• 분석과학
• /
• 제23권2호
• /
• pp.165-171
• /
• 2010

글루코스 옥시다아(GOx)제 고정화 바이오센서를 두 가지 방법으로 제조 하였다. 첫 번째 방법은 폴리(maleic anhydride) 그래프트 탄소나노튜브(PMAn-g-MWCNT) 전극에 감마선 조사법으로 제조 된 Au 나노입자를 물리적으로 흡착시킨 후, GOx을 고정화 시켜 바이오센서를 제조한 경우이고, 다른 하나는 PMAn-g-MWCNT 전극에서 Au 이온을 전기화학적으로 환원시켜 Au 나노입자를 코팅 시키고, 그 위에 GOx을 고정화 시켜 바이오센서를 제조 한 경우이두. 제조된 바이오센서에 대해 효율 평가를 수행 하였는데, 물리적 흡착법으로 제조된 전극의 경우 검출 범위는 $30\;{\mu}M\sim100\;{\mu}M$이었으며, 검출한계는 $15\;{\mu}M$이었다. 또한 ascorbic acid와 uric acid에 대한 검출한계는 7.6%이었다. 물리적으로 Au 나노입자가 흡착된 전극의 경우가 글루코스 측정에 매우 우수한 전극임을 확인 하였다.

• 한국진공학회:학술대회논문집
• /
• 한국진공학회 2014년도 제46회 동계 정기학술대회 초록집
• /
• pp.490.2-490.2
• /
• 2014

Since the general solar cells accept sun light at the front side, excluding the electrode area, electrons move from the emitter to the front electrode and start to collect at the grid edge. Thus the edge of gridline can be important for electrical properties of screen-printed silicon solar cells. In this study, the improvement of electrical properties in screen-printed crystalline silicon solar cells by contact treatment of grid edge was investigated. The samples with $60{\Omega}/{\square}$ and $70{\Omega}/{\square}$ emitter were prepared. After front side of samples was deposited by SiNx commercial Ag paste and Al paste were printed at front side and rear side respectively. Each sample was co-fired between $670^{\circ}C$ and $780^{\circ}C$ in the rapid thermal processing (RTP). After the firing process, the cells were dipped in 2.5% hydrofluoric acid (HF) at room temperature for various times under 60 seconds and then rinsed in deionized water. (This is called "contact treatment") After dipping in HF for a certain period, the samples from each firing condition were compared by measurement. Cell performances were measured by Suns-Voc, solar simulator, the transfer length method and a field emission scanning electron microscope. According to HF treatment, once the thin glass layer at the grid edge was etched, the current transport was changed from tunneling via Ag colloids in the glass layer to direct transport via Ag colloids between the Ag bulk and the emitter. Thus, the transfer length as well as the specific contact resistance decreased. For more details a model of the current path was proposed to explain the effect of HF treatment at the edge of the Ag grid. It is expected that HF treatment may help to improve the contact of high sheet-resistance emitter as well as the contact of a high specific contact resistance.

• 대한화학회지
• /
• 제35권5호
• /
• pp.545-552
• /
• 1991

수은 이온의 정량을 위해 l-sparteine으로 처리한 carbon paste 전극(CPE)을 제작하였다. 수용액중의 수은 이온을 CPE에 수식 시킨 l-sparteine과 반응시켜 착화합물 상태로 전극표면에 석출시킨 후 이 착물을 벗김 전압-전류곡선법을 사용하여 정량하였다. 또한 수식된 CPE의 전극반응을 순환 전압 전류 곡선법을 사용하여 초산/초산염 완충용액에서 조사하였다. 한번 사용한 전극은 산 용액으로 처리하여 5회 이상 재사용할 수 있었다. 선형주사 전압전류법을 사용하였을 경우 $2.0{\times}10^{-6}$ M 농도까지 정량이 가능하였다. 시차펄스 전압전류법으로 실험할 경우 $7.0 {\times}10^{-7}$ M 농도까지 직선적으로 감응함을 알 수 있었으며 그 때의 상대 표준편차는 ${\pm}$5.1% 이었다. 이 경우 검출 한계는 $5.O{\times} 10^{-7}$ M이었다. 리간드와 착물을 형성할 것으로 예상되는 여러 금속이온에 대한 방해 작용을 조사하였다. 그 결과 은(I) 이온이 방해를 하지만 염화칼륨으로 사전 처리하여 방해작용을 제거할 수 있었다.

