• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.25 no.3A
• /
• pp.325-333
• /
• 2000

The proposed RPSS(Reference Picture Segment Selection) mode is the RPS mode in picture segment of the ISD mode. The RPS mode has the weakness that it has to change the whole reference picture even if transmission error occurs only in the small part of picture. If the RPS mode is applied only to an error-occurred part and a conventional coding scheme is applied to an error-free part, the higher coding efficiency can be obtained. Simulation results show that there is the optimal number of segment which provides that best performance with given environment such as the BER(Bit Error Rate) of wireless channels, the characteristics of imput sequence, what kind of RPSS mode is used, etc. To apply the channel-adoptive RPSS mode later, the scheme which can change the number of segment without INTRA refresh and spatial error propagation is proposed in this paper.

• Journal of information and communication convergence engineering
• /
• v.9 no.6
• /
• pp.661-665
• /
• 2011

This paper presents the method for the extraction of the lungs part from the other parts for the diagnostic of the lungs part. The proposed method is based on the calculation of the connected component and the centroid of the image. Connected Component labeling is used to label the each objects in the binarized image. After the labeling is done, centroid value is calculated for each object. The filing operation is applied which helps to extract the lungs part from the image retaining all the parts of the original lungs image. The whole process is explained in the following steps and experimental results shows it's significant.

• Transactions of Materials Processing
• /
• v.12 no.2
• /
• pp.134-140
• /
• 2003

Polymers such as polypropylene or polyethylene offer a unique feature of producing an integral hinge, which can flex over a million times without causing a failure. With such advantage manufacturing, time and cost required at the assembly stage can be eliminated by injecting the whole part as one piece. However, due to increased fluidity resistance at hinges during molding, several defects such as short shot or premature hinge failure can occur with the improper selection of gate locations. Therefore, it is necessary to optimize flow balancer in injection molding of part with hinges before actually producing molds. In this paper, resin flow patterns depending on several gate positions were investigated by numerical analyses of a simple strip part with a hinge. As a result, we found that the properly determined gate location leads to better resin flow and shorter hesitation time. Finally, injection molding tryouts using a mold that was designed one of the proposed gate systems were conducted using polypropylene that contained 20% talc. The experiment showed that hinges without defects could be produced by using the designed gate location.

• Journal of Korean Society of Industrial and Systems Engineering
• /
• v.16 no.27
• /
• pp.43-49
• /
• 1993

The purpose of this study is to develope a computer-generated work measurement system for creating and maintaining standard data as well as labor standards applying MODAPTS(Modular Arrangement of Predetermined Time Standards) technique. The system consists of three major parts. The first part is a work measurement program applying MODAPTS technique for work standards. The second part is a work scheduling program which calculate each operator's machine and job allocations, operation and load schedules, wage and wage incentives and direct labor costs etc. The last part is the case study application program for R-Instrument Manufacturing Industry. The whole system is programmed by dbase-Ⅲ and by pop-up mu for IBM PC compatibles.

• Proceedings of the Korean Geotechical Society Conference
• /
• 1999.02a
• /
• pp.14-22
• /
• 1999

Daylight collapse have been occurred by about 6.$^{0}$ m deep at ground surface which connected to the ground surface and excessive overbreak have been occurred by the space and height of 3.$^1$~6.$^2$m at crown head part of the tunnel during tunnelling of lower-half part after completing upper-half part on tunnelling of a phyllite mountain by NATM method at the construction work of two way-double track national road. This study is a successful illustration case of earth improvement by confirming structural safety of the tunnel in a whole through solving the cause of the tunnel collapse and the work have completed successfully through applying such earth strengthening method as cement mortarㆍcement milk injection, S.G.R, steel pipe reinforced multi-step grouting etc.

