• Journal of the Korean Society of Radiology
• /
• v.2 no.3
• /
• pp.19-25
• /
• 2008

Commercial analog x-ray detectors based on film cassettes have been showing problems such as with image storage and image transmission. Recently direct conversion material, photoconductor whit flat panel have been researched which generate the electron hole-pair (EHP). In this paper, we researched the electrical properties of the PbO and Lead(II) oxide PbO. film which fabricated by Particle-In-Binder(PIB) method. We compared tetragonal ${\alpha}$-PbO with orthorhombic ${\beta}$-PbO physical property. Tetragonal material was more than orthorhombic material in other paper. The solution was Poly Vinyl Butyral(PVB) in the PIB. We discussed about the sample of x-ray sensitivity, leakage current, Signal to Noise Rate and investigated SEM for the physical property of sample. We need to think more research ${\alpha}$-PbO material fabrication.

• Proceedings of the Korean Powder Metallurgy Institute Conference
• /
• 2006.09a
• /
• pp.160-161
• /
• 2006

Seasonal changes have been recognized in particle characteristics and forming characteristics of iron powder with insulated coating for a compacted magnetic core because of its high hygroscopicity, due to its phosphate coating and resin binder additives. For this reason, particle characteristics and molding characteristics of the powder with diverse water absorbtivity have been studied. The result shows that the higher the volume of absorbed water, the worse the fluidity becomes, resulting in the reduction in both springback during the molding process and expansion reduction after the heat treatment. The requirement on dimension accuracy for the finished product can be satisfied with an additional drying process on the material powder, which contributes to maintain its water volume constant.

• Proceedings of the Korean Institute of Building Construction Conference
• /
• 2007.04a
• /
• pp.51-54
• /
• 2007

This study investigates the properties of paste and mortar from different types and forms of silica fume on cement binder for ultra high strength. Although most Silica Fumes distributed in the market fulfill the KS quality standard, each type showed different levels of loss of ignition. When evaluating cement binder for ultra high strength in a form of paste. Flow, viscosity and moving freely time show great difference depending on the Silica Fume's form and type of primary particle's dispersibility. The evaluation of Silica Fume's dispersibility can be possible with the paste test since there is a high correlation of flow quality between paste and mortar. The compressive strength when using Silica Fume was correlated to the SiO2 content. Synthetically, selecting Silica Fume with the most the ideal primary particle is the key to optimizing the formation for cement binder for ultra high strength.

• Korean Journal of Metals and Materials
• /
• v.48 no.5
• /
• pp.401-409
• /
• 2010

This study was performed to develop an antibacterial film that can be dried at room temperature. A nanosized TiO$_2$ particle-dispersed solution was prepared by the hydrothermal treatment of peroxo-titanic acid at 160${^{\circ}C}$ for 4h. The binder was synthesized through the hydrolysis and condensation reactions of TEOS (10cc) and GPTS (3.5cc) in the mixture of H$_2$O (30cc) and EtOH (30cc). The synthesized binder was mixed with 0.1 M of TiO$_2$ solution in a volume ratio of binder/TiO$_2$ solution=0.25~0.5. The glass substrate was coated after using the dip coating method, which was then followed by drying for over 2h at room temperature. Although the TiO$_2$ particles did not chemically-bond to the binder, the coating layer strongly adhered to the substrate and displayed good antibacterial properties.

• Proceedings of the Korean Institute of Building Construction Conference
• /
• 2011.05a
• /
• pp.77-78
• /
• 2011

This study is analysis of effect of binder types and replacement ratio on the properties of blast furnace slag mortar using the recycled fine aggregates. The results of the study were was follows. Compressive strength was increased according to an increase in replacement ratio of fine particle cement and gypsum. Absorption was reduced according to an increase in replacement ratio of fine particle cement and recycled aggregate fine powder.

• Journal of Korea Technical Association of The Pulp and Paper Industry
• /
• v.41 no.3
• /
• pp.8-12
• /
• 2009

According to a previous study, talc as a coating pigment can improve the viscosity and the water retention of coating color, the compressibility of coating layer, and hence gravure printability. Talc is also well known for its larger particle size than other pigments, which implies that less binder may be need due to its smaller specific surface area. This study investigated the possibility of reducing binder content for matte grade paper. Coating color was prepared with the Cotalc-2000, which showed the best properties in the previous study. The binder content was varied and the effect of binder content on the physical properties of coated paper and the gravure printability was investigated. It was shown that binder content could be reduced when talc was used as a coating pigment. The reduction in binder content did not influence gloss, roughness and the print density of coated paper but showed improvement in paper porosity, compressibility and missing dot.

