• Journal of Korean Foot and Ankle Society
• /
• v.26 no.3
• /
• pp.130-135
• /
• 2022

Purpose: Smart insoles are wearable devices that are inserted into shoes. Smart insoles with built-in pressure and acceleration sensors can measure the plantar pressure, stride length, and walking speed. This study evaluated the validity and reliability of the plantar pressure measurements of smart insoles during walking on flat ground. Materials and Methods: Twenty one subjects were included in this study. After wearing smart insoles, I-SOL^® (Gilon, Seongnam, Korea), the subjects walked a 10 m corridor six times at a rate of 100 steps/min, and the middle three steps, free from direction changes, were chosen for data analysis. The same protocol was repeated after wearing Pedar-X (Novel Corporation, Munich, Germany), an insoletype plantar pressure measurement equipment with proven validity. The average maximum pressure (P_peak, kPa) and the time at which P_peak appeared (P_time, %stride) were calculated for each device. The validity of smart insoles was evaluated by using the interclass correlation coefficient (ICC) of P_peak and P_time between the two instruments, and Cronbach's alpha was obtained from the P_peak values to evaluate the reliability. Results: The ICC of P_peak was 0.651 (good) in the hallux, 0.744 (good) in the medial forefoot, 0.839 (excellent) in the lateral forefoot, and 0.854 (excellent) in the hindfoot. The ICC of P_time showed 0.868 (excellent) in the hallux, 0.892 (excellent) in the medial forefoot, 0.721 (good) in the lateral forefoot, and 0.832 (excellent) in the hindfoot. All ICC values showed good or excellent results. The Cronbach's alpha of P_peak measured in the smart insoles was 0.990 in the hallux, 0.961 in the medial forefoot, 0.973 in the lateral forefoot, and 0.995 in the hindfoot; all indicated excellent reliability in all areas. Conclusion: The plantar pressure measurements of smart insoles during walking on a flat ground showed validity compared to Pedar-X, and high reliability after repeated measurements.

• Progress in Superconductivity and Cryogenics
• /
• v.5 no.1
• /
• pp.111-117
• /
• 2003

In the design of the split type free displacer Stilting cryocooler the motion of the displacer is very important to decide the cooling capacity, which depends upon the working gas pressure, the swept volume in the compression space and the expansion space, operating frequency, the phase shift between piston and displacer, etc. In this study, Stirling cryocooler actuated by the electric farce of the dual linear motor is designed and manufactured. Cool down characteristics of the cold end with laser displacement sensor in the expander of the Stilting cryocooler is evaluated. The charging pressure was 15kg$_{f}$/$\textrm{cm}^2$ and operating frequency was 50Hz. Input power and the lowest temperature were about 32W and 67K, respectively. And, displacement of the piston is measured by LVDTs (Linear Variable Differential Transformers), displacement of thedisplacer is measured by laser optic method, and phase shift between piston and displacer is discussed. As the peak-to-peak pressure of the compressor was increased, peak-to-peak displacement of the displacer was increased. The peak-to-peak displacement of the displacer increases in the range of 0 - 64.5Hz(resonant frequency of the displacer), but decreases steeply when the operating frequency is bigger than the resonant frequency. Finally when the phase shift between displacements of the Piston and displacer is 45。, operating frequency is optimum and is decided by resonant frequency of the expander, mass and cross section area of the displacer and constant by friction and flow resistance.e.

• The Transactions of the Korean Institute of Electrical Engineers
• /
• v.32 no.7
• /
• pp.227-233
• /
• 1983

Noticing that action of gaseous phase in insulating oil concerns to the discharging characteristics, I investigated the smalness pressure effects on quantity of the partial discharge and discharging pulse frequency. Tests are carried out between the niddle points in insulating oil at pressure being changed by gradual charge of inert gas Ar. At pressure as low as of 0.1-0.5 torr pulse frequency and maximum partial discharge reach peak while at pressure haigher than 20 torr no pulse is observed. The fact that pulse frequency has peak value at certain presure, which is changed either by charging Ar or by adding oil, implies that the action of gaseous phase depends on pressure. Test results are that partial discharge pulse are governed by pressure of Ar-charged oil, and less partial discharge pulses correspond to smaller bubbles whereas more partial descharge pulses correspond to larger bubbles.