• Design & Manufacturing
• /
• v.6 no.1
• /
• pp.34-38
• /
• 2012

Test work is the press die branch at The Korea-China-Japan Grand Prize Contest. This study focuses on strip layout design for test work. A comparison is drawn between product shape and blank deployment line. During the forming analysis of the whole product, shape part of the total forming process is analyzed. As for forming part and flange deployment, forming analysis is carried out in part during the mid process. Material utilization is 42.6 percent and strip layout design is completed in 14 processes that are comprised of hourglass, slotting, embossing, drawing and trimming.

• Korean Journal of Veterinary Research
• /
• v.53 no.4
• /
• pp.207-210
• /
• 2013

Fifteen dry dentate and complete mandible samples from the White Rasquera goat breed were studied for symmetry. Thirty-one landmarks were digitally located on the images of the lateral and medial aspects of each hemimandible. Distances between these landmarks allowed the evaluation of the whole hemimandible and also the neural mandible. In the studied samples, the mandible was rather symmetrical, especially in the medial neural part, and in general, there was no side dominance. Only the diastema differed significantly between the sides, and this was related to the rostral part (incisive arch). The incisive region was the least symmetrical region of the caprine mandible, indicating a modular structure more conservative for the neural part. If unsigned asymmetry is interpreted as a measure of developmental stability, then the studied breed presented a marked ability to develop in good fitness despite the harsh environment. The measurements presented here can also be used as a reference for researchers designing experimental studies, especially on mandibular catch-up growth, and as an aid for zooarchaeologists comparing results from dead animals with those from living goat populations.

• 보존과학연구
• /
• s.26
• /
• pp.41-56
• /
• 2005

A set of horse bit from the Eonnam-ri site consists of three parts, pyo , ham , andinsu , and each part takes a shape of a piece of bar. According to current typological study, the pyo is S type, the insu is two-braided line type, and the outer rim of the ham is double rim type, respectively. According to X-ray test, inlaid design seems to have been decorated on the whole surface of the iron bit, originally. However, inlaid pattern partially remained. While the part of bit stopper is designed with flame pattern, the part of rein joint is designed with cloud pattern. According to XRF and XGT analysis of inlaid material, the content of silver is not more than 50%. The line inlay method making grooves on the surface of iron, then in laying a silver thread into them, and grinding the surface in a direction was adoptedin the manufacture of the iron bit.

• Journal of Korean Institute of Industrial Engineers
• /
• v.17 no.1
• /
• pp.75-82
• /
• 1991

This research is concerned with Machine-Part Group Formation(MPGF) methodology for Flexible Manufacturing Systems(FMS). The purpose of the research is to develop a new heuristic algorithm for effectively solving MPGF problem. The new algorithm is proposed and evaluated by 100 machine-part incidence matrices generated. The performance measures are (1) grouping ability of mutually exclusive block-diagonal form. (2) number of unit group and exceptional elements, and (3) grouping time. The new heuristic algorithm has the following characteristics to effectively conduct MPGF : (a) The mathematical model is presented for rapid forming the proper number of unit groups and grouping mutually exclusive block-diagonal form, (b) The simple and effective mathematical analysis method of Rank Order Clustering(ROC) algorithm is applied to minimize intra-group journeys in each group and exceptional elements in the whole group. The results are compared with those from Expert System(ES) algorithm and ROC algorithm. The results show that the new algorithm always gives the group of mutually exclusive block-diagonal form and better results(85%) than ES algorithm and ROC algorithm.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.12 no.3
• /
• pp.61-68
• /
• 2013

Automatic measurement system is required since cycle time and cost of production are increased by various factors in manual systems. This paper presents a machine vision based prototype measurement system for the automotive axisymmetric shape parts which are generally measured by a manual system that is required the tolerance of the part is very small on each machined surface. This measurement system adopts a method in which optical lens is transferred along the profile of the part to minimize measurement cycle time. The main interest of this paper is a development of an optimum measurement algorithm to the outside diameter of the parts that can be applied to various combinations of hardware. The operating system used to implement the whole system is Window XP and corresponding environment.