• Journal of the Korean Ceramic Society
• /
• v.36 no.6
• /
• pp.625-631
• /
• 1999

Ceramic tapes were fabricated by ultrasonically spraying slurries of monodispersed spherical and alumina powders. Effects of slurry compositions on tape forming were investigated. A relatively fast rate of solvent evaporation caused pores and cracks to be formed. A good chemical affinity between solvent and binder gave rise to binder separation resulting in inhomogeneous distribution of binder. Defect-free silica tapes with uniform distribution of particle packing and the binder were obtained from the solvent having a low chemical affinity and a slow evaporation rate and containing appropriate amounts of the binder and the plasticizer. Tape thickness could be controlled by adjusting solids loadings and slurry feed rates. It was possible to fabricate a tape in 15 $\mu\textrm{m}$ thickness from 7 vol% alumina slurry.

• Applied Chemistry for Engineering
• /
• v.24 no.6
• /
• pp.668-671
• /
• 2013

This paper describes activated carbon block filters prepared by extrusion for water purifier. The specific surface area of the activated carbon blocks affecting the properties of a polymer binder were investigated. Polyethylene (PE) particles were used as a binder polymer and the effect of particle sizes on changes in the specific surface area of activated carbon blocks in addition to the adsorption properties of chloride anion in the aqueous solution were investigated. The sizes and shapes of PE particles were measured using SEM. The specific surface area of activated carbon was $1186m^2/g$. The specific surface area of PE binder was $444m^2/g$ and $940m^2/g$ with the particle sizes of $200{\mu}m$ and $20{\mu}m$, respectively. In order to verify the performance of the filter, chlorine adsorption experiments were conducted.

• Journal of Adhesion and Interface
• /
• v.11 no.3
• /
• pp.112-119
• /
• 2010

Poly(methyl methacrylate)/poly(butyl acrylate) PMMA/PBA core-shell composite particles were prepared by the emulsion polymerization of MMA and BA in the presence of different concentration of sodium dodecyl benzene sulfonate (SDBS). The following conclusions are drawn from the measured conversion and particle size distribution, morphology, average molecular weight distribution, observation of film formation and particle formation, glass transition temperature and physical properties of polymerized core-shell composition particles for using adhesive binder. When the concentration of 0.03 wt% surfactant, the conversions of PMMA and PBA core polymerization are excellent as 95.8% for PMMA core and 92.3% for PBA core. Core-shell composite particles are obtained 90.0% for PMMA/PBA core-shell composite particles and 89.0% for PMMA/PBA core-shell composite particles. It is considered that the core and shell particles are polymerized to be confirmed FT-IR spectra and average molecular weight measured with a GPC, formation of the composite particles is confirmed by the film formation from normal temperature, and composition of inside and outside of the composite particle is confirmed by TEM photograph. The synthesized polymer has two glass transition temperatures, suggesting that the polymer is composed of core polymer and shell polymer unlike general copolymers. It is considered that each core-shell composite particle can be used as a high functionality adhesion binder by the measurement of tensile strength and elongation.

• Textile Coloration and Finishing
• /
• v.32 no.1
• /
• pp.19-26
• /
• 2020

The previous study reported that the quaternary copolymer of MMA, BA, MAA, and NEA was expected to be a good monomer composition for a binder polymer with good rubbing fastness for digital textile printing(DTP) pigment ink. However, the rubbing fastness of the dyed fabric with the quaternary copolymer binder containing pigment ink is not enough to be commercially used. Therefore, this study aims to optimize MMA:BA:MAA:NEA composition for improved rubbing fastness. And the binder polymer with various MMA:BA:MAA:NEA compositions were synthesized using miniemulsion polymerization. The particle size, viscosity, molecular weight, and Tg of the synthesized binder were evaluated. And the color strength and rubbing fastness of the black pigment ink dyed cotton fabrics with the prepared binders were also evaluated. Then, the stiffness of undyed and dyed cotton fabrics were evaluated to investigate the changes in touch as the binder structure changes.