• 대한용접접합학회:학술대회논문집
• /
• 대한용접접합학회 2003년도 춘계학술발표대회 개요집
• /
• pp.84-86
• /
• 2003

The laser welding and its analysis of thin-sheet carbon steels were carried out with high power CO$_2$1aser. Bead on plate welding of thin sheet was examined to investigate the effect of weld variables of laser welding, and to obtain optimum welding condition. Butt-welding was also carried out to show the effect of gap on the laser weldability of thin sheet. At high welding speed, the partial penetration was obtained by low heat input. Otherwise, porosity was formed in the bead at low weld speed because of too many heat input. The maximum gap tolerance on laser welding was observed to be about 0.2mm. This gap size has good relationship with beam size of laser spot(about 0.3mm). The formability of welded sheet was about 80% value of base metal and the gap size has not affected on the formability, although weld quality is dependent on the gap size.

• Journal of Welding and Joining
• /
• 제23권1호
• /
• pp.48-54
• /
• 2005

Laser keyhole welding is investigated using a three-dimensional Gaussian heat source, and the heat source parameters such as the keyhole depth, welding efficiency and power density distribution factor are determined in a systematic way. For partial penetration, the keyhole depth is same as the penetration and is predicted using the experimental data. The welding efficiency is calculated using the ray-tracing method and the power density distribution factor is determined from the bead shape. Full penetration is classified into the transition, normal and excessive modes depending on the degree of keyhole opening. Thermal analysis of the bead-on-plate welds is conducted using the Gaussian heat source, and the calculated weld geometries show reasonably good agreements with the experimental results.

• Journal of Advanced Marine Engineering and Technology
• /
• 제26권4호
• /
• pp.464-471
• /
• 2002

Porosity formation in partial penetration welds by high power lasers is a serious problem in industry. There are two main causes that induce porosity formation. One form of porosity is due to gases (e.g. hydrogen, oxygen) dissolving into the weld pool because of the high temperature and then the rapid solidification traps gases as a bubble in the weld metal. The second problem is voids formed by the keyhole collapsing due to unstable keyhole fluid dynamics. The voids that form at the bottom of the keyhole are relatively large and irregular in shape compared to the gas bubbles; this void formation is the primary concern in this paper. The reduction of voids formed by keyhole collapse is achieved by improving the stability of keyhole. Two methods to improve keyhole stability are discussed in this paper: pulse modulation and beam incident angle. Pulse modulation of the laser beam was performed between 100 Hz and 500 Hz to find out the optimum frequency for the keyhole dynamics. The incident beam angle changed the impact angle of the laser beam to the work surface in a range of 0 to 25 degrees. Glycerin in a semi-solidified state is used as a medium for performing the welding because its transparency allows of visualization of the keyhole.

• Journal of Welding and Joining
• /
• 제14권4호
• /
• pp.33-42
• /
• 1996

In recent years there has been a significant growth in the use of the automated and/or robotic welding system, carried out as a means of improving productivity and quality, reducing product costs and removing the operator from tedious and potentially hazardous environments. One of the major difficulties with the automated and/or robotic welding process is the inherent lack of mathematical models for determination of suitable welding process parameters. Partial-penetration, single-pass bead-on-plate welds were fabricated in 12mm AS 1204 mild steel flats employing five different welding process parameters. The experimental results were used to develop three empirical equations: curvilinear; polynomial; and linear equations. The results were also employed to find the best mathematical equation under weld bend width to assist in the process control algorithms for the Gas Metal Arc Welding(GMAW) process and to correlate welding process parameters with weld bead width of bead-on-plates deposited. With the help of a standard statistical package program. SAS, multipe regression analysis was undertaken for investigating and modeling the GMAW process, and significance test techniques were applied for the interpretation of the experimental data.

• 한국강구조학회 논문집
• /
• 제20권6호
• /
• pp.817-827
• /
• 2008

본 연구에서는 기존 SM490강재와 국내에서 최근 개발된 내진용강재(SHN490, SN490)로 이루어진 특수모멘트골조의 기둥이음부를 부분용입용접으로 설계하여 내진성능평가를 위한 실물대 실험을 실시하였다. 부분용입용접에 의한 기둥이음부는 용접비용 및 공기의 절감에서 매력적 인 방안이다. 그러나 과거에 외국에서 수행된 몇몇 실험결과에 의하면 부분용입용접에 의한 후판기둥의 이음부는 인장응력에 대해 취성파단하는 거동을 보였다. 이런 이유로 인해 최근의 내진설계기준에서는 특수모멘트골조의 부분용입용접 기둥이음부의 강도는 예상 기둥소성모멘트 이상의 강도를 요구한다. 이를 반영하여 시험체의 부분용입용접 이음부의 설계강도는 AISC-LRFD의 기준식을 적용하여 기둥의 예상 소성모멘트 이상이 되도록 설계 및 제작하고 3등분점 하중으로 단조가력하였다. 압연형강 시험체 2개 및 조립형강 시험체 2개(총 4개 시험체)의 이음부 모두에서 기둥의 실제 소성모멘트 이상의 강도를 발휘하였다. 즉 AISC-LRFD의 부분용입용접 설계강도식의 신뢰성을 확인할 수 있었다. 다만 SM490 압연형강 시험체는 기둥의 소성모멘트를 발휘한 후 이음부에서 급격한 취성파단이 발생하였다. 이는 용접결함과 플랜지의 강도미달에 따른 복합적 원인에 의한 것으로 추정된다. 특히 SM490 강재의 경우는 항복강도와 인장강도가 규정치에 미달하는 등 성능편차가 큰 것으로 나타났다. 제한적 실험결과이긴 하지만 소재물성 및 이음부 거동의 측면 모두에서 내진용 신강재가 기존강재에 비해 전체적으로 우수함을 보여준 결과라 할 수 있다.

