• Aerospace Engineering and Technology
• /
• v.1 no.1
• /
• pp.117-127
• /
• 2002

In this paper, structure design of the payload section of the KSR-III was performed. The payload section of the KSR-III, which corresponds to the second stage, consists of the Scientific Payload Section for the mission of the rocket, the Payload Section (Electronics) for the communication between the rocket and the ground station, and the Payload Section (Attitude Control) for the attitude control of the rocket. In order to accomplish the mission, every payload and component should operate successfully during the mission period and the structure must satisfy the requirements of the payloads. In this research, precise composition of the payload section and payloads arrangement of the KSR-III were performed. And the modification of the structure to meet the requirements were described.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2005.05a
• /
• pp.717-720
• /
• 2005

Acoustic loads generated by a rocket propulsion system cause severe random vibrations on payloads. In developing a new launch vehicle, a random vibration level must be specified before the detailed design of payloads or electronic equipments. This paper deals with prediction procedures of a random vibration level on payload section of KSLV-I. The prediction is based on statistical energy analysis. In order to verify the prediction methodology, test and analysis on a sub-scale payload section are performed. The predicted results subject to very high level of acoustic loads show a good agreement with the test results performed in the high intensity acoustic chamber. The predicted random vibration level on payload section of KSLV-I is also presented in this paper.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2006.05a
• /
• pp.258-261
• /
• 2006

The structure of small launch vehicle can be divided into engine section and payload section. This paper introduces modal test of the payload section of small launch vehicle which is composed to satellite, PLA (Payload Adapter), VEB (Vehicle Equipment Bay), KMS (Kick Motor Support) and KM (Kick Motor). From this test, dynamic properties of the 2nd stage structure of small launch vehicle can be obtained. In this test, to simulate free-free boundary condition, test object was hung by 4 bungee cords and excited by using impact hammer Modal test data are analyzed by using TDAS(Test Data Analysis Software). As the result, modal parameters and mode shapes below 100Hz of the 2nd stage of small launch vehicle were identified.

• 제어로봇시스템학회:학술대회논문집
• /
• 1994.10a
• /
• pp.229-231
• /
• 1994

For the effective use of satellite communication transponder, tests for the payload system such as IOT(In-Orbit Test), RPM(Routine Payload Monitoring), CSM(Communicatios System Monitoring), and REV(Remote Earth-Station Verification) have to be conducted. Those tests are used in order to verify the condition and generic design of the satellite, to provide a database for operational calculations, and to maintain the quality of communication services. As the satellite communication system gets with wider expansion with higher complexity of operation, tests for the communication system also need more complex operation that usesophisticated computer-controlled measuring system. For and C language based measurement functions, which uses GPIB protocol and SCPI commands. But SICL requires knowledge of BASIC and C language as well as GPIB and SCPL system. This paper introduces a new language called CALSTEP-Control and Access Language for the Systems of Test Equipment and Payload. This language is designed for the operator to perform the tests for the satellite communication system without any special knowledge that is mentioned above. This language has very limited number of commands which are to be used to control the payload system and test equipments to perform IOT and CSM, and those commands are very readable and easy to understand, so an operator without any knowledge of BASIC and C programming language, or SICL and SCPI command can use it.

• ETRI Journal
• /
• v.46 no.2
• /
• pp.323-332
• /
• 2024

Receiver and transmitter monolithic microwave integrated circuit (MMIC) multifunction chips (MFCs) for active phased-array antennas for Ka-band satellite communication (SATCOM) terminals have been designed and fabricated using a 0.15-㎛ GaAs pseudomorphic high-electron mobility transistor (pHEMT) process. The MFCs consist of four-channel radio frequency (RF) paths and a 4:1 combiner. Each channel provides several functions such as signal amplification, 6-bit phase shifting, and 5-bit attenuation with a 44-bit serial-to-parallel converter (SPC). RF pads are implemented on the bottom side of the chip to remove the parasitic inductance induced by wire bonding. The area of the fabricated chips is 5.2 mm × 4.2 mm. The receiver chip exhibits a gain of 18 dB and a noise figure of 2.0 dB over a frequency range from 17 GHz to 21 GHz with a low direct current (DC) power of 0.36 W. The transmitter chip provides a gain of 20 dB and a 1-dB gain compression point (P1dB) of 18.4 dBm over a frequency range from 28 GHz to 31 GHz with a low DC power of 0.85 W. The P1dB can be increased to 20.6 dBm at a higher bias of +4.5 V.

