• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.29 no.12 s.243
• /
• pp.1335-1343
• /
• 2005

The calibration technique of Time Resolved Laser Induced Incandescence was investigated both experimentally and numerically by using standard-sized carbon black particles for the instantaneous soot measurement at exhaust tail pipe in engine. The carbon black particles (19nm, 25nm, 45nm and 58nm) used in this study are similar, though not identical, to soot particle generated from flame not only in morphology but also in micro-structure. The amount of soot loading in flow was controled by a diluted gas (nitrogen) and was measured by the gravimetric method at exhaust pipe in calibrator. The successful calibrations of primary particle size and soot mass fraction were carried out at the range from 19nm to 58nm and from $0.25mg/m^3$ to $37mg/m^3$ respectively. And based on these results the numerical simulation of LII signal was tuned and the effect of an exhaust temperature variation on the decay rate of LII signal was corrected.

• 한국전산유체공학회:학술대회논문집
• /
• 2004.03a
• /
• pp.106-112
• /
• 2004

A kinetic theory analysis is made of low-speed gas flows around a micro-plate. The Boltzmann equation simplified by a collision model is solved by means of a finite difference approximation with the discrete ordinate method. The method does not suffer from statistical noise which is common in particle based methods and requires much less amount of computational effort. Calculations are made for flows around a micro-scale flat plate with a finite length of 20 microns. The method is assessed by comparing the results with those from several different methods and available experimental data.

• Journal of computational fluids engineering
• /
• v.9 no.3
• /
• pp.1-7
• /
• 2004

A kinetic theory analysis is made of low-speed rarefied gas flows around a flat plate. The Boltzmann equation simplified by a collision model is solved by means of a finite difference approximation with the discrete ordinate method. The method does not suffer from statistical noise which is common in particle based methods and requires much less amount of computational effort. Calculations are made for flows around a micro-scale flat plate with a finite length of 20 microns. The method is assessed by comparing the results with those from several different methods and available experimental data.

• Proceedings of the Korean Society of Computer Information Conference
• /
• 2023.01a
• /
• pp.395-398
• /
• 2023

본 논문에서는 물리 기반 옷감 시뮬레이션과 SPH(Smoothed particle hydrodynamics) 기반의 유체 시뮬레이션 간의 상호작용에서 표현되는 다양한 물리적 효과를 GPU 기반으로 빠르게 표현할 수 있는 프레임워크를 제안한다. 기존 기법과는 다르게 수치적 안정성을 개선하기 위해 CCD(Continuous collision detection)를 활용하였으며, 모든 연산이 GPU에서 동작하기 때문에 매우 빠르게 옷감과 유체의 상호작용 장면인 다공성 재질, 기공 흐름, 흡수, 방사, 확산을 모델링할 수 있다.

• Proceedings of KOSOMES biannual meeting
• /
• 2009.06a
• /
• pp.89-94
• /
• 2009

This study aims to examine the the characteristics if the sea water circulation in related to the change of the water exchange rate according to the the development phases of Busan Port. To clarify the characteristics, the water exchange caused by construction if new-port and river discharge conditions was examined by the numerical experiments using the Lagrangian particle tracking model based on 2-D shallow water equation. This study deals with the charge of flow field and water exchange after redevelopment using numerical simulation technique, based on the field observation and 4 rivers discharge flow. As a result if numerical simulation, Variation if current velocity in Busan North Port is almost nothing before and after construction. Water exchange of channel in area of redevelopment is a little. Futhermore, the tidal exchange had a tendency to be small both before and after redevelopment by 60%.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.31 no.2
• /
• pp.1-9
• /
• 2003

In the present study, a 3-D Parallel DSMC method in developed on unstructured meshes for the efficient simulation of rarefied gas flows. Particle tracing between cells in achieved based on a linear shape function extended to three dimensions. For high parallel efficiency, successive domain decomposition is applied to achieve load balancing between processors by accounting for the number of particles. A particle weighting technique is also adopted to handle flows containing gases of significantly dirrerent number densities in the same flow domain. Application is made for flow past a 3-D delta wing and the result is compared with that from experiment and other calculation. Flow around a rocket payload at 100km altitude is also solved and the effect of plume back flow from the nozzle in studied.