• KSII Transactions on Internet and Information Systems (TIIS)
• /
• 제14권3호
• /
• pp.1086-1103
• /
• 2020

The automatic identification and classification of image-based weld defects is a difficult task due to the complex texture of the X-ray images of the weld defect. Several depth learning methods for automatically identifying welds were proposed and tested. In this work, four different depth convolutional neural networks were evaluated and compared on the 1631 image set. The concavity, undercut, bar defects, circular defects, unfused defects and incomplete penetration in the weld image 6 different types of defects are classified. Another contribution of this paper is to train a CNN model "RayNet" for the dataset from scratch. In the experiment part, the parameters of convolution operation are compared and analyzed, in which the experimental part performs a comparative analysis of various parameters in the convolution operation, compares the size of the input image, gives the classification results for each defect, and finally shows the partial feature map during feature extraction with the classification accuracy reaching 96.5%, which is 6.6% higher than the classification accuracy of other existing fine-tuned models, and even improves the classification accuracy compared with the traditional image processing methods, and also proves that the model trained from scratch also has a good performance on small-scale data sets. Our proposed method can assist the evaluators in classifying pipeline welding defects.

• 대한조선학회논문집
• /
• 제33권3호
• /
• pp.1-7
• /
• 1996

용접이음부재에서 피로강도에 큰 영향을 미치는 용접부의 응력집중계수를 추정하였다. 여기서는 하중전달형 십자필렛용접이음부를 그 대상으로 하였다. 필렛용접이음부에서 토우파괴를 일으키는 피로균열발생부인 용접토우부의 응력집중계수를 구하기 위해 인장하중하에서 토우부의 적정 요소 크기를 검토하고 여러 파라메타들의 값을 변화시켜 유한요소 응력해석을 수행하였다. 즉 용접토우부의 형상인 토우각 및 곡률반경의 영향과 용입부족부 길이의 변화를 동시에 고려한 응력집중계수를 정량적으로 구하였다. 그리고 그 결과를 이용하여 응력집중계수 추정식을 유도하였다.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 2004년도 춘계학술대회 논문집
• /
• pp.365-372
• /
• 2004

1)고강도강 BOP 시험 결과 강종에 차이 없이 용접속도에 따라 유사한 비드 형상을 가지는 것으로 나타났다. 한편 1.2t 시험편의 적정 용접속도는 $4\~8m/min$으로 나타났다. 2) 용접속도가 빠를수록 비드폭은 작아지며, 경도값은 높게 나타났다. 그리고, 최고 경도값은 강의 성분(Ceq)에 비례하는 것으로 나타났음, 그 결과 TRIP80(Ceq=0.53)의 경우 최고 520Hv이상의 경도값을 가지고 있었다. 3) LDH test 결과 DP강의 모재대비 용접부의 성형성이 약 $90\%$ 정도로 나타났으며, TRIP 및 일반 고강도강은 약 $80\%$의 성형성을 갖는 것으로 확인되었다. 4) He을 보호가스로 사용시 기공의 형성은 크게 억제되었다. 그리고 Ar 사용시에는 기공 형성이 He에 비해 많이 형성되는 것으로 나타나 사용시 주의가 필요한 것으로 보인다. 기공 형성은 TRIP > 60C/45R > DP 순서로 나타나 DP강이 가장 좋은 레이저 용접성을 가지고 있었다.

• Journal of Welding and Joining
• /
• 제34권6호
• /
• pp.69-74
• /
• 2016

Because the pure titanium has superior corrosion resistance and formability compared with different material, it is widely used as material of welded heat exchanger. When the welding of heat exchanger is carried out, certain area in which welding start and end are overlapped occurs. The humping of back bead is formed in the overlap area due to partial penetration. Thus in this study, the experiments were carried out by changing the length and wave shape of overlap area, and then the weldabiliay was evaluated through the observation of microstructure, the measurement of hardness and tensile-shear strength test in the overlap area. When overlap length was 9.8mm, humping bead was suppressed. The microstructure of overlap area coarsened and its hardness increased due to remelting. As a result of tensile-shear strength test in the overlap area according to applying the wave shape control, it was confirmed that the overlap area applied wave shape control had more excellent yield strength and ductility.

• 대한용접접합학회:학술대회논문집
• /
• 대한용접접합학회 2002년도 Proceedings of the International Welding/Joining Conference-Korea
• /
• pp.620-625
• /
• 2002

Considering the fuel consumption of car, a light structure of aluminum alloys is desired for car body nowadays. However, fusion welding of aluminum alloys has some problems of reduction of joint efficiency, porosity formation and hot cracking. ill the present work, investigation to improve the joint performance of laser welded joint has been carried out by addition of Cu, Ni, and Zr to A6N01 alloy welds. Aluminum alloy plate of 2.0mm in thickness with filler metal bar was welded by twin beam Nd:YAG laser facility (total power:5kW). The filler metals were prepared by changing the chemical compositions for adding the elements into the weld metal. Thirteen filler metal bars were prepared and pre-placed into the base metal before welding. Ar gas shielding with a flow rate of 10 l/min was used. The defocusing distance is kept at 0 mm. At travel speeds of 3 to 9 m/min and at laser power of 5kW (front beam 2kW rear beam 3kW), full penetration welds were obtained, whereas at travel speeds of 12 to 18 m/min and same power, partial penetration was observed. The joint efficiency of laser-welded joint was improved by the addition of Cu, Ni, and Zr due to the solid solution hardening, grain refining and precipitation hardening. The type of hardening has been further considered by metallurgical examination.