• 마이크로전자및패키징학회지
• /
• 제10권4호
• /
• pp.47-52
• /
• 2003

PDP전극용 Ag전극 페이스트의 프릿으로 기존의 Pb-based 프릿을 대신 할 수 있는 Bi-based 조성의 새로운 유리조성의 가능성을 검토하였다. PDP디스플레이 응용을 위해 프릿의 저융점화 및 열팽창계수 제어를 행하였고, 이를 전극 페이스트 제조에 적용하여 스크린 프린팅된 전극을 평가하였다. $Bi_2O_3$를 50-60wt%이상 첨가된 $Bi_2O_3-B_2O_3-Al_2O_3$계 조성의 프릿은 연화점이 400∼$480^{\circ}C$, 열팽창계수가 7.31∼$10.02\times 10^{-6}/^{\circ}C$이며, 전극의 단자저항은 4.1∼4.8$\Omega$ 이었다. 본 연구에서 새로이 개발된 Bi계 프릿조성은 Pb계 조성의 프릿에 상당하는 물성을 얻을 수 있었으며, 이를 전극용 페이스트에 적용한 결과, 전극 프린팅에서 퍼짐성과 균일성이 우수하였다. PDP전극용 무연, 무 알카리 프릿으로 Bi계 조성의 적용가능성을 확인할 수 있었다.

• Carbon letters
• /
• 제26권
• /
• pp.18-24
• /
• 2018

Pollution of chloride ion-reinforced concrete can trigger active corrosion processes that reduce the useful life of structures. Multifunctional materials used as a counter-electrode by electrochemical techniques have been used to rehabilitate contaminated concrete. Cement-based pastes added to carbonaceous material, fibers or dust, have been used as an anode in the non-destructive Electrochemical Chloride Extraction (ECE) technique. We studied the performance of the addition of Carbon Fiber (CF) in a cement-graphite powder base paste used as an anode in ECE of concretes contaminated with chlorides from the preparation of the mixture. The experimental parameters were: 2.3% of free chlorides, 21 days of ECE application, a Carbon Fiber Volume Fraction (CFVF) of 0.1, 0.3, 0.6, 0.9%, a lithium borate alkaline electrolyte, a current density of $4.0A/m^2$ and a cement/graphite ratio of 1.0 for the paste. The efficiency of the ECE in the traditional technique using metal mesh as an anode was 77.6% and for CFVF of 0.9% it was 90.4%, with a tendency to increase to higher percentages of the CFVF in the conductive cement-graphite paste, keeping the pH stable and achieving a homogeneous ECE in the mass of the concrete contaminated with chlorides.

• Bulletin of the Korean Chemical Society
• /
• 제35권10호
• /
• pp.3025-3029
• /
• 2014

To realize copper-based electrode materials for printed electronics applications, it is necessary to improve the adhesion strength between conductive lines and the substrate. Here, we report the preparation of Cu pastes using (3-glycidoxypropyl) trimethoxysilane (GPTMS) prepolymer as an adhesion promoter (AP). The Cu pastes were screen-printed on glass and polyimide (PI) substrates and sintered at high temperatures (> $250^{\circ}C$) under a formic acid/$N_2$ environment. According to the adhesion strengths and electrical conductivities of the sintered Cu films, the optimized Cu paste was composed of 1.0 wt % GPTMS prepolymer, 83.6 wt % Cu powder and 15.4 wt % vehicle. After sintering at $400^{\circ}C$ on a glass substrate and $275^{\circ}C$ on a PI substrate, the Cu films showed the sheet resistances of $10.0m{\Omega}/sq$. and $5.2m{\Omega}/sq$., respectively. Furthermore, the sintered Cu films exhibit excellent adhesion properties according to the results of the ASTM-D3359 standard test.

