• Journal of Biomedical Engineering Research
• /
• v.22 no.6
• /
• pp.511-518
• /
• 2001

In vitro corrosion resistance of the commercially used 76.5wt.%Pd-17.6%Cu-7.2%Ga and 77.3%Pd-6.0%Ga dental Prostheses high-Palladium system alloys in cast, degassing and porcelain-firing heat treatment conditions were evaluated by the potentiodynamic polarization technique in the de-aerated 0.9%NaCl and a modified Fusayama electrolyte. From the corrosion rate experimental results, we found that there is a small difference in the corrosion resistance depending on the microstructure. However. it was so small that there is no significant problem as a dental material. The 77.3%Pd-6.0%Ga showed better corrosion resistance than the 76.5%Pd-11.6%Cu-7.2%Ga dental Prostheses high-palladium system alloys. These experimental observations in 76.5%Pd-11.6%Cu-7.2%Ga alleys are mainly due to a rapid quenching and Cu in the alloy which accelerate the eutectic reaction with a segregation and Precipitates in the microstructure. On the ocher hand, 77.3%Pd-6.0%Ga alloys, which are solid-solution matrix, show much better col·lesion resistance compared with that of 76.5%Pd-11.6%Cu-7.2%Ga alloys.

• Journal of the Korean institute of surface engineering
• /
• v.50 no.2
• /
• pp.98-107
• /
• 2017

Pd-based membranes have been widely used in hydrogen purification and separation due to their high hydrogen diffusivity and infinite selectivity. However, it has been difficult to fabricate thin and dense Pd-based membranes on a porous stainless steel(PSS) support. In case of a conventional PSS support having the large size of surface pores, it was required to use complex surface treatment and thick Pd coating more than $6{\mu}m$ on the PSS was required in order to form pore free surface. In this study, we could fabricate thin and dense Pd membrane with only $3{\mu}m$ Pd layer on a new PSS support manufactured by metal injection molding(MIM). The PSS support had low surface roughness and mean pore size of $5{\mu}m$. Pd membrane were prepared by advanced Pd sputter deposition on the modified PSS support using fine polishing and YSZ vacuum filling surface treatment. At temperature $400^{\circ}C$ and transmembrane pressure difference of 1 bar, hydrogen flux and selectivity of $H_2/N_2$ were $11.22ml\;cm^{-2}min^{-1}$ and infinity, respectively. Comparing with $6{\mu}m$ Pd membrane, $3{\mu}m$ Pd membrane showed 2.5 times higher hydrogen flux which could be due to the decreased Pd layer thickness from $6{\mu}m$ to $3{\mu}m$ and an increased porosity. It was also found that pressure exponent was changed from 0.5 on $6{\mu}m$ Pd membrane to 0.8 on $3{\mu}m$ Pd membrane.

• Journal of the Institute of Convergence Signal Processing
• /
• v.10 no.4
• /
• pp.262-266
• /
• 2009

Since high speed and precision control shoud be satisfied in the position control system, the DC servo motor with easy control and satisfactory response characteristic is used. The various studies of position control techniques have been proposed in order to improve the control performance in the position control system. In this paper, the design method for a position control is suggested for constructing the PD controller in I-PD control system. The coefficients of PD controller in the I-PD control system are determined by using the transfer function which is normalized. Stability and root conditions of the system are derived from mathematical technique. From the result of computer simulation in I-PD control system by applying this control technique, is investigated by the method of proposed design the effectiveness of system response characteristic for input and disturbance.

• Journal of Magnetics
• /
• v.15 no.2
• /
• pp.45-50
• /
• 2010

We investigated the magnetism of vanadium monolayers on a Pd(001) surface. The electronic structure and the magnetic properties of the V/Pd(001) system were determined with the use of the full-potential linearized augmented plane-wave method within the general gradient approximation. Three magnetic configurations were studied: non-, ferro-, and antiferromagnetic. From the total energy calculations, we found that the V/Pd(001) system is the most stable in the antiferromagnetic configuration. The importance of relaxation on the magnetic properties of the systems was also studied. It was found that the Pd(001) surface covered with a V monolayer undergoes considerable relaxation in which the spacing between Pd layers increases in all three magnetic configurations. Contrary to the Pd interlayer spacing, the distance between the V overlayer and the topmost Pd layer is reduced. The interlayer spacing between the V overlayer and the Pd surface layer is the largest for the antiferromagnetic configuration. In the relaxed antiferromagnetic structure, the magnitude of the calculated magnetic moments on the V atoms was $1.31\;{\mu}_B$. The presence of the vanadium monolayer does not affect the paramagnetic properties of the Pd(001) surface.

• Korean Journal of Biological Psychiatry
• /
• v.16 no.1
• /
• pp.46-52
• /
• 2009

Objectives : The goal of this study was to compare the clinical characteristics of panic disorder respiratory subtype(PD-R) and non-respiratory subtype(PD-NR). Methods : 84 patients with panic disorder were enrolled and divided into 2 groups, 29 PD-R and 55 PD-NR. Diagnosis of panic disorder was evaluated using Diagnostic and Statistical Manual of Mental Disorders $4^{th}$ edition and Mini International Neuropsychiatric Interview. They were also measured with Hamilton Rating Scale for Anxiety(HAM-A), Hamilton Rating Scale for Depression(HAM-D), and Panic Disorder Severity Scale (PDSS). Results : PD-R group showed significantly higher scores in PDSS than those of PD-NR group(p=.027). After controlling for the severity of panic disorder and gender, PD-R group showed higher HAM-D and somatic anxiety subscale of HAM-A than those of PD-NR group. Furthermore, results of logistic regression analysis suggested that the somatic anxiety was a possible risk factor of PD-R(OR=1.404,p=0.009). Conclusion : These results suggest that somatic anxiety and depressive symptom would be important clinical characteristics of PD-R.

