• Nuclear Engineering and Technology
• /
• v.14 no.4
• /
• pp.186-195
• /
• 1982

The steam line break accident for Kori Unit 1 is analyzed by a code SYSRAN which calculates nuclear power and heat flux using the point kinetics equation and the lumped-parameter model and calculates system transient using the mass and energy balance equation with the assumption of uniform reactor coolant system pressure. The 1.4 f $t^2$ steam line break accident is analyzed at EOL (End of Life), hot shutdown condition in which case the accident would be most severe. The steam discharge rate is assumed to follow the Moody critical flow model. The results reveal the peak heat flux of 38% of nominal full power value at 60 second after the accident initiates, which is higher than the FSAR result of 26%. Trends for the transient are in good agreement with FSAR results. A sensitivity study shows that this accident is most sensitive to the moderator density coefficient and the lower plenum mixing factor. The DNBR calculation under the assumption of $F_{{\Delta}H}$=3.66, which is used in the FSAR with all the control and the shutdown assemblies inserted except one B bank assembly and of Fz=1.55 shows that minimum DNBR reaches 1.62 at 60 second, indicating that the fuel failure is not anticipated to occur. The point kinetics equation, the lumped-parameter model and the system transient model which uses the mass and energy balance equation are verified to be effective to follow the system transient phenomena of the nuclear power plants.lear power plants.

• Journal of Korea Water Resources Association
• /
• v.47 no.6
• /
• pp.561-572
• /
• 2014

The backwater effect at a tributary junction increases the risk of flood damage such as inundation and levee overflow. In particular, the rapid increase in water level may cause injury to persons. The purpose of this research is the development of the real-time flood forecasting technique as a part of the non-structural flood damage reduction measures. To this end, the factors causing a water level rising at a junction were examined, and the empirical formula for predicting flood level at a junction was developed using the calculated discharge and water level data from the well-constructed hydraulic model. The water level predictions show that average absolute error is about 0.2~0.3m with the maximum error of 1.0m and peak time can be captured prior to 0~5 hr. From the results of this study, the real-time flood forecasting system of a tributary junction can be easily constructed, and this system is expected to be utilized for reduction of flood inundation damage.

• Korean Journal of Fisheries and Aquatic Sciences
• /
• v.34 no.3
• /
• pp.199-206
• /
• 2001

Behavior of nutrients along the salinity gradients in the Seomjin River estuary was investigated in March July, September and November, 1999. Sampling sites were set based on the surface salinity during each cruise rather than geographic locations. The results suggest that source of nitrate and silicate was the Seomjin River discharge, while that of nitrite and phosphate was waste disposal from the Gwangynng Bay near the mouth of Seomjin River estuary. Ammonia was supplied inside the estuary at the region about $6\~8$ km far from Nancho Island. Strong removal behavior of some nutrient such as ammonia, phosphate and silicate was observed at $5\~15$ psu salinity area in November, where high concentrations of $chlorophyll\;a\;(>8{\mu}g/L$) occurred. High N : P ratios and entirely removal of phosphate at chlorophyll a peak region suggest that phosphate is the limiting factor for phytoplankton growth. Relatively high ratios of Rb to Ra (Rb: Fluorescence before acidification, Ra: Fluorescence after acidification) at $5\~15$ psu salinity region in November indicate that phytoplankton were in good physiological condition.

• Journal of Korea Water Resources Association
• /
• v.47 no.9
• /
• pp.767-776
• /
• 2014

Changes in climate have largely increased concentrated heavy rainfall, which in turn is causing enormous damages to humans and properties. Floods are one of the most deadly and damaging natural disasters known to mankind. The flood forecasting and warning system concentrates on reducing injuries, deaths, and property damage caused by floods. Therefore, the exact relationship and the spatial variability analysis of hydrometeorological elements and characteristic factors is critical elements to reduce the uncertainty in rainfall-runoff model. In this study, grid resolution depending on the topographic factor in rainfall-runoff models presents how to respond. semi-distribution of rainfall-runoff model using the model GRM simulated and calibrated rainfall-runoff in the Gamcheon and Naeseongcheon watershed. To run the GRM model, input grid data used rainfall (two event), DEM, landuse and soil. This study selected cell size of 500 m(basic), 1 km, 2 km, 5 km, 10 km and 12 km. According to the resolution of each grid, in order to compare simulation results, the runoff hydrograph has been made and the runoff has also been simulated. As a result, runoff volume and peak discharge which simulated cell size of DEM 500 m~12 km were continuously reduced. that results showed decrease tendency. However, input grid data except for DEM have not contributed increase or decrease runoff tendency. These results showed that the more increased cell size of DEM make the more decreased slope value because of the increased horizontal distance.

