• 한국기계기술학회지
• /
• 제20권6호
• /
• pp.796-802
• /
• 2018

In order to remove rust and impurities from surface of raw SUS circular bar, peeling machine is used to make lustrous and clean surface of SUS circular bar. Drawing process system is used to manufacture SUS hexagonal bar. SUS hexagonal bar have been widely used to make hexagonal bolt/nut, adapter and fittings and so on. The purpose of this study is to investigate the stabilities for guide bar of clamp in drawing process system. As the results, the guide bar showed structural stability in cases of below load of 50 Ton and over hook radius of 3.0mm. Further as the thickness of guide bar hooking with jaw was increased, minimum safety factor was decreased.

• 환경위생공학
• /
• 제18권3호통권49호
• /
• pp.21-26
• /
• 2003

The generation of waste cable has been continuously increased as a production of electrical and communication media are extended. The current recovery methods, such as mechanical peeling, incineration, solvent extraction and pyrolysis, seems inadequate because they are either hard to apply in some cases or environmentally unacceptable. It has been shown that copper can be effectively separated from the jelly filled type cables using a soybean oil treatment method. As a result, jelly compound is vanished from the wire by soybean oil bath and waste wires are separated copper and PE by the mechanical chipper. This is a more environmentally friendly method than burning, and considerably faster than Stripping.

• 한국기계가공학회지
• /
• 제21권1호
• /
• pp.81-89
• /
• 2022

It is necessary to increase the surface hardness and improve the wear resistance and peeling resistance through the surface treatment and performance evaluation of the mold steel. As a result of vacuum heat treatment analysis, residual austenite measurement and surface treatment wear test, retained austenite should be removed by sub-zero treatment, and retained austenite was completely removed by treatment at -196℃. The TiMon film coated on the sub-zero treated STD11 specimen showed the lowest coefficient of friction.

• 반도체디스플레이기술학회지
• /
• 제22권3호
• /
• pp.1-7
• /
• 2023

Recently, in the semiconductor industry, memory device market is focusing on producing ultra-thin wafers for high integration. In the wafer manufacturing process, wafers after backgrinding and CMP process must be picked up as individual dies and subjected to be peeled off from the dicing tape. However, ultra-thin dies are vulnerable to the possibility of breakage and failure in their thickness and size. This research studies the mechanism of peeling a die with a high-aspect ratio using a thermopneumatic method instead of a die ejector with physical pins. Setting compressed air and the temperature as main factors, we determine the success of the digester using thermopneumatic system and analyze the good die to find the possibility of making mass-production equipment.

• 한국자동차공학회논문집
• /
• 제25권3호
• /
• pp.267-272
• /
• 2017

Automotive seat covers with olefin film imported from foreign companies exhibit some problems such as low peeling strength and high burning rate. The traditional manufacturing process requires gas flame or direct heating for the laminating step. This paper introduces an alternative solution that replaces the olefin film and flame lamination method in making automotive seat covers or interior fabrics. We adopt a new manufacturing concept that applies a water-based resin coating to develop a coating system. The coating machine was successfully developed and tested. Results are intended to contribute to improving the quality and productivity of automotive seat cover production.

• 한국군사과학기술학회지
• /
• 제21권4호
• /
• pp.481-488
• /
• 2018

This study suggest the improvement of the CFRP adhesive mixing ratio about acoustic window to enhance SONAR performance. The CFRP of submarine is produced by allocation an acoustic window zone by the beam width of SONAR sensors. During the sea trial, SONAR system's bearing and range accuracy data is not in tolerance due to debonding phenomenon on CFRP. The inappropriate mixing ratio of adhesives caused that peeling phenomenon occurred in the acoustic window part, which is the reason for the deterioration of SONAR sensors performance. The report includes explanation of test procedure of SONAR, root cause analysis, CFRP manufacturing procedure, laboratory tests results, and proof of the performance at the sea trial.

• 유변학
• /
• 제3권1호
• /
• pp.22-29
• /
• 1991

In an effort to predict the long term durability of carbon fiber/epoxy composites in a space environ-ment interlaminar shear strength (ILSS) of the composites was measured as a function of 0.5 MeV electron radiation dosage. For the ILSS measurements a notch method (ASTM D3846) was used with and without side-supports. the supports were used to prevent peeling or bending during the test. The ILSS of both T300/ 5209 longitudinal composite system increases monotonically with radiation when the test is corried out without the support the ILSS of the composites increases initially but then decreases with further radiation. It is also observed that the ILSS of the unsupported case is much lower than that of the supported case. Measurement of epoxy modulus shows that the elastic modulus increases monotonically with radiation. But the breaking strength of the epoxy decreases with radiation. Electron Spectroscopy for Chemcal Analysis shows that the oxygen contents at both the pure epoxy surface and the composite fracture surface increase with radiation dose resulting in the increase of polarity at the interfacial region. This may be a supporting evidence for the increase in the ILSS of the composites.

