• 한국도로학회논문집
• /
• 제14권2호
• /
• pp.93-99
• /
• 2012

선행 차량과의 상대속도에 따른 차두거리 분포에 관한 연구를 위해 연속류 도로 중 국도에 설치된 차량검지기(VDS, Vehicle Detection System)의 교통정보 수집자료를 분석하였다. 수집자료를 차선별, 방향별로 정렬하여 선행 차량과 후행 차량 사이의 속도차이인 상대속도와 검지기 통과시간 및 차량의 속도를 이용하여 차두거리를 산출하였다. 모든 시간대를 대상으로 산출된 상대속도와 차두거리의 분석을 통해 두 변수간의 관계를 분석한 결과 고르게 분포하고 있는 것으로 나타났고 동일차량군 주행에서 차두거리의 중간값은 약 40m이며, 이는 자료구축 및 분석부분에서 언급한 A~D영역을 분류함에 있어 기준이 될 수 있었다. 시간대에 따른 차두거리 분포에 대한 분석을 위해 수집된 모든 자료의 교통량을 통해 첨두교통량을 산정하고 이를 기준으로 첨두시간과 비첨두시간을 분류하여 차두거리 분포의 차이를 분석하였다. 첨두시간은 비첨두시간에 비해 상대적으로 앞 차량과의 속도 차이가 적고 차두거리가 좁은 것으로 나타났기 때문에 선행차량과 같은 주행 패턴으로 추종한다고 할 수 있고 비첨두시간는 차두거리가 상대적으로 넓은 것으로 나타났다. 이는 운전자의 행태를 나타낼 수도 있는 것으로 차두거리가 좁을수록 공격적인 운전을 하며 본인의 총 통행시간을 줄이고자 하는 욕구가 크다고 미루어 짐작할 수 있겠다. 하지만 여가통행과 비첨두시간의 경우는 첨두시간에 비해 차두거리가 넓은 것으로 미루어보아 시간적 압박이 적어 상대적으로 여유로운 운전행태를 보인다고 할 수 있겠다.

• 한국환경과학회지
• /
• 제24권4호
• /
• pp.393-401
• /
• 2015

Rainfall-runoff model of Jeju Oedo Stream was used to compute the optimal unit hydrograph by HEC-HMS model that reflecting on watershed characteristics. Each rainfall event was comparatively analyzed with the actual flow measurement using Clark, Snyder and SCS synthetic methods for derived unit hydrograph. Subsequently, the null hypothesis was established as p-value for peak flow and peak time of each unit hydrograph by one-way ANOVA(Analysis of variance) was larger than significance level of 0.05. There was no significant difference in peak flow and peak time between different methods of unit hydrograph. As a result of comparing error rate with actual flow measurement data, Clark synthetic unit graph best reflected in Oedo Stream as compared to other methods, and error rate of Clark unit hydrograph was 0.02~1.93% and error rate at peak time was 0~2.74%.

• 방사성폐기물학회지
• /
• 제20권2호
• /
• pp.161-170
• /
• 2022

The effect of oxidation time on the characteristics and mechanical properties of spent nuclear fuel cladding was investigated using Raman spectroscopy, tube rupture test, and tensile test. As oxidation time increased, the Raman peak associated with the tetragonal zirconium oxide phase diminished and merged with the Raman peak associated with the monoclinic zirconium oxide phase near 333 cm^-1. Additionally, the other tetragonal zirconium oxide phase peak at 380 cm^-1 decreased after 100 d of oxidation, whereas the zirconium monoclinic oxide peak became the dominant peak. The oxidation time had no effect on the tube rupture pressure of the oxidized zirconium alloy tube. However, the yield and tensile stresses of the oxidized nuclear fuel cladding tube decreased after 100 d of oxidation. The results of the scanning electron microscopy and transmission electron microscopy were represented with the in-situ Raman analysis result for the oxide characteristics generated on the cladding of spent nuclear fuel.