• Nuclear Engineering and Technology
• /
• v.51 no.7
• /
• pp.1828-1834
• /
• 2019

The performance of a plastic scintillator for use in an in situ measurement system was analyzed using simulation and experimental methods. The experimental results of four major pure beta-emitting radionuclides, namely $^3H$, $^{14}C$, $^{32}P$, and $^{90}Sr/^{90}Y$, were compared with those obtained using a Monte Carlo N-particle (MCNP) code simulation. The MCNP simulation and experimental results demonstrated good agreement for $^{32}P$ and $^{90}Sr/^{90}Y$, with a relative difference of 1.95% and 0.43% between experimental and simulation efficiencies for $^{32}P$ and $^{90}Sr/^{90}Y$, respectively. However, owing to the short range of beta particles in water, the efficiency for $^{14}C$ was extremely low, and $^3H$ could not be detected. To directly measure the low-energy beta radionuclides considering their short range, a system where the source could flow directly to the scintillator was developed. The optimal thickness of the plastic scintillator was determined based on the suggested diameter. Results showed that the detection efficiency decreases with an increase in the depth of the water. The detection efficiency decreased drastically to approximately 10 cm, and the tendency was gradually constant.

• Journal of Electrical Engineering and Technology
• /
• v.10 no.4
• /
• pp.1726-1733
• /
• 2015

In order to study the effect of the high-altitude and dusty weather in northwest of China on the corona characteristics of transmission lines, a corona caged based experimental system with sandy and dusty flow condition is numerically investigated and designed. This system overcomes the difficulties caused by harsh environment and offers easy usage for off-site tests. The design parameters are mainly determined by the characteristics of strong sandstorm in northwest region and test requirements. By the comparison of numerical simulation of the particle diffusion in four programs with rectangular or circular air-duct, a practical technology, which introduces swirl to control the particle diffusion length, is obtained. Accordingly, the structure of round air-duct with swirl elbow in inlet and outlet of high level segment is selected as final program. Systems of control and measurement are designed at the same time. Field tuning results show that the test system could ensure the range of sandy and dusty coverage. The wind speed, sandy and dusty concentration could be controlled and meet the requirements of accuracy. The experimental system has many features, such as simple structure, easy to be assembled, disassembled, transported and operated, small space occupied.

• Journal of the Korean Society for Marine Environment & Energy
• /
• v.16 no.4
• /
• pp.255-262
• /
• 2013

The boltzmann equation is based on the particle distribution function while the Navire-Stokes equation based on the continuum theory. In order to simulate free surface flow, this paper used the Lattice Boltzmann Method of which is the discretized form. The detail study on the characteristics of the Lattice Boltzmann Method for the free surface simulation was investigated. The developed code was validated with the traditional dam breaking problem by tracking the front position of the water. A basic roles of density functions in the Lattice Boltzmann Method is discussed. To have an engineering applications, the simulation is also conducted the free surface behavior with an arbitrary wall geometry.

• Wind and Structures
• /
• v.31 no.4
• /
• pp.351-362
• /
• 2020

In this study, the impact of roof slope on the flow characteristics over low-sloped gable roofs was investigated using steady computational fluid dynamics (CFD) simulations based on a k-ω SST turbulence model. A measurement database of the flow field over a scaled model of 15° was created using particle image velocimetry (PIV). Sensitivity analyses for the grid resolutions and turbulence models were performed. Among the three common Reynolds-averaged Navier-Stokes equations (RANS) models, the k-ω SST model exhibited a better performance, followed by the RNG model and then the realizable k-ε model. Next, the flow properties over the differently sloped (0° to 25°) building models were determined. It was found that the effect of roof slope on the flow characteristics was identified by changing the position and size of the separation bubbles, 15° was found to be approximately the sensitive slope at which the distribution of the separation bubbles changed significantly. Additionally, it is suggested additional attention focused on the distributions of the negative pressure on the windward surfaces (especially 5° and 10° roofs) and the possible snow redistribution on the leeward surfaces.