• International Journal of Korean Welding Society
• /
• 제2권1호
• /
• pp.25-28
• /
• 2002

In the coarse grain HAZ adjacent to the fusion line, most of the TiN particles in conventional Ti added steel are dissolved and austenite grain growth is easily occurred during welding process. To avoid this difficulty, thermal stability of TiN particle is improved by increasing the nitrogen content in steel. In this study, the effect of hlgh nitrogen TiN particle on preventing austenite grain growth in HAZ was investigated. Increased thermal stability of TiN particle is helpful for preventing the austenite grain growth by pinning effect. High nitrogen TiN particle in simulated HAZ were not dissolved even at high temperature such as 1400'E and prevented the austenite grain growth in simulated HAZ. Owing to small austenite grain size in HAZ the width of coarse grain HAZ in high nitrogen TiN steel was decreased to 1/10 of conventional TiN steel. Even high heat input welding, the microstructure of coarse grain HAZ consisted of fine polygonal ferrite and pearlite and toughness of coarse grain HAZ was significantly improved.

• 한국주조공학회지
• /
• 제6권2호
• /
• pp.93-103
• /
• 1986

It is very important to obtain wear resistant ductile iron by adding more economical alloying elements. In this study, 10 heat of Mg-treated ductile iron were made according to Sb content (0-0.1% Sb). Each melt was tasted to 30 ${\o}test$ bars in $CO_2$ mold under the same condition and inspected wear characteristics, mechanical properties and microstructures. The results obtained from this study are as follows; 1. It is confirmed that Sb should be a simple and useful additive for improving wear resistance in ductile iron. 2. Hardness of ferrite and pearlite is improved with increasing Sb amount in ductile iron. 3. For ductile iron, the recommended ladle addition of Sb amount is to 0.02-0.03%. 4. Sb has adverse influence on spheroidizing of graphite if the amount is over 0.04%.

• 한국건축시공학회:학술대회논문집
• /
• 한국건축시공학회 2019년도 춘계 학술논문 발표대회
• /
• pp.182-183
• /
• 2019

In this study, the optimization of mixing proportion of press-forming board with blast furnace slag, pearlite and bottom ash was investigated using the response surface methodology. Ten Mixing proportions of specimens were designed by the response surface design, and then flexural failure load, moisture content and water absorption of specimens were measured. As a result of the reaction surface analysis based on the experimental results, it was possible to derive the optimal mixing proportion with the satisfaction of 93%.

• 한국공작기계학회:학술대회논문집
• /
• 한국공작기계학회 1996년도 춘계학술대회 논문집
• /
• pp.143-148
• /
• 1996

In this paper, we have studied internal quality including chemical compositions, microscopic structure and nonmetalic inclusion of test materials. We have analyzed dynamic characteristics of cutting force of milling including tensile strength value hardness etcs. Test materials are used the tempered carbon steel and the non-tempered carbon steel. The obtained results are as follows: 1.In analyzing internal quality, the tempered carbon steel have typical martensite structure and the non-tempered carbon steel have ferrite+pearlite structure. 2.Yield strength, tensile strength and hardness value are in the non-tempered carbon steel but elongation is maximum value in the tempered carbon steel. 3.Cutting force is smaller non-tempered carbon steel than tempered carbon steel when feed speed and depth of cut is constant. 4.Cutting force is smaller to the tempered carbon steel and smaller non-tempered carbon steel than tempered carbon steel when cutting conditions

• International Journal of Naval Architecture and Ocean Engineering
• /
• 제9권1호
• /
• pp.66-76
• /
• 2017

This paper is concerned with investigating the plastic material properties of steel plate formed by line heating method, and is aimed at implementing more rational design considering the accidental limit states such as collision or grounding. For the present study, line heating test for marine grade steel plate has been carried out with varying plate thickness and heating speed, and then microscopic examination and tensile test have been carried out. From the microscopic, it is found that the grain refined zones like ferrite and pearlite are formed all around the heat affected zone. From the tensile test results, it is seen that yield strength, tensile strength, fracture strain, hardening exponent and strength coefficient vary with plate thickness and heat input quantity. The formulae relating the material properties and heat input parameter should be, therefore, derived for the design purpose considering the accidental impact loading. This paper ends with describing the extension of the present study.