• 한국전문물리치료학회지
• /
• 제20권3호
• /
• pp.45-53
• /
• 2013

The purpose of this study was to examine the differentiation of proprioception, invertor and evertor muscle strength, and time to peak torque at a velocity of $300^{\circ}/sec$ of the ankle joint in people with or without functional ankle instability (FAI). Nineteen subjects with a history of ankle sprain participated. All subjects were divided into FAI group ($n_1=9$, Cumberland ankle instability tool (CAIT)${\leq}24$) and a control group ($n_2=10$) based on their CAIT scores. Isokinetic dynamometer was used to measure the sense of active joint position of the ankle at mid-range and end-range of an inversion motion and invertor as well as the evertor muscle strength and time to peak torque at $300^{\circ}/s$. The FAI group showed a statistically reduction in invertor and evertor muscle strength and time to peak torque when compared to the control group (p<.05). Muscle strength and time to peak torque of the invertor and evertor, as well as the sense of active joint position at end-range were also lower in the FAI group than in the control (p<.05). Correlations between CAIT score and position sense at end-range (r=-.577) and invertor muscle strength (r=.554) were statistically significant (p<.05). Individuals with FAI showed reduction in invertor and evertor muscle strength and recruitment time as well as in proprioception of the ankle joint. Thus, proprioception and invertor and evertor muscle strength of the ankle joint at fast angular velocity may be investigated when examining and planning care for individuals with FAI.

• 대한전자공학회논문지
• /
• 제17권4호
• /
• pp.38-44
• /
• 1980

본 논문에서는 peak 검출과 average magnitude difference function (AMDF)방법을 이용해서 음성의 주기를 고속도로 추출하는 방법이 연구되었다. 먼저 입력 음성을 800Hz로 대역폭을 줄인다음 Pitch peak가 될 만한 몇개의 Peak을 검출한다. 그 다음 이들 peak들의 값을 갖고 AMDF를 계산해서 이들 값들 중에서 최소의 AMDF치를 갖는 peak를 원하는 음성주기로 결정을 한다. 이 방법을 사용하여 음성의 주기를 검출하면 타 음성주기 추출방법 보다 훨씬 적은 계산 시간이 소요될 분만 아니라 비교적 정확한 결과를 얻을 수 있다.

• 대한한의진단학회지
• /
• 제17권1호
• /
• pp.63-76
• /
• 2013

The aims of this study are to investigate a logisitic regression equation of the vacuous pulse and the replete pulse for efficacy evaluation of clip-type pulsimeter by using magnetic Hall device. To evaluate the efficacy of clip-type pulsimeter by using magnetic Hall device as sensing the minute movement of a radial artery, one research clinical trial have been performed. The number of subject was 120, the clinical data of patients did treated with a normal statistical method. The systolic peak amplitude, the reflective peak amplitude and time, and the notch peak amplitude and time are analyzed major efficacy parameters to discern the vacuous pulse and the replete pulse. The equations included of five parameters such as systolic peak amplitude, the reflective peak amplitude and time, and the notch peak amplitude and notch amplitude time for determination of the vacuous pulse and the replete pulse were deducted by statistical logistic regression method. It suggests that the logistic regression equations are possible to develop the oriental algorithm for pulse diagnosis.

• Wind and Structures
• /
• 제23권4호
• /
• pp.275-300
• /
• 2016

Synchronous multi-pressure measurements were carried out with relatively long time duration for a double-layer reticulated shell roof model in the atmospheric boundary layer wind tunnel. Since the long roof is open at two ends for the storage of coal piles, three different testing cases were considered as the empty roof without coal piles (Case A), half coal piles inside (Case B) and full coal piles inside (Case C). Based on the wind tunnel test results, non-Gaussian time-dependent statistics of net wind pressure on the shell roof were quantified in terms of skewness and kurtosis. It was found that the direct statistical estimation of high-order moments and peak factors is quite sensitive to the duration of wind pressure time-history data. The maximum value of COVs (Coefficients of variations) of high-order moments is up to 1.05 for several measured pressure processes. The Mixture distribution models are proposed for better modeling the distribution of a parent pressure process. With the aid of mixture parent distribution models, the existing translated-peak-process (TPP) method has been revised and improved in the estimation of non-Gaussian peak factors. Finally, non-Gaussian peak factors of wind pressure, particularly for those observed hardening pressure process, were calculated by employing various state-of-the-art methods and compared to the direct statistical analysis of the measured long-duration wind pressure data. The estimated non-Gaussian peak factors for a hardening pressure process at the leading edge of the roof were varying from 3.6229, 3.3693 to 3.3416 corresponding to three different cases of A, B and C.