• 한국융합학회논문지
• /
• 제11권1호
• /
• pp.175-180
• /
• 2020

본 연구에서는 미세패턴 성형이 가능하도록 개발된 초음파 미세패턴 제조시스템을 이용하여 RFID TAG 안테나 형상의 미세패턴 성형기술을 개발하였다. 미세패턴 제조시스템에 종진동 모드의 초음파 공구 혼을 설치하여 절연시트 표면에 RFID TAG 안테나 형상의 미세패턴 안테나 형상을 초음파 압입 성형공정 기술을 개발하였다. 초음파 성형기술은 60kHz 공구 혼을 공진설계 기법을 적용하여 제작하였고, 미세패턴 제조시스템을 이용하여 200㎛ 이하의 절연 시트지에 두께가 25㎛의 코일 와이어를 초음파 압입 성형을 할 수 있다. 초음파 압입 성형 시 코일 와이어의 단선, 박리 및 꼬임 현상 없이 최소선폭 150㎛인 안테나 형상을 성형할 수 있었다.

• 전기화학회지
• /
• 제21권2호
• /
• pp.28-38
• /
• 2018

복합전극의 결착특성은 리튬이차전지의 장기신뢰성 확보와 고에너지밀도 구현을 위한 중요한 물성임에도 불구하고, 측정 기술의 한계로 관련 연구가 제한적이었다. 하지만, $1{\sim}1000{\mu}m$ 두께의 코팅층을 절삭 및 박리하면서 결착특성을 측정할 수 있는 SAICAS(Surface And Interfacial Cutting Analysis System)란 장비의 출현으로 전극 결착특성 연구가 활발해지고 있다. 따라서, 본 총설에서는 SAICAS를 이용한 복합전극의 결착특성 분석 원리 및 측정 방법뿐만 아니라, Peel Test와 같은 기존 결착특성 분석 방법과 비교함으로써 SAICAS를 이용한 분석 방법의 신뢰성 검증 결과를 제시한다. 또한, 전극 설계의 최적화, 신규 바인더 도출 연구, 복합전극 내 바인더 분포 등의 연구에서 SAICAS가 적용된 사례를 소개한다. 이를 통해 SAICAS를 이용한 분석 방법이 리튬이차전지용 복합전극의 결착특성 분석에 용이하게 적용될 수 있음을 제안한다.

• Journal of Biosystems Engineering
• /
• 제26권3호
• /
• pp.271-278
• /
• 2001

Many workers in the garlic peeling factory are separating the sound peeled garlics from the unpeeled and defective ones in a manual way. In order to reduce the seasonal labor requirement and operating cost, the mechanized garlic sorting system such as the vision-based garlic sorter should be developed. This study was conducted as one of basic studies on developing quality evaluation technique for peeled garlics, especially to developed the system for acquiring the whole surface images of garlics with a CCD camera. The following results were obtained from this study. 1. The belt-type garlic rotation system was devised to apply for the vision-based garlic sorter and was tested to decide the criteria of design and optimum conveying speed. 2. To evaluate the performance of the developed garlic rotation system, feeding rate and rotating rate were measured under the conditions of four experimental factors such as the inclined angle of rotating belt, the inclined angle of feeding belt, the height of plate arrays on feeding belt and the conveying speed of belts. And the capacity of the system according to mixture ratios of peeled garlics and unpeeled garlics was analyzed as a feasibility test. 3. For the inclined angle of rotating belt 20°and height of plate array on feeding belt 22㎜, the maximum rotating rate for garlic samples including unpeeled ones was 81.1% at the conveying speed of 4.2 garlic/sec. And under these condition, the maximum feeding rate was 85% at the inclined angle of feeding belt 6.5°. 4. The capacity of the developed garlic rotation system was almost constant regardless of mixture ratio of peeled garlics and unpeeled garlics and its range was 2.95∼3.92 garlic/sec. At the conveying speed of 4.2 garlic/sec, the capacity of the garlic rotation system was calculated ad 58∼64 kg/hr. 5. To improve performance of the garlic rotation system, it is recommended to develop a device to slide garlics into feeding belt.