• Advances in aircraft and spacecraft science
• /
• v.7 no.4
• /
• pp.371-385
• /
• 2020

A forward-facing aerospike attached to a payload fairing of a satellite launch vehicle significantly alters its flowfield and decreases the aerodynamic drag in transonic and low supersonic speeds. The present payload fairing is an axisymmetric configuration and consists of a blunt-nosed body along with a conical section, payload shroud, boat tail and followed by a booster. The main purpose of the present numerical simulations is to evaluate flowfield and assess the performance of aerodynamic drag coefficient with and without aerospike attached to a payload fairing of a typical satellite launch vehicle in freestream Mach number range 0.8 ≤ M_∞ ≤ 3.0 and freestream Reynolds number range 33.35 × 10⁶/m ≤ Re_∞ ≤ 46.75 × 10⁶/m whichincludes the maximum aerodynamic drag and maximum dynamic conditions during ascent flight trajectory of the satellite launch vehicle. A numerical simulation has been carried out to solve time-dependent compressible turbulent axisymmetric Reynolds-averaged Navier-Stokes equations. The closure of the system of equations is achieved using the Baldwin-Lomax turbulence model. The aerodynamic drag reduction mechanism is analysed employing numerical results such as velocity vector plots, density and Mach contours in conjunction with the experimental flow visualization pictures. The variations of wall pressure coefficient over the payload fairing with and without aerospike are exhibiting different kind of flowfield characteristics in the transonic and low supersonic speeds. The numerically computed results are compared with schlieren pictures, oil flow patterns and measured wall pressure distributions and exhibit good agreement between them.

• 제어로봇시스템학회:학술대회논문집
• /
• 1994.10a
• /
• pp.49-53
• /
• 1994

Advanced Real-Time Satellite Simulator(ARTSS) has been developed to support the telemetry, tracking and command operations of the ETRI satellite control system and to provide satellite engineers a more powerful and informative satellite simulations tool on the desktop. To provide extensive simulation functions for a communication satellite system in the pre-operational and operational missions, ARTSS uses a geosynchronous orbit(GEO) satellite model consisting of the attitude and orbit control subsystem, the power subsystem, the thermal subsystem, the telemetry, command and ranging subsystem, and the communications payload subsystem. In this paper, the system features and functions are presented and the satellite subsystem models are explained in detail.

• Advances in aircraft and spacecraft science
• /
• v.9 no.1
• /
• pp.1-15
• /
• 2022

This paper presents calibration of flush air data sensing systems during ascent period of a satellite launch vehicle. Aerodynamic results are numerically computed by solving three-dimensional time dependent compressible Euler equations over a payload shroud of a satellite launch vehicle. The flush air data system consists of four pressure ports flushed on a blunt-cone section of the payload shroud and connected to on board differential pressure transducers. The inverse algorithm uses calibration charts which are based on computed and measured data. A controlled random search method coupled with neural network technique is employed to estimate pitch and yaw angles from measured transient differential pressure history. The algorithm predicts the flow direction stepwise with the function of flight Mach numbers and can be termed as an online method. Flow direction of the launch vehicle is compared with the reconstructed trajectory data. The estimated values of the flow direction are in good agreement with them.

• 제어로봇시스템학회:학술대회논문집
• /
• 1994.10a
• /
• pp.218-223
• /
• 1994

On the satellite communication system, conventional key issues of control have been focused on the attitude and orbit control, monitoring and control of communication payload such as IOT(In-Orbit-Test) and CSM(Communication System Monitoring) and so on. As the vulnerabilities are being increased on the satellite communication network, security services are required to protect it against security violated attacks. In this paper, a security architecture for satellite communication network is presented in order to provide security services and mechanisms. Authentication protocol and encryption scheme are also proposed for spacecraft command authentication and confidentiality.

• The Transactions of the Korean Institute of Electrical Engineers
• /
• v.45 no.1
• /
• pp.123-130
• /
• 1996

Due to high payload capacity and high length-to -cross-section ratio requirements, long-reach manipulator systems are expected to exhibit significant structural flexibility. To avoid structural vibrations during operations, various types of input shaping filtering methods have been investigated. A robust notch filtering method and an impulse shaping filtering method were investigated and implemented. In addition, two very different approaches have been developed and compared. One new approach, referred to as a