• 한국기계가공학회지
• /
• 제17권4호
• /
• pp.76-82
• /
• 2018

3D formed Electrical Discharge Machining (EDM) and hole EDM were conducted for die and mold manufacturing with electrodes which were made by mechanical machining and wire EDM. It is difficult to machine the hardened material after heat treatment and quenching with traditional machining. The only method of machining hardened material is die-sinking EDM. In this research, hole EDM was conducted for heat-treated cold-worked tool steel (SKD11) for use as a die material. The EDM surfaces were analyzed by pulse-on time and peak current of EDM current, according to the machining conditions of EDM. The EDM surface profiles were affected by the peak current. The contribution of each factor is peak current (91.63%) and pulse-on time (0.93%). The best surface roughness was obtained with a $130{\mu}s$ pulse-on time and a 14.2 A peak current. With uniform EDM processing, the surface deteriorated with increasing pulse-on time and peak current. The thickness of the solidified layer induced by EDM was increased as the peak current, crater shapes, and erupted shapes of EDM surfaces were increased. Therefore, microcracking gaps induced by surface tension were increased.

• 한국정보과학회논문지:컴퓨팅의 실제 및 레터
• /
• 제12권5호
• /
• pp.312-325
• /
• 2006

EAI나 B2BI와 같은 통합 어플리케이션들은 짧은 시간 동안의 서비스 요청 폭주로 인한 과부하시에도 대용량의 I/O기반 트랜잭션들을 안정적으로 처리할 수 있는 신뢰성 있는 시스템을 필요로 한다. 본 논문에서는 I/O기반 시스템에서 대용량의 거래를 효과적으로 처리할 수 있으며 짧은 시간 동안의 거래 요청 폭주로 인한 과부하시에도 안정적으로 서비스를 제공할 수 있는 Peak Load Control(PLC)기반의 Worker-Linker 패턴을 제시한다. 본 논문에서는 PLC 기법을 위해 지체시간(Delay Time) 알고리즘을 사용한다. 또한 제안한 알고리즘이 가지는 과부하 시의 성능 안정성을 증명하기 위해 본 논문에서는 Worker-Linker 패턴을 실제 B2BI 시스템에 적용해서 성능 안정성을 증명하기 위한 실험 결과를 제시한다. 실험 결과에 의하면 본 논문에서 제안한 지체시간 알고리즘은 과부하 상태를 안정적으로 통제하는데 효과가 있다.

• 대한전기학회논문지:전기물성ㆍ응용부문C
• /
• 제52권1호
• /
• pp.35-41
• /
• 2003

In this paper statistics on the radiation field waveforms produced by stepped leaders just prior to lightning return strokes were described. As a parameter of stepped leader pulse characteristics, the time interval between the final leader pulse and return stroke peak, the pause time between stepped leaders, the ratio of the final leader peak to the return stroke peak and the stepped leader pulse width at half maximum were examined. The average time intervals between the final leader pulse and return stroke peak were about 16.2 and 14.8$mutextrm{s}$ for the positive and negative polarities, respectively. When the stepped leader approaches closely to ground, the time interval between leader steps was decreased and the mean value was about 17$mutextrm{s}$, and the present results were in reasonable agreement with the data observed in Florida and Japan. The large fraction of the ratios of the final stepped leader pulse to the lightning return stroke peak were distributed over the range from 5 to 35% and in average the ratio of the final leader pulse to the return stroke peak was 17.4$\pm$11.9% for the positive and 18.5$\pm$9.4% for the negative electric field waveforms. In addition, the mean pulse widths at half maximum of the stepped leaders are 1.4Us with a standard deviation of 0.9 for the positive Polarity and 2.2us with a standard deviation of 1.2 for the negative polarity, respectively.