• Journal of the Korean Society of Safety
• /
• v.14 no.3
• /
• pp.40-47
• /
• 1999

A numerical study on gaseous explosion was carried out to predict the transient pressure behavior with the partial rupture in confined vessels. Equations, assumptions and solutions for central ignition of premixed gases in closed spherical vessels are proposed with various equivalence ratios of gas fuel, as $CH_4$ and $C_3H_8$, vent areas and vent opening pressures. Given vent opening pressure in a vessel, the magnitude of second peak pressure results from the vent areas and burning velocity, varied by equivalence ratio of gas fuel. In a living room of an apartment, the higher second peak pressure than the vent pressure is not appeared due to its large window areas. As vent opening pressure is higher, the larger damage by gaseous explosion is expected and the larger vent area is necessary for relieving the damage. In the same concentration, the gaseous explosion by propane rather than methane shows the larger damage due to its higher adiabatic flame temperature and equivalence ratio.

• International Journal of Concrete Structures and Materials
• /
• v.6 no.1
• /
• pp.31-40
• /
• 2012

Self-consolidating concrete (SCC) is a recently developed innovative construction material. SCC fills in a formwork without any vibrating consolidation, which allows us to eventually achieve robust casting. However, high formwork lateral pressure exerted by SCC is a critical issue regarding its application as cast-in-place concrete. In order to control the risk caused by high formwork pressure, a comprehensive prediction model for the pressure was previously proposed, investigated, and validated with various SCC mixtures. The model was originally designed to simulate the intrinsic pressure response of SCC mixtures while excluding other extrinsic influencing factors such as friction and flexibility of the formwork. The model was then extended to consider extrinsic factors such as friction between SCC mixtures and formwork. In addition, other interesting topics for peak formwork pressure and mineral admixture effects were summarized in the paper.

• The Journal of Korean Physical Therapy
• /
• v.25 no.2
• /
• pp.71-75
• /
• 2013

Purpose: Although use of a tilt table is recommended in clinical practice, there are no published guidelines regarding pressure and inclination for tilt table use. The aim of the current study was to assess the changes of pressure on sacrum and buttock according to different inclination of the tilt table in healthy subjects. Methods: Thirty two healthy subjects participated in this study. Subjects were positioned supine on the tilt table and safety straps were secured across the chest, pelvic, and knee with sufficient tension to prevent the subjects from falling. Pressure and peak pressure of sacrum and buttock were measured using pressure mapping system with the tilt table standing at $0^{\circ}$, $15^{\circ}$, $30^{\circ}$, $45^{\circ}$, $60^{\circ}$, $75^{\circ}$, and $85^{\circ}$ inclination. Results: A significant decrease in the pressure of sacrum and buttock was achieved by increasing tilt table inclination (p<0.05): $0^{\circ}{\sim}15^{\circ}$ (8.16%), $15^{\circ}{\sim}30^{\circ}$ (8.02%), $30^{\circ}{\sim}45^{\circ}$ (11.61%), $45^{\circ}{\sim}60^{\circ}$ (16.18%), $60^{\circ}{\sim}75^{\circ}$ (16%), and $75^{\circ}{\sim}85^{\circ}$ (11.48%). A significant decrease in the peak pressure was achieved by increasing tilt table inclination (p<0.05): $30^{\circ}{\sim}45^{\circ}$ (9.91%), $45^{\circ}{\sim}60^{\circ}$ (19.24%), $60^{\circ}{\sim}75^{\circ}$ (19.93%), and $75^{\circ}{\sim}85^{\circ}$ (11.48%). No significant peak pressure change was observed in $0^{\circ}{\sim}15^{\circ}$, $15^{\circ}{\sim}30^{\circ}$ tilt table inclination (p>0.05). Conclusion: The results of this study showed that the pressure of sacrum and buttock were decreased according to increasing tilt table inclination in healthy subjects. Guidelines are needed in order to optimize patient safety and overall outcome for tilt table standing.

