• 한국신재생에너지학회:학술대회논문집
• /
• 2006.11a
• /
• pp.443-446
• /
• 2006

Carbon-supported Platinum (Pt) is the potential electro-catalyst material for anodic and cathodic reactions in fuel cell. Catalytic activity of the metal strongly depends on the particle shape, size and distribution of the metal in the porous supportive network. Conventional preparation techniques based on wet impregnation and chemical reduction of the metal precursors often do not provide adequate control of particle size and shape. We have proposed a novel route for preparing nano sized Pt colloidal particles in solution by oxidation of ethylene glycol. These Pt nano particles were deposited on large surface area carbon support. The process of nano Pt colloid formation involves the oxidation of solvent ethylene glycol to mainly glycolic acid and the presence of its anion glycolate depends on the solution pH. In the process of colloidal Pt formation glycolate actsas stabilizer for the Pt colloidal particle and prevents the agglomeration of colloidal Pt particles. These mono disperse Pt particles in carbon support are found uniformly distributed in nearly spherical shape and the size distribution was narrow for both supported and unsupported metals. The average diameter of the Pt nano particle was controlled in the range off to 3 nm by optimizing reaction parameters. Transmission electron microscopy, CV and RRDE experiments were used to compliment the results.

• Journal of The Korean Society of Agricultural Engineers
• /
• v.57 no.6
• /
• pp.107-115
• /
• 2015

The objective of the this study is to find the breakage index and changes in permeability of Bottom ash from thermoelectric power plants in Korea. Bottom ash was crushed by compaction according to compaction energy from 0 to $1661.4\;kN/m^2$. The particle size distribution was estimated by sieve analysis. The various breakage indexes were used for analyzing the change in particle size distribution and effect of compaction energy. In the result, breakage indexes were increased as compaction energy and initial upper 4.75 mm diameter ratio, but values and tendencies of breakage indexes appeared in different as calculation method of breakage indexes. The coefficient of permeability was decreased with particle breakage, but decreasing ratio of permeability was very small. Bottom ash has a higher permeability than the weathered soil and it is considered high usability as a permeable materials.

• Macromolecular Research
• /
• v.16 no.2
• /
• pp.120-127
• /
• 2008

Glycidyl methacrylate linked poly(dimethylsiloxane) (GMA-PDMS) was synthesized and used as a stabilizer for the dispersion polymerization of methyl methacrylate (MMA) in supercritical $CO_2$. This study examined the effect of the concentrations of the stabilizer, 2,2'-azobisisobutyronitrile (AIBN) initiator, and MMA on the yield, molecular weight, and morphology of the poly(methyl methacrylate) (PMMA) product. PMMA was obtained in 94,6% yield using only 0,87 wt% GMA-PDMS, When the AIBN concentration was increased from 025 to 1.06 wt%, the molecular weight and particle size of the PMMA decreased from 56,600 to 21,600 and from 4.1 to $2.7{\mu}m$, whereas the particle size distribution increased from 1.3 to 1.9. The $M_n$ of the PMMA product ranged from 41,600 and 55,800 under typical polymerization conditions. The PMMA particle diameter ranged from 1.8 to $11.0{\mu}m$ and the particle size distribution ranged from 1.4 to 1.8.

• Korean Journal of Materials Research
• /
• v.29 no.4
• /
• pp.264-270
• /
• 2019

As a case study on aspect ratio behavior, Kaolin, zeolite, $TiO_2$, pozzolan and diatomaceous earth minerals are investigated using wet milling with 0.3 pai media. The grinding process using small media of 0.3 pai is suitable for current work processing applications. Primary particles with average particle size distribution D50, ${\sim}6{\mu}m$ are shifted to submicron size, D50 ${\sim}0.6{\mu}m$, after grinding. Grinding of particles is characterized by various size parameters such as sphericity as geometric shape, equivalent diameter, and average particle size distribution. Herein, we systematically provide an overview of factors affecting the primary particle size reduction. Energy consumption for grinding is determined using classical grinding laws, including Rittinger's and Kick's laws. Submicron size is obtained at maximum frictional shear stress. Alterations in properties of wettability, heat resistance, thermal conductivity, and adhesion increase with increasing particle surface area. In the comparison of the aspect ratio of the submicron powder, the air heat conductivity and the total heat release amount increase 68 % and 2 times, respectively.

• Journal of Powder Materials
• /
• v.15 no.3
• /
• pp.227-233
• /
• 2008

Dynamic plastic deformation behavior of copper particles occurred during the cold spray processing was numerically analyzed using the finite element method. The study was to investigate the impact as well as the heat transfer phenomena, happened due to collision of the copper particle of $20{\mu}m$ in diameter with various initial velocities of $300{\sim}600m/s$ into the copper matrix. Effective strain, temperature and their distribution were investigated for adiabatic strain and the accompanying adiabatic shear localization at the particle/substrate interface.

