analysis performed, some useful expressions are found by applying the regression analysis for the nonlinearity index and the carbonation penetration depth values as a guideline.

• Advances in Computational Design
• /
• 제7권1호
• /
• pp.57-68
• /
• 2022

A simulation study of the distribution of magnetic flux induced by a U-shaped electromagnet into a two-layer massive object with variations in the depth and properties of the surface layer has been carried out. It has been established that the hardened surface layer "pushes" the magnetic flux into the bulk of the magnetized object and the magnetic flux penetration depth monotonically increases with increasing thickness of the hardened layer. A change in the thickness and magnetic properties of the surface layer leads to a redistribution of magnetic fluxes passing between the poles of the electromagnet along with the layer and the bulk of the steel object. In this case, the change in the layer thickness significantly affects the magnitude of the tangential component of the field on the surface of the object in the interpolar space, and the change in the properties of the layer affects the magnitude of the magnetic flux in the magnetic "transducer-object" circuit. This difference in magnetic parameters can be used for selective testing of the surface hardening quality. It has been shown that the hardened layer pushes the magnetic flux into the depth of the magnetized object. The nominal depth of penetration of the flow monotonically increases with an increase in the thickness of the hardened layer.