• Journal of Korea Water Resources Association
• /
• v.36 no.4
• /
• pp.533-545
• /
• 2003

This study analyzed several storm events observed in the Seolma-chun basin to derive the characteristic velocity of GIUH (Geomophological Instantaneous Unit Hydrograph) as well as its variability. Especially, this study focused on the variation of characteristic velocity due to the change of rainfall characteristics. The IUH of the Seolma-chun basin was derived using the HEC-1, whose peak discharge and time were then compared with those of the GIUH to derive the characteristic velocities. The characteristics velocities were analyzed by comparing with the GcIUH (Geomorphoclimatic IUH) as well as the characteristics of rainfall. Results are summarized as follows. (1) The characteristic velocity of GIUH was estimated higher with higher variability than the GcIUH, but their trends were found similar (2) Total amount of effective rainfall (or, mean effective rainfall) well explains the characteristic velocity of GIUH. This could be assured by the regression analysis, whose coefficient of determination was estimated about 0.6. (3) The duration and the maximum intensity of rainfall were found not to affect significantly on the characteristic velocity of GIUH. The coefficients of determination were estimated less than 0.3 for all cases considered. (4) For the rainfall events used in this study, the characteristic velocities of GIUH were found to follow the Gaussian distribution with its mean and the standard deviation 0.402 m/s and 0.173 m/s, respectively. Most of the values are within the range of 0.4∼0.5 m/s, and its coefficient of variation was estimated to be 0.43, much less than that of the runoff itself (about 1.0).

• Journal of Korea Water Resources Association
• /
• v.48 no.2
• /
• pp.115-126
• /
• 2015

In recent years, debris flow disaster has occurred in multiple locations between high and low mountainous areas simultaneously with a flooding disaster in urban areas caused by heavy and torrential rainfall due to the changing global climate and environment. As a result, these disasters frequently lead to large-scale destruction of infrastructures or individual properties and cause psychological harm or human death. In order to mitigate these disasters more effectively, it is necessary to investigate what causes the damage with an integrated model of both disasters at once. The objectives of this study are to analyze the mechanism of debris flow for real basin, to determine the PMP and run-off discharge due to the DAD analysis, and to estimate the influence range of debris flow for fan area according to the scenario. To analyse the characteristics of debris flow at the real basin, the parameters such as the deposition pattern, deposit thickness, approaching velocity, occurrence of sediment volume and travel length are estimated from DAD analysis. As a results, the peak time precipitation is estimated by 135 mm/hr as torrential rainfall and maximum total amount of rainfall is estimated by 544 mm as typhoon related rainfall.

• Nuclear Engineering and Technology
• /
• v.50 no.3
• /
• pp.356-367
• /
• 2018

A series of tests dedicated to station blackout (SBO) accident scenarios have been recently performed at the $Prim{\ddot{a}}rkreislauf-Versuchsanlage$ (primary coolant loop test facility; PKL) facility in the framework of the OECD/NEA PKL-3 project. These investigations address current safety issues related to beyond design basis accident transients with significant core heat up. This work presents a detailed analysis using the best estimate thermal-hydraulic code TRACE (v5.0 Patch4) of different SBO scenarios conducted at the PKL facility; failures of high- and low-pressure safety injection systems together with steam generator (SG) feedwater supply are considered, thus calling for adequate accident management actions and timely implementation of alternative emergency cooling procedures to prevent core meltdown. The presented analysis evaluates the capability of the applied TRACE model of the PKL facility to correctly capture the sequences of events in the different SBO scenarios, namely the SBO tests H2.1, H2.2 run 1 and H2.2 run 2, including symmetric or asymmetric secondary side depressurization, primary side depressurization, accumulator (ACC) injection in the cold legs and secondary side feeding with mobile pump and/or primary side emergency core coolant injection from the fuel pool cooling pump. This study is focused specifically on the prediction of the core exit temperature, which drives the execution of the most relevant accident management actions. This work presents, in particular, the key improvements made to the TRACE model that helped to improve the code predictions, including the modeling of dynamical heat losses, the nodalization of SGs' heat exchanger tubes and the ACCs. Another relevant aspect of this work is to evaluate how well the model simulations of the three different scenarios qualitatively and quantitatively capture the trends and results exhibited by the actual experiments. For instance, how the number of SGs considered for secondary side depressurization affects the heat transfer from primary side; how the discharge capacity of the pressurizer relief valve affects the dynamics of the transient; how ACC initial pressure and nitrogen release affect the grace time between ACC injection and subsequent core heat up; and how well the alternative feeding modes of the secondary and/or primary side with mobile injection pumps affect core quenching and ensure stable long-term core cooling under controlled boiling conditions.