• 한국재난정보학회:학술대회논문집
• /
• 한국재난정보학회 2015년 정기학술대회
• /
• pp.138-140
• /
• 2015

건축물에서 단열재는 일정한 온도를 유지하도록 하려는 부분의 바깥쪽을 피복하여 외부로의 열손실이나 열의 유입을 적게 하기 위한 재료이다. 단열재는 소재(素材) 자체의 열전도율(熱傳導率)이 작은 것이 바람직하나, 대부분 열전도율이 그다지 작지 않다. 그러므로 대개의 경우 열전도율을 작게 하기 위해서 다공질(多孔質)이 되도록 만들어 기공(氣孔) 속의 공기의 단열성을 이용한다. 일반적으로 재료의 밀도가 크면 열전도율 값이 크게 되는 경향이 있다. 이에 본 연구에서는 경량골재인 펄라이트의 입자 크기별 열전도율을 측정하여 단열재로서 사용여부를 판단하고자 한다.

• 열처리공학회지
• /
• 제3권2호
• /
• pp.37-44
• /
• 1990

The effect of the microstructural change on the near threshold fatigue crack growth rate in SM40C steel has been studied using the ${\Delta}K$ decreasing method. Below the total strain amplitude of 0.56%, cyclic softening occured, whereas above this value cyclic hardening occurred in the pearlitic lamellar structure. However, in the spherodized structure the cyclic hardening solely occurred. The crack growth rate in the near-threshold region was decreased with increasing prior austenite grain size and this was due to surface roughness. The crack growth rate of the spherodized structure was lower than that of the pearlite lamellar structure and the ${\Delta}K_{th}$ of the former was higher than that of the latter. It was understood that the crack propagates preferentially through the ferrite phase. The intergranular facets in the near-threshold region appeared in the spherodized structure.

• Corrosion Science and Technology
• /
• 제20권5호
• /
• pp.242-248
• /
• 2021

Unforeseen failures of boilers in power plants may affect the continuation of electricity generation. Main failures in boilers are influenced by the tube material, tube position, boiler service temperature and pressure, and chemical composition of the feed water and coal. This investigation was intended to find answers on the causes and mechanism of failure of the fire-side boiler water-wall tubes, due to perforation and corrosion. The tube conformed to the material requirements in terms of its chemical composition and hardness. Microscopic examination showed ferrite and pearlite indicating no changes in its microstructure due to the temperature variation. SEM test showed a single layer and homogenous film density particularly on the area far from perforation. However, layers of corrosion product were formed on the nearby perforation area. EDX showed that there were Na, Ca, S, and O elements on the failed surface. XRD indicated the presence of Fe₂O₃ oxide. The failure mechanism was identified as a result of significant localized wall thinning of the boiler water wall-tube due to oxidation.

• 한국정밀공학회지
• /
• 제14권7호
• /
• pp.22-28
• /
• 1997

In this paper, We have studied internal quality incluiding chemical compositions, microscopic structure and nonmetalic inclusion of test material. We have analyzed dynamic characteristics of cutting resistence and compared chip treatment of the test material. In analyzing internal quality, all of the test material have typical ferrite+pearlite structure. But, nonmetallic inclusion has oxide and sulfide inclusion has oxide and sulfide inclusion in medium carbon steel, mainly sulfide inclusion is existed in S-free cutting steel. In Ca+S-free cutting steel, calcium aluminate and sulfide complex inclusion, had low-melting point, as deformation of sulfide and oxide inclusion is existed. Machining characteristics, cutting resistence is maximum in medium carbon steel. Chip treatement are excellent in S-free cutting steel, similar to the Ca+S free cutting steel and medium carbon steel.

• 현장농수산연구지
• /
• 제23권2호
• /
• pp.63-70
• /
• 2021

파종 후 60일 지난 인삼 생장율 조사 평균 초장은 16.9cm, 평균 초중은 0.54g으로 측정되었다. 각 토양별 생장율은 1번(피트모스6.5:펄라이트2:마사토1.5) 구에서는 16.36cm, 0.60g. 2번(피트모스 10) 구에서는 13.74cm, 0.41g. 3번(일반상토10)구에서는 12.43cm, 0.26g. 4번(일반상토8:코코피트2) 구에서는 14.60cm, 0.39g으로 측정되었다. 1번 인공상토에서 평균초장과 초중이 다른 토양 생육환경보다 우수한 것으로 측정되었다. 식물체 분석을 위해 인공상토별 평균초장과 초중이 우수한 피트모스6.5:펄라이트2:마사토1.5 비율의 인공상토와 상대적으로 낮은 결과의 일반상토에서 자란 인삼식물체 각 30개를 선별하여 식물체 분석을 수행하였다. 그 결과 1번 실험구(피트모스6.5:펄라이트2:마사토1.5) 속의 질산태 질소(NO₃-N) 260ppm이나 1번 시험구(일반상토10)에서 생육된 인삼 식물체는 질산태 질소(NO₃-N) 1,040ppm으로 더 높게 나타났다. 인삼의 특징은 질소 함량이 300ppm 넘어가면 생육이 불량해진다. 인산(P), 칼륨(K), 마그네슘(Mg)에서는 큰 차이가 없었다.