• Journal of Power Electronics
• /
• 제17권2호
• /
• pp.315-322
• /
• 2017

LED is a promising new generation of green lighting with the advantages of high efficiency, good optical performance, long lifetime and environmental friendliness. A pulsating current can be used to drive LEDs. However, current with a high peak-to-average ratio is unfavorable for LEDs. A novel control scheme for the ac-dc critical conduction mode (CRM) flyback LED driver is proposed in this paper. By using the input voltage, output voltage and average output current to control the turn-on time of the switch, the peak-to-average ratio of the output current can be reduced. The operation principle is analyzed and an implementation circuit is put forward. Experimental results show the effectiveness of the proposed scheme.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2000년도 하계학술대회 논문집 C
• /
• pp.1569-1571
• /
• 2000

The ageing process was checked by leakage current monitoring in Salt Fog Method. In order to monitor leakage current, DAS with 12-bit, 8-channel A/D converter was prepared. The monitored components of leakage current were averages of the rms and peak, max peak, cumulative charge, and the cumulative number of peak pulses. The acquired data were stored to the disc periodically. And, surface conductivity was measured to investigate loss of hydrophobicity. The results suggest that surface conductivity and leakage current are well corresponding to initial loss of hydrophobicity.

• 한국전기전자재료학회논문지
• /
• 제27권2호
• /
• pp.104-109
• /
• 2014

To operate organic light emitting device (OLED) with alternating current (AC) power source without AC/DC(direct current) converter, we fabricated the fluorescent OLED and measured the emission characteristics with AC and DC. The OLED operated by AC showed higher maximum current efficiency of 8.2 cd/A and maximum power efficiency of 8.3 lm/W. But current efficiency and power efficiency of AC driven OLED showed worse than DC driven OLED at high voltage above 10 V. This result can be explained by the peak voltage of AC was $\sqrt{2}$ times than DC, In case of low driving voltage the emission characteristics were improved by the peak voltage of AC, but in case of high driving voltage the emission efficiencies were decreased by the roll off phenomena. Finally, serial OLED arrays using twelve OLEDs driven by AC 110 V showed average voltage of 9.17 V, voltage uniformity of 99.0%, average luminance of $1,175cd/m^2$, luminance uniformity of 94.4%.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2002년도 하계학술대회 논문집 Vol.3 No.2
• /
• pp.699-702
• /
• 2002

A DC current sensor is disclosed in which two pairs of saturable cores are provided so as enclose a conductor carrying a direct current to be measured. On each of the saturable cores, a bias winding, a feedback winding and an output winding are wound. Circuit for detection of an asymmetry in the magnetization current, generated by a reference alternating voltage, in a signal-conditioner. The reference alternating voltage is fed to the respective series circuits such that no resultant induction current is induced in the modulating current. The voltages over the resistor form input signals for two peak value detectors, the strength of the output signal of which represents the degree of asymmetry of magnetization current. This paper describes the development a DC current sensor and its signal-conditioner.

• Journal of information and communication convergence engineering
• /
• 제8권5호
• /
• pp.566-569
• /
• 2010

This paper describes the sinusoidal, pulse, triangular oscillator using second generation current conveyor. To obtain the sinusoidal waveform the circuit blocks are constructed by using all pass filter and integrator. The pulse and the triangular waveforms are obtained from the output of sinusoidal oscillator. The peak-to-peak voltages of sinusoidal and triangular waveforms can be easily controlled by the dc offset voltage. Also the output frequency of the oscillator can be controlled by varying passive elements. The designed circuit is verified by HSPICE simulation.

• 전력전자학회:학술대회논문집
• /
• 전력전자학회 2003년도 추계학술대회 논문집
• /
• pp.230-233
• /
• 2003

Simulation model of induction type fixed speed wind power generator is developed. It is shown that the peak value of inrush current during start up changes according to the firing angle control strategy of soft starter. New proposed firing angle control scheme showed $25\%$ of reduction of peak current which results in smaller drop of gird voltage at the point of common coupling during start up.

• 한국산학기술학회논문지
• /
• 제14권5호
• /
• pp.2315-2321
• /
• 2013

본 연구는 혈류에 의한 조영제 peak time을 산출하는 새로운 방법을 개발하여 기존의 수식에 의한 부작용을 최소화 하고, 대체할 수 있는 새로운 검사법을 제시하고자 하였다. 시험적조영제주입법을 이용하여 CE MRA를 검사한 환자 127명을 대상으로, 기존의 수식에 의해 산출된 조영제 peak time이 조영제 주입 후 혈류에 의한 영상화 범위의 어느 뇌혈관 측정값과 일치하는지 각 뇌혈관의 조영제 inflow time과 peak time을 측정하였다. 연구결과, 유의수준 0.05에 대한 4개의 집단 간 차이가 존재하였으나 집단 1에서 수식에 의해 산출된 조영제 peak time과 S상 정맥동의 조영제 inflow time이 통계적으로 유의한 차이가 없어 일치하였으며, Bland Altman plot를 시행한 결과 일치도가 상당히 높은 것을 확인할 수 있었다. 따라서 본 연구의 혈류에 의한 새로운 방법을 적용한다면, 부작용 가능성을 최소화하고, 영상의 질은 유지하면서, 쉽고 빠르게 적용할 수 있어, 기존의 수식에 의해 산출된 조영제 peak time을 대체 할 수 있으리라 사료된다.

