• The Journal of The Korea Institute of Intelligent Transport Systems
• /
• v.22 no.5
• /
• pp.108-126
• /
• 2023

In this paper, the dynamic hard shoulder running for bus only (HSRFBO) was presented to solve the traffic congestion by increase the capacity in chronic congested sections of highways, and a simulation was performed to evaluate the comparison with the current hard shoulder running for all vehicles(HSRFAV) and median bus only lane and HSR(MBOLHSR). According to the evaluation results, it was evaluated to be more advantageous in terms of traffic flow and safety than the current HSRFAV. In addition, the speed of passing buses is slightly reduced compared to the MBOHSR, but the speed of entering and exiting buses is increased and the speed of buses and cars is greatly improved. Therefore It was analyzed that the efficiency of transport personnel was also improved. In particular, it is expected that traffic flow will be stabilized as the difference in speed between passenger cars and buses will be greatly reduced, and violations of exclusive bus lanes by passenger cars will be greatly reduced. In addition, the operation time of HSR is greatly reduced, so that the original function of the shoulder lane can be maintained as much as possible. As a result, it was analyzed that the risk of accidents was significantly reduced when operating HSRFBO compared to when operating MBOHSR, and cross-conflicts with high accident severity did not occur.

• Journal of Korean Society for Atmospheric Environment
• /
• v.9 no.1
• /
• pp.69-77
• /
• 1993

Exhaust emissions are calculated as a product of the emission factor and the vehicle kilometer traveled(VKT). The emission factor is a function of several parameters such as vehicle model year, vehicle mileage, traffic conditions, etc. The representative driving cycles classified as ten different types of an average vehicle speed were selected by analyzing passenger car driving patterns in Seoul. 51 vehicles were sampled and analyzed by types of vehicles, fuels used, model years and vehicle mileages also, exhaust emissions of them were measured by chassis dynamometer. Regression equations between average vehicle speeds and exhaust emissions are made for the estimation of emission factors at different vehicle speeds. Annual emission rates of air pollutants from motor vehicles in Korea were 1116$\times10^3 ton, 149\times10^3 ton, 413\times10^3 ton and 67\times10^3$ ton for CO, HC, NOx and particulats, respetively in 1990. It was found that 56% of CO and 49% of HC were originated from passenger cars and taxis, in addition, 87% of NOx and 100% of particulates were from buses and trucks using diesel fuels.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.16 no.2
• /
• pp.106-113
• /
• 2008

The goal of crashworthiness is an optimized vehicle structure that can absorb the crash energy by controlled vehicle deformations while maintaining adequate space so that the residual crash energy can be managed by the restraint systems to minimize crash loads transfer to the vehicle occupants. Front side assembly is one of the most important energy absorbing components in relating to the crashworthiness design of vehicle. The structure and shape of the front side assemblies are different depending on auto-makers and size of vehicles. Thus, it is not easy to grab an insight on designer's intention when you glance at a new front side member without experiences. In this paper, we have performed the explicit nonlinear dynamic finite element analysis on the front side assembly of a passenger car to investigate the effect of thickness distribution of the front side assembly on the collapse shape, which is important in the aspect of controlling deformation to maintain adequate space, from the viewpoint of reverse engineering. To do this, we have performed crash FE analysis for the assembly by varying the thickness distribution of the assembly.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.24 no.3 s.174
• /
• pp.718-727
• /
• 2000

Nowadays, most passenger cars equipped with automatic transmissions use torque converter clutches to reduce fuel consumption, and recently the slip control scheme of torque converter clutches is widely studied for the expansion of the operating region of torque converter clutches and thus for the further improvement of the fuel economy of vehicles. In this study, the analysis of the torque converter clutch system including the line pressure control unit of the automatic transmission and the actuating hydraulic control unit of the torque converter clutch is performed, and a feedforward controller and a fuzzy logic controller for its slip control are proposed. Also, for the slip controller to use the grade resistance information during control, an observer-based grade resistance estimator is designed. The performance of the designed grade resistance estimator and the slip controller is verified by dynamic simulations, and the effect of the torque converter clutch slip control on the fuel economy is examined using a driving cycle simulation.

• Journal of Mechanical Science and Technology
• /
• v.14 no.4
• /
• pp.418-425
• /
• 2000

Recently, many passenger cars have adopted automatic transmissions for shifting gears, and thus the smooth and precise control of gear shifts of passenger car automatic transmissions has become more and more essential for the riding comfort of vehicles equipped with automatic transmissions. In this article, a neural network-based supervisor for an automotive shift controller considering the throttle opening, variations in throttle opening, and the driving load is presented. For using the driving load information, an observer-based driving load estimation algorithm is proposed. A proportional-integral-derivative controller along with an open loop controller is used as a low level controller for controlling the gear shifts, and a supervisory controller for properly adapting the shift control parameters of the low level shift controller is designed using ANFIS. To evaluate the control performance of the proposed supervisor-based shift controller, both simulation studies and experimental studies are performed for various shifting situations.