• Journal of Korea Water Resources Association
• /
• v.35 no.3
• /
• pp.321-330
• /
• 2002

This study aims at the analysis of the geomorphological instantaneous unit hydrograph model (GIS-GIUH) with geographic information system for the rainfall-runoff analysis of watershed which is ungaged or doesn't have sufficient hydrologic data. The rainfall-runoff analysis was performed in Wi stream(Dongkok, Koro, Miseung, Byeungchun, Hyoreung, Museung) which is a representative experimental river basin of IHP. In the process of analysis of the GIUH model, developed GIS-GIUH model and Rosso-GIUH model were applied the study basin and computed hydrographs by these models were compared with observed hydrograph. The GiS-GIUH model shows more closely to the observed hydrograph than Rosso-GIUH model in the peak discharge of the hydrograph. For the development of the GIS-GIUH model, Gamma function factor N was given by N=3.25( $R_{B}$/ $R_{A}$)$^{0.126}$ $R_{L}$$^{-0.055}$, which is the relation of the watershed geomorphological factor, K was also obtained as K=1.50( $R_{A}$/( $R_{B}$. $R_{L}$))/$^{0.10}$.(( $L_{{\Omega}}$+ $L_{{\Omega}-1}$)/V)$^{0.37}$. As the results of analysis, it was found that GIS-GIUH model can be applied to an ungaged watersheds.eds.

• Water for future
• /
• v.29 no.4
• /
• pp.209-221
• /
• 1996

It may be difficult to make exact estimates of peak discharge or runoff depth of a flood and to establish the proper measurement for the flood protection since water stages or discharges have been rarely measured at small river basins in Korea. Three small catchments in the Su-Young river basin in Pusan were selected for the study areas. Various runoff parameters for the study areas were determined, and runoff analyses were performed using three different runoff models available in literatures; the storage function method, the discrete, linear, input-output model, and the linear reservoir model. The hydrographs calculated by three different methods showed good agreement with the observed flood hydrographs, indicating that the models selected are all capable of sucessfully modeling the flood events for small watersheds. The storage function method gave the best results in spite of its weakness that it could not be applicable to small floods, while the linear reservoir model was found to provide relatively good results with less parameters. The capabilities of simulating flood hydrographs were also evaluated based on the effective rainfall from the storage function parameters, the $\Phi$-index method, and the constant percentage method. For the On-Cheon stream watershed, the storage function parameters provided better estimates of effective rainfall for regenerating flood hydrographs than any others considered in the study. The $\Phi$-index method, however, resulted in better estimates of effective rainfall for the other two study areas.

• Proceedings of the Korea Water Resources Association Conference
• /
• 2019.05a
• /
• pp.75-75
• /
• 2019

첨두홍수량 자료는 홍수예경보 및 치수계획수립 등 하천관리에 있어서 매우 중요한 요소이다. 그러나 대규모 홍수가 발생 시 악천후가 동반된 기상상황이나, 현장 접근이 어려운 환경적 조건과 예산 및 인력 부족 등에 의한 불가피한 문제로 첨두홍수량을 측정하는데 어려움 있다. 따라서 일반적으로 수위-유량관계곡선식을 이용하여 첨두홍수량을 산정하지만 단순 고수위 외삽 추정을 통해 개발된 곡선식을 이용한 첨두홍수량 산정에 있어서는 주의가 필요하다. 이러한 경우 홍수가 지나간 후 현장조사를 통해 획득한 위치, 표고, 횡단면적 등 홍수흔적(flood marks)을 가지고 경사면적법(slope-area method)과 같은 간접적인 방법으로 첨두홍수량을 추정할 수 있다. 본 연구에서는 2018년 큰 호우사상이 발생한 내성천의 지류인 서천의 영주시(월호교) 지점과 남강의 산청군(하촌리) 지점에서 홍수흔적 조사를 통해 지점별 두 개의 단면을 선정하였다. 영주시(월호교) 지점의 두 단면 간 거리는 약 90m, 높이차는 약 0.21m로 조사되었고, 산청군(하촌리) 지점의 두 단면 간 거리는 약 330m, 높이차는 약 0.47m로 조사되었다. 경사면적법을 이용한 첨두 홍수량 추정에 적용된 조도계수는 '서천 하천기본계획(2014)', '남강 하천기본계획(2013)'에서 계획 홍수량 산정에 적용된 조도계수 0.029와 0.025를 적용하였다. 영주시(월호교) 지점은 2018년 9월 4일 발생한 호우사상의 첨두수위 5.59m에서 수위-유량관계곡선식을 이용하여 산정된 유량은 $1,127.8m^3/s$이고 경사면적법을 이용하여 추정된 유량은 $1,105.9m^3/s$로 약 -1.98%의 편차율이 발생하였다. 산청군(하촌리) 지점은 2018년 8월 26일 발생한 호우사상의 첨두수위 6.75m에서 수위-유량관계곡선식을 이용하여 산정된 유량은 $3,435.0m^3/s$이고 경사면적법을 이용하여 추정된 유량은 $3,233.3m^3/s$로 약 -6.24%의 편차율이 발생하였다. 경사면적법을 이용하여 추정된 첨두홍수량은 수위-유량관계곡선식을 이용하여 산정된 유량과 편차율이 지점별 ${\pm}10%$ 이내의 근사한 범위로 산정되었다. 따라서 경사면적법을 이용한 첨두홍수량 추정 방법의 적용에 있어서 적절한 것으로 판단된다.