• Journal of the Korean Society of Safety
• /
• v.28 no.1
• /
• pp.88-94
• /
• 2013

The purpose of this study is to find out the difference of foot pressure according to the firefighter's work postures for providing the basic information to prevent Musculoskeletal disorders. This study was conducted by 9 male firefighters. Work postures were selected for rescuee handling, fire hose and hydraulic rescue equipment work postures. These were divided into 3 position, "High", "Middle" and the postures of taking out and letting down hydraulic rescue equipment were analyzed as starting point and end point respectively. Foot Pressure was used to analyze contact area, peak pressure, and maximum force in terms of work postures, and compared between fire hose and hydraulic rescue equipment work postures. The results of foot pressure are as follows. According to the results of rescuee handling work postures, one person handling posture showed wide contact area and foot pressure showed the highest at right foot. Accoridng to the (High), (Middle), (Low) postures of fire hose, the results didn't show the difference among the contact area, peak pressure and maximum force. As the results of hydraulic rescue equipment work postures, (Low) postures showed the highest in terms of the right foot of contact area, peak pressure and maximum force and (High) postures showed the highest in left foot. The increase of foot pressure lead to be inconvenience of low extremity and muscle fatigue for maintaining postural control cause pain. Thus, it is necessary to design insole-equipped working shoe for reduce the impulse and effect of foot during the rescuee handling work which standing out as foot pressure.

• Journal of Korean Tunnelling and Underground Space Association
• /
• v.6 no.1
• /
• pp.41-50
• /
• 2004

The numerical investigation for the effects of blasting-induced vibration on adjacent dam and pore water pressure fluctuation was conducted through solid-water coupled analysis under dynamic loading. The stability of dam was examined by peak particle velocity of core. Pore water pressure distributions were calculated by steady state flow analysis using coupled analysis on ground water and blasting-induced vibration. The influence of pore water pressure and the effective stress distribution in the ground were also investigated. Furthermore, effective stress alteration was examined by applying Finn & Byrne Model to monitor the generation and dissipation of pore water pressure.

• Korean Journal of Applied Biomechanics
• /
• v.17 no.1
• /
• pp.135-144
• /
• 2007

The purpose of this study was to identify the effect of the subtalar sling ankle taping, by measuring changes in peak plantar pressure and subtalar angle during jump landing and walking in healthy subjects with subtalar sling ankle taping applied of the ankle joint. Fifty healthy subjects(8 males and 7 female, aged 22 to 25) were randomly divided into a participated in this study. They were free of musculoskeletal injury and neurologic deficit in lower extremity. The subjects were asked to perform 5M walking and single leg jump landing by under the guidance of physical therapists. Subtalar motions were typically measured as the angle made between the posterior aspect of the calcaneous and the posterior aspect of the lower leg during walking with taping or not. This measurement were made using a video system (30Hz sampling rate, rectified 60 Hz sampling rate). At the same time, peak lateral and vertical pressure were investigated using pressure distribution platforms(MatScan system) under foot during walking and single leg jump landing with taping or not. Statistical analysis was done by paired t-test and intraclass correlation coefficient [ICC(3.1)], using software SPSS. We have recently demonstrated significantly altered patterns of subtalr joint and peak plantar pressure when applied subtalar sling ankle taping(p<.05). Inversion angle of subtalar joint significantly decreased with taping(p<.05). The result suggest that pressure patterns observed in subjects are likely to result due to significant decrease in stress on ankle joint structures during jump landing and walking. Also, the result that the subtalar sling ankle taping procedure provides greater restiction of motion associated with ankle inversion. However, this study involved asymptomatic subjects without history of ankle inversion injury, further research is needed to assess the motion restraining effect of the subtalar sling ankle taping in subjects with lateral ankle instability.

• Journal of Biosystems Engineering
• /
• v.26 no.2
• /
• pp.123-130
• /
• 2001

The research described in this paper was aimed toward improving the understanding of the interaction of tire inflation pressure and the soil-tire interface stresses. A three-directional stress transducer was developed to measure stress distribution on undertread for a tractor tire. The transducer can directly measure three-directional stresses (normal stress, tangental stress and lateral stress and lateral stress) simultaneously and has both strong structure and high sensitivity, which is not changed by the abrasion of the detecting plate. Measurements of soil-undertread interface stresses were made at tire center on undertread on a 12.4-R24 radial tractor tire opeated at three combinations of a dynamic load (11.8kN) and three inflation pressures (59kPa, 108kPa and 157kPa). These measurements showed that as inflation pressure increased, the soil-undertread interface stresses increased. The results of three stresses comparisons were shown that the peak normal stresses were considerably higher than the tangential peak stresses and the peak lateral stresses.