• Resources Recycling
• /
• v.24 no.4
• /
• pp.12-21
• /
• 2015

Almost all copper slags contain a considerable amount of Cu (0.5 - 3.7%) close to or even higher than copper ores. A number of methods for metal recovery from copper slag were reported These methods can be classified into three categories, flotation, leaching and roasting. Sulfide flotation method for the recovery of copper from Kazahstan copper furnace slag is discussed in this investigation. 50% of copper from the slag was recovered by sulfide flotation at pH 4. meanwhile 67% of copper from the slag was recovered at pH 11. Higher copper recovery result at pH 11 rather than that at pH 4 was caused by the fact that copper sulfides were floated in particle size fraction over $100{\mu}m$ in concentrates at pH 11. When the slag were ground below $74{\mu}m$by ball milling, the recovery of copper by floation in slag improved to 78 - 83% because of copper liberation effect.

• Journal of the Korean GEO-environmental Society
• /
• v.13 no.8
• /
• pp.65-73
• /
• 2012

Soil-rock interface, mainly founded in Granite region of Korea, is known as one of the important factor of the slope failure at the rainfall due to smaller shear strength than soil itself. However, research of the effect on slope stability by soil-rock interfaces is insufficient. Therefore, a series of direct shear tests were performed in order to investigate the effect of soil-rock interface on slope stability. The method of tests is to get sand itself and sand-artificial rock interface shear strength from different grain size of sands and artificial rock samples. The results of tests show that the friction angle of interface depends primarily on particle size and surface roughness. Interface friction angle ratio ${\mu}(={\delta}/{\Phi})$ is in the range of 0.75 ~ 0.96, this results indicate that interface friction angle is smaller than sand itself.

• Proceedings of the KSRS Conference
• /
• 2002.10a
• /
• pp.208-208
• /
• 2002

Relationship between chlorophyll a in the East China Sea and spectral bands (412, 443,490, (510), 555, (676,765) in) of OSMI (Ocean Scanning Multi-Spectral Imager) including the profile multi-spectral radiometer (PRR-800) was studied. The values of remote sensing reflectance (Rrs) at the bands corresponding to the field chlorophyll a in α in the East China Sea were much higher than those in clear waters off California, USA. In case of the particle absorptions related to the chlorophyll a concentration at the spectral bands (440, 670 nm) were much higher in the East China Sea than the ones in the clean waters off California. The normalized water leaving radiances (nLw) at 412, 443, 490, 555 m of OSMI and field chlorophyll a in the East China Sea were correlated each other. According to the results, the relationship between field chlorophyll a and nLw 410 m in OSMI bands was the lowest, whereas that between the field chlorophyll a and nLw 555 nm in the bands was the highest. Reciprocal action between the field chlorophyll a and the band ratio of the OSMI bands (nLw410/nLw555, nLw443/nLw555, nLw490/nLw555) was also studied. Correlation between the chlorophyll a and the band ratio (nLw490/nLw555) was highest in the OSMI bands. Relationship between the chlorophyll a and the ratio (nLw443/nLw555) was higher than one in the nLw410/nLw555. The difference in the estimated chlorophyll α (mg/m3) between OSMI and SeaWiFS (Sea Viewing Wide Field-of-View Sensor) at the special observing stations in the northern eastern sea of Jeju Island in february 25, 2002 was about less than 0.3 mg/m3 within 3 hours. It is suggested that OC2 (ocean color chlorophyll 2 algorithm) be used to get much better estimation of chlorophyll α from OSMI than the ones from the updated algorithms as OC4.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2005.07a
• /
• pp.388-389
• /
• 2005

In this paper, the electric properties of mercury Iodide multi-layer samples has been investigated. We measured and analyzed their performance parameters such as the X-ray sensitivity and dark-current for a mercury Iodide multi-layer X-ray detector with a dielectric layer. The digital X-ray image detector can be constructed by integrating photoconduction multi-layer that dielectric layer has characteristics of low dark-current, high X-ray sensitivity. However this process has found to have complexity on the performance of the sample. We have investigate dielectric layer that it substitute dielectric layer for HgO(Mercury Oxide). We have employed two approaches for producing the mercury Iodide sample : 1) Physical Vapor Deposition(PVD) and 2) Particle-In-Binder(PIB). In this paper fabricated by PIB Method with thicknesses ranging from approximately 180um to 240um and we could produce high-quality samples for each technique particular application. As results, the dielectric materials such as HgO between the dielectric layer and the top electrode may reduce the dark-current of the samples. Mercury Iodide multi-layer having HgO has characteristics of low dark-current, high X-ray sensitivity and simple processing. So we can acquired a enhanced signal to noise ratio. In this paper offer the method can reduce the dark-current in the X-ray detector.

• Applied Chemistry for Engineering
• /
• v.23 no.2
• /
• pp.138-142
• /
• 2012

The ${\epsilon}$ type copper phthalocyanine (${\epsilon}$-CuPc), called as a pigment blue 15 : 6, is a significant material to produce a blue pixel in LCD (Liquid Crystal Display) panel. In this study, ${\epsilon}$-CuPc sample was synthesized at various reaction conditions by applying the seed method using ${\epsilon}$-CuPc nanoparticles as a seed. Adequate synthetic conditions of the samples were selected by analyzing and comparing crystalline structure, crystalline purity, microstructure, and synthetic yield of the samples with ${\alpha}$ and ${\beta}$ crystalline CuPc samples. The chemical and crystalline structure of the samples were tested using FT-IR spectrometer and X-ray diffractometry, respectively. The shape of the particle was examined using field emission scanning electiron microscope while the thermal property was tested utilizing thermogravimetric analysis.