• Journal of Biomedical Engineering Research
• /
• v.20 no.6
• /
• pp.539-546
• /
• 1999

현재 상용화되고 있는 치과용 76.5% Pd-11.2% Cu-7.2% GarP 합금의 왁스모형을 원심주조기로 주조하여, 임상조건의 탈개스 및 세라믹 소성처리를 하였다. 이에따른 각각의 시편에 대해 미세조직의 변화를 주사전자현미경 및 EDS로 관찰하고, 최종적인 투과전자현미경으로 조사하였다. 각 조건의 편석, 결정립계 및 석출물부위를 주사전자현미경과 EDS 고 관찰한 결과, 이원계 Pd-GA합금의 안정상들에 해당하는 정량적인 조성비는, 단지 상대적으로 Ga의 성분비만 높게 감지되었다. 특히, 세라믹소성 처리후 미세조직에서 형성된 석출물에 근접한 기지조직일수록 Ga의 농도가 상대적으로 줄어든 고갈현상을 확인하엿다. 또한 투과전자현미경의 제한시야회절도형 분석결과, 주조 및 탈개스처리 후 미세조직의 편석부위에서는 GA의 가장 큰 강도를 보였고, 또 Ga과 Pd 고용체 사이에 미세한 판상의 석출물에 기인하는 줄무늬를 관찰하였다. 한편, 세라믹소성처리후 미세조직의 석출물은 금속간화합물 Pd2Ga으로 밝혀졌으며, 기지조직은 <100> 방향을 따라 약 25nm의 폭을 가지는 미세한 섬유상 형태의 소위 "tweed 조직'을 형성하였다.성하였다.

• Transactions of the Korean hydrogen and new energy society
• /
• v.12 no.3
• /
• pp.231-238
• /
• 2001

Electrocatalytic activity of palladium for hydrogen oxidation and reduction was studied using AC impedance method. The system under study was arranged in electrolytic mode consisting of Pd electrode under study, Pt counter electrode and Nafion electrolyte between them. Two types of Pd electrodes were used - carbon-supported Pd (Pd/C) and Pd foil electrode. Pd/C anode contacting pure hydrogen showed a steady decrease of charge transfer resistance with the increase of anodic overpotential, which is an opposite trend to that found with Pd foil anode. But Pd foil cathode also exhibited a decrease of the resistance with the increase of cathodic overpotential. The relationship between imposition of overpotential and subsequent change of the charge transfer resistance is determined by the ratio of the rate of faradaic process to the rate of mass transportation; if mass transfer limitation holds, increase of overpotential accompanies the increase of charge transfer resistance. Regardless of the physical type of Pd electrode, the anode contacting hydrogen/oxygen gas mixture did not reveal any independent arc originated from local anodic oxygen reduction.

• Journal of Navigation and Port Research
• /
• v.34 no.2
• /
• pp.117-122
• /
• 2010

Since fuzzy controllers are nonlinear, it is more difficult to set the controller gains and to analyse the stability compared to conventional PID controllers. This paper proposes a fuzzy PD+I controller for tracking control which uses a linear fuzzy inference(product-sum-gravity) method based on a conventional linear PID controller. In this scheme the fuzzy PD+I controller works similar to the control performance as the linear PD plus I(PD+I) controller. Thus it is possible to analyse and design an fuzzy PD+I controller for given systems based on a linear fuzzy PD controller. The scaling factors tuning scheme, another topic of fuzzy controller design procedure, is also introduced in order to fine performance of the fuzzy PD+I controller. The scaling factors are adjusted by a real-coded genetic algorithm(RCGA) in off-line. The simulation results show the effectiveness of the proposed fuzzy PD+I controller for tracking control problems by comparing with the conventional PID controllers.

• Journal of the Korean institute of surface engineering
• /
• v.39 no.6
• /
• pp.255-262
• /
• 2006

Pd-Cu alloy membrane for hydrogen separation was fabricated by sputtering and Cu reflow process. At first, the Pd and Cu was continuously deposited by sputtering method on oxidized Si support, the Cu reflow process was followed. Microstructure of the surface and permeability of the membrane was investigated depending on various reflow temperature, time, Pd/cu composition and supports. With respect to our result, Pd-Cu thin film (90 wt.% Pd/10 wt.% Cu) deposited by sputtering process with thickness of $2{\mu}m$ was heat-treated for Cu reflow The voids of the membrane surface were completely filled and the dense crystal surface was formed by Cu reflow behavior at $700^{\circ}C$ for 1 hour. Cu reflow process, which is adopted for our work, could be applied to fabrication of dense Pd-alloy membrane for hydrogen separation regardless of supports. Ceramic or metal support could be easily used for the membrane fabricated by reflow process. The Cu reflow process must result in void-free surface and dense crystalline of Pd-alloy membrane, which is responsible for improved selectivity oi the membrane.

• Journal of the Korean Magnetics Society
• /
• v.16 no.6
• /
• pp.271-275
• /
• 2006

We investigated the magnetoresistance of perpendicularly magnetized magnetic tunnel junction composed of Co/Pd multilayers. The magnetoresistance was maximized with Co electrodes of about 5 nm thickness, which evidenced the important role of the interface in tunneling process. Both the change in perpendicular magnetic anisotropy and improvement of junction resistance were observed with changing Co sublayers, while the spin scattering became dominant with increasing Pd sublayers.