• 상하수도학회지
• /
• 제30권3호
• /
• pp.225-231
• /
• 2016

Peak load rate(i.e., maximum daily flow/average daily flow) has not been considered for industrial water demand planning in Korea to date, while area unit method based on average daily flow has been applied to decide capacity of industrial water treatment plants(WTPs). Designers of industrial WTPs has assumed that peak load would not exist if operation rate of factories in industrial sites were close to 100%. However, peak load rates were calculated as 1.10~2.53 based on daily water flow from 2009 to 2014 for 9 industrial WTPs which have been operated more than 9 years(9-38 years). Furthermore, average operation rates of 9 industrial WTPs was less than 70% which means current area unit method has tendency to overestimate water demand. Therefore, it is not reasonable to consider peak load for the calculation of water demand under current area unit method application to prevent overestimation. However, for the precise future industrial water demand calculation more precise data gathering for average daily flow and consideration of peak load rate are recommended.

• 전력전자학회논문지
• /
• 제19권3호
• /
• pp.220-226
• /
• 2014

Input current ripple and harmonic components of the power device are main causes of electromagnetic interference (EMI). Although the discontinuous conduction mode (DCM) operation can reduce harmonic components of the power device by reducing reverse recovery current of diode and turn-off voltage spikes of the switch, input current ripple increases due to high peak to peak inductor current. Therefore, in this paper, frequency control algorithm is proposed to reduce the input current ripple of DCM operated interleaved boost converter. In the proposed algorithm, duty ratio is fixed either 0.33 or 0.67 to minimize the input current ripple and the switching frequency is controlled according to operating conditions. 600 W 3-phase interleaved boost converter prototype system is built to verify proposed algorithm.

• 한국초전도학회:학술대회논문집
• /
• 한국초전도학회 1999년도 High Temperature Superconductivity Vol.IX
• /
• pp.343-347
• /
• 1999

YBCO film을 이용한 meander 형태의 저항형 한류기에서 고장이 발생하였을 때 초기의 과도상태에서 볼수 있는 첨두전류를 억제하기 위하여 shunt 저항을 병렬로 취부한 경우의 전기적특성을 살펴보았다. 인가전압을 16.5 V$_{peak}$로 가하고 R$_0$는 1 ${\omega}$,R$_L$을 7.7 ${\omega}$으로 하고 shunt 저항을 5 ${\omega}$으로 하였을 때 약 12.2 A$_{peak}$의 전류값에서 최초quench가 발생하였으며 초전도 한류소자에 quench 발생으로 인한 저항이 발생함과 동시에 I$_1$으로 흐르던 사고전류의 일부가 shunt 저항이있는 I$_2$으로 서서히 분로하여 첨두전류가 거의 발생하지 않았다. 이때 초전도 한류기를 적용하지 않은 경우 최대 사고전류는 약 16.5 A$_{peak}$이었으며 초전도 한류기를 적용한 경우는 최대 한류전류값이 9 A$_{peak}$에서 4주기후에는 5.8 A$_{peak}$이었다. 인가전압 V$_0$=113 V$_{peak}$이고 표준저항 R$_0$는 1${\omega}$, 그리고 R$_L$을 7.7 ${\omega}$으로 하고 shunt 저항을 5 ${\omega}$으로 하였을 때 사고각 0 $^{\circ}$에서 사고전류값이 최고 23.0 A$_{peak}$까지 상승하고 이후 일정한 값을 유지하였다. 일반적으로 사고발생 직후에는 전류변화율에 의하여 전류값의 급격한 상승을 보이지만 shunt 저항이 전류분류의 역할을 수행하여 첨두전류는 거의 발생하지 않았다. 또한 상온의 gold층의 저항을 감안했을 때 사고발생후 약 36msec 후에 상온에 도달하였으며 shunt 저항이 없는 경우의 11 msec에 비하여 약 3배이상 길어졌다. 사고각 45 $^{\circ}$와 90 $^{\circ}$인 경우는 반복실험에 의한 시편의 특성저하(degradation)에 의하여 정상상태에서 초전도체에 흐르는 전류가 약간 발생하였다. 계통의 신뢰성이 중요한 요소로 작용하는 실제운전에서는 시편의 특성저하에 의한 quench전류의 감소를 감안하여 적절한 운전조건을 도출하여야 한다. 이상에서 앞으로는 장기간의 실제운전 조건을 고려하여 시편의 특성저하(degradation)와 가혹조건에 대한 전기적 특성에 대한 연구를 병행하고자 한다.