• Journal of the Korean Geotechnical Society
• /
• v.36 no.9
• /
• pp.21-32
• /
• 2020

In this study, series of cyclic triaxial tests and shear velocity measurement were conducted using Pohang sand, which was taken from liquefaction observed area, to verify the liquefaction characteristics of Pohang. The cyclic resistance ratio(CRR) was derived based on the test results. A specimen was reconstituted into 40% and 80% relative density conditions and then a series of cyclic triaxial tests and shear-wave velocity measurement were conducted. As a result, the effect of particle distribution and relative density to liquefaction resistance was verified. The liquefaction resistance of Pohang sand was evaluated by comparing with other liquefaction resistance of sands from previous research. In addition, the liquefaction resistance curve from field observation data was used to verify the reliability of results from this study by measured shear-wave velocity.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.18 no.5
• /
• pp.12-18
• /
• 2014

A study of gas generator Fuel-Rich propellant for air-breathing propulsion system was performed in this paper. General solid propellant comprises a mean of 60% or more oxidizing agents. but, to develop the fuel-rich solid propellant increased the content of the metal fuel and reduced the content of the oxidizing agents by approximately 30%. Very high amount of heat per volume of fuel into the metal having the Boron was used. Amorphous Boron Powder was applied to propellant as beads type and it allowed to design more amount of metal fuel in the fuel-rich propellant. And the Combustion characteristics and properties of fuel-rich solid propellant according to the Boron-bead sizes were confirmed.

• Journal of the Korean Society of Marine Environment & Safety
• /
• v.12 no.2 s.25
• /
• pp.99-106
• /
• 2006

The fate of chemical pollutants in the aquatic environment is generally considered to be strongly influenced by environmental factors such as pH, salinity and electrostatic charges on the surface of particles ai well as by the characteristic of chemicals. Oxolinic acid was measured by chemical analysis using HPLC to determine the effect of salinity, pH and suspended solids on chemical binding and by bioassay for measuring bioactivity. The higher contentration of suspended solids in the medium, the lower concentration of oxolinic and was detected in measurements from by both HPLC and biosssay analysis. This indicates particle may have a stronger binding or absorption effect on oxolinic acid. Bioassay analysis showed weaker bioacivity at higher salinity and pH 7.0, but this result of bioassay analysis was different from the result of HPLC.

• Elastomers and Composites
• /
• v.40 no.4
• /
• pp.249-257
• /
• 2005

Polyurethane(PU) prepolymers were prepared from polyol and diisocyanate. Unionized PU prepolymers were synthesized from poly(propylene glycol)(PPG, MW: 1000), 2,2-bis (hydroxymethyl) propionic acid(DMPA), and isophorone diisocyanate(IPDI) by prepolymer syhthesizing process. After PU prepolymers were dispersed into water, the physical properties were investigated by changing the molar ratio of polyol and diisocyanate. The results showed a stable state with the best physical properties when the prepolymer was composed of PPG/DMPA with hard segment=40%, NCO%=3.43%, [NCO]: [OH]=1.5: 1.0 in molar ratio, and was dispersed into water with 30% solid content. PU prepolymers also were synthesized with various molar ratio of PPG and DMPA. Upon higher molar ratio of DMPA, particle size of polyurethane dispersion(PUD) gradually decreased. PU-prepolymers prepared from the various blocking agents represented characteristic initial deblocking temperatures that depended on the blocking agents, and the beginning of deblocking occured within 30 mins on all the blocking agents used.

• Journal of the Korean Magnetics Society
• /
• v.5 no.5
• /
• pp.366-371
• /
• 1995

High performance magnetic materials are characterized by the combination of outstanding magnetic properties and optimized microstructures, e.g., nanocrystalline composites of multilayers and small particle systems. The characteristic parameters of the hysteresis loops of these materials vary over more than a factor of $10^{6}$ with optimum values for the coercive field of several Tesla and permeabilities of $10^{6}$. Within the framework of the computational micromagnetism (nanomagnetism) using the finite element method the upper and lower bounds of the coercive field of different types of grain ensembles and multilayers have been determined. For the case of nanocrystalline composites the role of grain size, exchange and dipolar coupling between grains and the degree of grain alignment will be discusses in detail. It is shown that the largest coercivities are obtained for exchange decoupled grains, whereas remanence enhancing requires exchange coupled grains below 20 nm. For composite permanent magnets based on $Nd_{2}Fe_{14}B$ with an amount of ~ 50% soft $\alpha$-Fe-phase coercivities of ${\mu}_{0}H_{c}=0.75\;T$, a remanence of 1.5 T and an energy product of $400\;kJ/m^{3}$ is expected. In nanocrystalline systems the temperature dependence of the coercivity is well described by the relation ${\mu}_{0}H_{c}=(2\;K_{1}/M_{s}){\alpha}-N_{eff}{\mu}_{0}M_{s}$, where the microstructural parameters $\alpha$ and $N_{eff}$ take care of the short-range perturbations of the anisotropy and $N_{eff}$ is related to the long-range dipolar interactions. $N_{eff}$ is found to follow a logarithmic grain size size dependence ${\mu}_{0}H_{c}=(2\;K_{1}/M_{s}){\alpha}-N_{eff}(\beta1nD){\mu}_{0}M_{s}$. Several trends how to achieve the ideal situation $\alpha$->1 and $N_{eff}$->1->0 will be discussed.