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.24 no.3
• /
• pp.253-260
• /
• 2014

conducted. In-situ measurements were conducted to investigate the noise characteristics in high-speed trains such as KTX and KTX-Sancheon. Binaural microphones and spherical microphone were adopted to record and evaluate the spectral characteristics and noise incidence characteristics at the seats in the passenger cars. Environmental elements were also recorded during the noise measurements using a camcorder and GPS application. In addition, auditory tests were conducted to investigate annoyance of interior noise of high-speed trains. Based on the objective measure and subjective responses on interior noise, statistical analysis such as correlation and regression analyses were carried out. From the results perception models for evaluating the interior noise of high-speed train were derived.

• Journal of ILASS-Korea
• /
• v.9 no.1
• /
• pp.8-14
• /
• 2004

future exhaust emission limits for diesel-driven passenger cars will force the automotive company to significantly develop of the new technologies of diesel engine respectively of the drive assemblies. As we know, the contributions of soot and nitrogen oxide is the main problems in diesel engine. Recently, as a result, the pilot injection of common-rail fuel injection system recognizes an alternative function to solve an environmental problem. This study describes the effect of the nozzle structure and driven characteristic of injector on pilot injection fur a passenger car common-rail system. The pilot spray structure such as spray tip penetration, spray speed and spray angle were obtained by high speed images, which is measured by the Mie scattering method with optical system fur high-speed temporal photography. Also the CFD analysis was carried out for fuel behavior under high pressure in between needle and nozzle of injector for common-rail system to know the condition of initial injection at experiment test. It was found that solenoid-driven injector with 5-hole was faster than 6-hole injector in spray speed at same conditions and piezo-driven injector showed faster response than solenoid injector.

• Transactions of Materials Processing
• /
• v.24 no.2
• /
• pp.130-137
• /
• 2015

This paper presents the development process of automotive side door impact beam for passenger cars. Weight reduction while maintaining functional requirements is one of the major goals in the automotive industry. In this study, thin-walled side door beam using quenchable boron steel was designed to reduce the weight of conventional side door tubular one. In order to estimate design for the proposed side door beams, the static side impact protection tests(FMVSS 214) were conducted using the finite element method. Based on the simulation results, geometry modification of the side door beam has been performed via creating new reinforcing ribs. Furthermore, the manufactured frontal impact beam was mounted on the real side door of a passenger car, and then static impact protection test carried out. It is concluded that the presented test results can provide significant contribution to the stiffness of side door impact beams and light-weighting door research.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.10 no.2
• /
• pp.166-173
• /
• 2002

The wheel bearing hub unit is developed type of wheel bearing unified with the hub parts. It has advantage of reducing the weight and the number of components. And, it also improves uniformity of manufacturing quality, In order to design the wheel bearing hub units, many techniques are used such as load analysis, structure analysis and bearing characteristics analysis and so forth. These techniques need highly accurate load conditions founded on service conditions. In this study, to design the wheel bearing hub units used widespread in passenger cars, the service load was measured through driving tests on the public roads and in the special events. The public roads are classified into highway, intercity road, rural road, urban road, and unpaved road so as to know what the characteristics of the road loads are. The results of the tests showed that the wheel force was relative to the lateral acceleration, and also could be calculated from the lateral acceleration. The lateral acceleration was measured from 0.0G to 0.6G in general driving on the public roads, with different distributions in each road type. In special events, the maximum lateral acceleration was measured from 0.8G to 1.3G.

• International Journal of Automotive Technology
• /
• v.7 no.2
• /
• pp.155-160
• /
• 2006

This paper presents a vehicle model for analyzing the transient shifting characterisitics of a passenger car with automatic transmission. Then the presented vehicle model was linked with the dynamic model of an automatic transmission. In order to identify the parameters of the vehicle model, we installed a test equipment with an accelerometer in a conventional vehicle and performed road tests. With the proposed vehicle model, we simulated the dynamic characteristics during shifting, and benchmarked with experimental results. Moreover, a modal analysis was carried out to investigate the effect of the vehicle model in the frequency domain and to obtain the transfer function of the vehicle model. In addition, we showed the numerical results in the time domain for analyzing the effect of each stiffness element, such as engine mountings and suspensions.