• 융복합기술연구소 논문집
• /
• 제8권1호
• /
• pp.33-39
• /
• 2018

The screen printing method for forming the electrode by applying the existing pressure is difficult to apply to thin wafers, and since expensive Ag paste is used, it is difficult to solve the problem of cost reduction. This can solve both of the problems by forming the front electrode using a plating method applicable to a thin wafer. In this paper, the process conditions of electrode formation are optimized by using LIEP (Light-Induced Electrode Plating). Experiments were conducted by varying the Ni plating bath temperature $40{\sim}70^{\circ}C$, the applied current 5 ~ 15 mA, and the plating process time 5 ~ 20 min. As a result of the experiment, it was confirmed that the optimal condition of the structural characteristics was obtained at the plating bath temperature of $60^{\circ}C$, 15 mA, and the process time of 20 min. The Cu LIEP process conditions, experiments were conducted with Cu plating bath temperature $40{\sim}70^{\circ}C$, applied voltage 5 ~ 15 V, plating process time 2 ~ 15 min. As a result of the experiment, it was confirmed that the optimum conditions were obtained as a result of electrical and structural characteristics at the plating bath temperature of $60^{\circ}C$ and applied current of 15 V and process time of 15 min. In order to form Ni silicide, the firing process time was fixed to 2 min and the temperature was changed to $310^{\circ}C$, $330^{\circ}C$, $350^{\circ}C$, and post contact annealing was performed. As a result, the lowest contact resistance value of $2.76{\Omega}$ was obtained at the firing temperature of $310^{\circ}C$. The contact resistivity of $1.07m{\Omega}cm^2$ can be calculated from the conditionally optimized sample. With the plating method using Ni / Cu, the efficiency of the solar cell can be expected to increase due to the increase of the electric conductivity and the decrease of the resistance component in the production of the solar cell, and the application to the thin wafer can be expected.

• 한국전기전자재료학회논문지
• /
• 제29권8호
• /
• pp.461-465
• /
• 2016

n-type silicon shows the better tolerance towards metal impurities with a higher minority carrier lifetime compared to p-type silicon substrate. Due to better lifetime stability as compared to p-type during illumination made the photovoltaic community to switch toward n-type wafers for high efficiency silicon solar cells. We fabricated the front electrode of the n-type solar cell with AgAl paste. The electrodes characteristics of the AgAl paste depend on the contact junction depth that is closely related to the firing temperature. Metal contact depth with p+ emitter, with optimized depth is important as it influence the resistance. In this study, we optimize the firing condition for the effective formation of the metal depth by varying the firing condition. The firing was carried out at temperatures below $670^{\circ}C$ with low contact depth and high contact resistance. It was noted that the contact resistance was reduced with the increase of firing temperature. The contact resistance of $5.99m{\Omega}cm^2$ was shown for the optimum firing temperature of $865^{\circ}C$. Over $900^{\circ}C$, contact junction is bonded to the Si through the emitter, resulting the contact resistance to shunt. we obtained photovoltaic parameter such as fill factor of 76.68%, short-circuit current of $40.2mA/cm^2$, open-circuit voltage of 620 mV and convert efficiency of 19.11%.

• 한국전기전자재료학회논문지
• /
• 제26권12호
• /
• pp.878-881
• /
• 2013

In this study, we have fabricated the dye sensitized solar cell (DSSC) composed by a transparent conductive oxide (TCO), a nanocrystalline semiconductor film usually $TiO_2$, a sensitizer adsorbed on the surface of the semiconductor, an electrolyte containing a redox mediator and a counter electrode. The $TiO_2$ nanopowder was prepared by sol-gel methode. The HCl (hydrochloric acid) and TBAOH (Tetrabutyl amonium hydroxide) was added for improving the catalyst and distributed properties of $TiO_2$ nanopowder. Ammonium hydroixde was added in order to control the morphology and size of $TiO_2$ nano crystal. A $TiO_2$ paste for working electrode was prepared with the addition of HPC (hydroxypropyl cellulos) used as a binder of which volume was controled as 1.3, 1.5, 1.7, and 2.0%. The measured I-V curves of assembled DSSC showed that the cell with 1.7% HPC binder had the best efficiency of 6.79%.

• 한국전기전자재료학회논문지
• /
• 제19권10호
• /
• pp.966-970
• /
• 2006

We reported on characteristics of the piezoelectric ceramic-polymer composite for the application of the thick-film speaker. The PVDF-PZT composites were fabricated to incorporate the advantages of both ceramic and polymer with various mixing ratios by 3-roll mill mixer. The composite solutions were coated by the conventional screen-printing method on ITO electrode coated PET (Polyethylene terephthalate) polymer film. After depositing the top-electrode of silver-paste, 4 kV/mm of DC field was applied at $120^{\circ}C$ for 30 min to poling the composite films. The value of $d_{33}$ (piezoelectric charge constant) was increased when the PZT weight percent was increased. The maximum value of the $d_{33}$ was 24 pC/N at 70 wt% PZT. But the $g{33}$ (piezoelectric voltage constant) showed the maximum value of $32mV{\cdot}m/N$ at 65 wt% of PZT powder. The SPL (sound pressure level) of the speaker fabricated with the 65:35 composite film was about 68 dB at 1 kHz.