• Proceedings of the KSME Conference
• /
• 2004.04a
• /
• pp.1510-1515
• /
• 2004

The effects of additive ions on the generation of metallic nanoparticles were evaluated using a corona induced supersonic nozzle. Applying the corona discharge to the nanoparticle generator, a tungsten needle and the supersonic nozzle are used as an anode electrode and a cathode electrode respectively. The corona ions act as nuclei for the silver vapor condensation. The ion density was controlled precisely as varying the applied voltage between electrode and nozzle. The mean diameter of the silver particle decreases as the ion density increases. However, the number concentration of the silver particle tended to increase with the ion density. The size distribution is more uniform as the ion density increases.

• Particle and aerosol research
• /
• v.18 no.3
• /
• pp.69-77
• /
• 2022

In order to understand the characteristics of fine particles emitted from coal-fired power plant stacks, it is important to analyze the size distribution and components of particles. In this study, particle size distributions were measured using the ejector-porous tube dilution device and an ELPI system at a stack in a coal-fired power plant. Main elemental components of particles in each size interval were also identified through TEM-EDS analysis for the particles collected in each ELPI stage. Particle size distributions based on number and mass were analyzed with component distributions from 0.006 to 10 ㎛. The highest number concentration was about 0.01 ㎛. The main component of the particles consisted of sulfur, which indicated that sulfate aerosols were generated by gas-to-particle conversion of SO2. In a mass size distribution, a mono-modal distribution with a mode diameter of about 2 ㎛ was shown. For the components of PM1.0 (particles less than 1 ㎛), the abundance order was F > Mg > S > Ca, and however, for the components of PM10 (particles less than 10 ㎛), it was in the order of Fe > S > Ca > Mg. The elemental components by particle size were confirmed.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.17 no.4
• /
• pp.55-62
• /
• 2009

As an experiment investigation, the effects of ethanol blended gasoline fuel with different injection method on nano-sized particle emission characteristics were examined in a 0.5L spark-ignited single-cylinder engine with a compression ratio of 10. Because this engine nano-particles are currently attracting interest due to its adverse health effects and their impact on the environments. So a pure gasoline and an ethanol blended gasoline fuels, namely E85 fuel, used for this study. And, as a particle measuring instrument, a fast-response particle spectrometer (DMS 500) with heated sample line was used for continuous measurement of the particle size and number distribution in the size range of 5 to 1000nm (aerodynamic diameter). As this research results, we found that the effect of ethanol blending gasoline caused drastic decrease of nano-particle emissions when port fuel injection was used for making better air-fuel mixture than direct fuel injection. Also injection timing, specially direct fuel injection, could be a dominant factor in controlling the exhaust particle emissions.

• Journal of the Korean Applied Science and Technology
• /
• v.20 no.4
• /
• pp.332-340
• /
• 2003

Crosslinked poly(methyl methacrylate) particles from 2.4 to $8.1{\mu}m$ in diameter were prepared by homogenized suspension polymerization. The effect of polymerization parameters such as homogenizing speed, homogenizing time and stabilizer concentration on the particle size were examined. Optical diffusion films were prepared with the crosslinked poly(methyl methacrylate) particles. The effect of film thickness, particle size, and particle size distribution on transmittance and haze of optical diffusion film was examined. Transmittance of optical diffusion film increased with increasing particle size and decreasing film thickness. Haze increased with increasing film thickness and decreasing particle size. We also found the existence of an optimum ratio for optical performance when the mixture of small particle and large particle was used.

• Korean Journal of Materials Research
• /
• v.23 no.12
• /
• pp.737-744
• /
• 2013

We demonstrated size control of Au nanoparticles by heat treatment and their use as a catalyst for single-walled carbon nanotube (SWNTs) growth with narrow size distribution. We used uniformly sized Au nanoparticles from commercial Au colloid, and intentionally decreased their size through heat treatment at 800 oC under atmospheric Ar ambient. ST-cut quartz wafers were used as growth substrates to achieve parallel alignment of the SWNTs and to investigate the size relationship between Au nanoparticles and SWNTs. After the SWNTs were grown via chemical vapor deposition using methane gas, it was found that a high degree of horizontal alignment can be obtained when the particle density is low enough to produce individual SWNTs. The diameter of the Au nanoparticles gradually decreased from 3.8 to 2.9 nm, and the mean diameter of the SWNTs also changed from 1.6 to 1.2 nm for without and 60 min heat treatment, respectively. Raman results reconfirmed that the prolonged heat treatment of nanoparticles yields thinner tubes with narrower size distribution. This work demonstrated that heat treatment can be a straightforward and reliable method to control the size of catalytic nanoparticles and SWNT diameter.