• 한국원자력학회:학술대회논문집
• /
• 한국원자력학회 1997년도 춘계학술발표회논문집(1)
• /
• pp.57-61
• /
• 1997

A Canadian Deuterium Uranium (CANDU) reactor core calculation was performed using lattice parameters generated by HELIOS. The HELIOS-based lattice parameters were processed by TABGEN in a form suitable for the core analysis code RFSP. The core calculation was performed and the results were compared to those of the reference calculation which uses POWDERPUFS-V (PPV) for the lattice parameter generation. The characteristics of the core calculated based on the PPV and HELIOS lattice parameters match within 0.4%$\Delta$k and 7% for the excess reactivity and the channel power distribution, respectively.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2015년도 제46회 하계학술대회
• /
• pp.416-417
• /
• 2015

In this study, the parameters of the lightning flashover rate calculation algorithm in South Korea, USA, Japan are investigated for the suitable algorithm for South Korea. Each parameters used in each calculation algorithms have a obvious difference by the environment of the area and transmission lines, because they have different environmental parameters respectively. In this paper, the environmental parameters are weighted according to the change of outputs by different inputs, environmental parameters. In addition, the methods of the selection CRIEPI algorithm and the application EPRI, CRIEPI parameters for improvement the KEPRI algorithm are proposed.

• 한국염색가공학회지
• /
• 제11권5호
• /
• pp.38-43
• /
• 1999

A calculation method of optimum parameters on dual adsorption isotherm system was examined. The optimum parameters were obtained by non-linear regression analysis based upon a limited solute concentration of dual adsorption isotherm. The results were analyzed with adducing experimental data of formerly reported treaties. The percentage mean deviation of dual adsorption equation calculated with optimum parameters was less than about 5% of experimental data, which was far less than results obtained with parameters of the adduced treatises.

• Journal of Power Electronics
• /
• 제16권4호
• /
• pp.1387-1395
• /
• 2016

A method for the identification of mechanical parameters based on integral calculation is presented. Both the moment of inertia and the friction constant are identified by the method developed here, which is based on well-known mechanical differential equations. The mechanical system under test is excited according to a pre-determined low-frequency sinusoidal motion, minimizing the distortion, and increasing the accuracy of the results. The parameters are identified using integral calculation, increasing the robustness of the results against measurement noise. Experimental data are supported by simulation, confirming the effectiveness of the proposed technique. The performance improvements shown here are of use in the design of speed and position controllers and observers. Owing to its simplicity, this method can be readily applied to commercial inverter products.

• 한국원자력학회:학술대회논문집
• /
• 한국원자력학회 1996년도 춘계학술발표회논문집(2)
• /
• pp.513-518
• /
• 1996

This report presents a demonstration of application of realistic evaluation methodology to a posturated cold leg large break LOCA in a Westinghouse three-loop pressurized water reactor with 17$\times$17 fuel. The new method of this analysis can be divided into three distinct step: 1) Best Estimate Code Validation and Uncertainty Quantification 2) Realistic LOCA Calculation 3) Limiting Value LOCA Calculation and Uncertainty Combination RELAP5/MOD3/K ［1］, which was improved from RELAP5/MOD3.1, and CONTEMPT4/MOD5 code were used as a best estimate thermal-hydraulic model for realistic LOCA calculation. The code uncertainties which will be determined in step 1) were quantified already in previous study ［2］, and thus the step 2) and 3) for plant application were presented in this paper. The application uncertainty parameters are divided into two categories, i.e. plant system parameters and fuel statistical parameters. Single parameter sensitivity calculations were performed to select system parameters which would be set at their limiting value in Limiting Value Approach (LVA) calculation. Single run of LVA calculation generated 27 PCT data according to the various combinations of fuel parameters and these data provided input to response surface generation. The probability distribution function was generated from Monte Carlo sampling of a response surface and the upper 95$^{th}$ percentile PCT was determined. Break spectrum analysis was also made to determine the critical break size. The results show that sufficient LOCA margin can be obtained for the demonstration NPP.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1989년도 하계종합학술대회 논문집
• /
• pp.221-225
• /
• 1989

Direct calculation algorithm for the elements of A matrix in multimachine power systems with constant impedance loads has been suggested. Generator's rotor parameters need not be determined from the manufacturer's data. We can identify the elements of A matrix into two categories: One is related to only generator parameters, and the other is related to generator parameters, initial values, and $Z_{Bus}$ matrix.

• 한국방사선학회논문지
• /
• 제17권5호
• /
• pp.633-640
• /
• 2023

최근 근접 치료에서 방사선 차폐막을 사용하여 선량 분포를 변조하여 선량을 전달하는 정적 및 동적 변조 근접 치료 방법이 개발됨에 따라 새로운 방향성 빔 세기 변조 근접 치료에 적합한 역방향 치료 계획 및 치료 계획 최적화 알고리즘에서 선량 계산에 필요한 파라미터 및 데이터의 양이 증가하고 있다. 세기 변조 근접 치료는 방사선의 정확한 선량 전달이 가능하지만, 파라미터와 데이터의 양이 증가하기 때문에 선량 계산에 필요한 경과 시간이 증가한다. 본 연구에서는 선량 계산 경과 시간의 증가를 줄이기 위해 그래픽 카드 기반의 CUDA 가속 선량 계산 알고리즘을 구축하였다. 계산 과정의 가속화 방법은 관심 체적의 시스템 행렬 계산 및 선량 계산의 병렬화를 이용하여 진행하였다. 개발된 알고리즘은 모두 인텔(3.7GHz, 6코어) CPU와 단일 NVIDIA GTX 1080ti 그래픽 카드가 장착된 동일한 컴퓨팅 환경에서 수행하였으며, 선량 계산 시간은 디스크에서 데이터를 불러오고 전처리를 위한 작업 등의 추가 적으로 필요한 시간은 제외하고 선량 계산 시간만 측정하여 평가하였다. 그 결과 가속화된 알고리즘은 CPU로만 계산할 때보다 선량 계산 시간이 약 30배 단축된 것으로 나타났다. 가속화된 선량 계산 알고리즘은 적응방사선치료와 같이 매일 변화되는 어플리케이터의 움직임을 고려하여 새로운 치료 계획을 수립해야 하는 경우나 동적 변조 근접 치료와 같이 선량 계산에 변화되는 파라미터를 고려해야 하는 경우 치료 계획 수립 속도를 높일 수 있을 것으로 판단된다.

• Journal of information and communication convergence engineering
• /
• 제9권5호
• /
• pp.607-609
• /
• 2011

In this work, we present solutions of two problems. First, the representation of pattern recognition problem in the standard $T_{nml}$ table of the algorithm estimate calculation was considered. Second, the problem of finding the model, consisting of the optimal parameters of an algorithm was considered. Such procedure is carried out by the selection optimal values of the parameters of extreme algorithms. This serves to reduce the number of calculations in the algorithms of estimate calculation and to increase the quality of recognition process. The algorithmic data base of the developed system was based on mathematical apparatus of pattern recognition.

• 소음진동
• /
• 제4권2호
• /
• pp.155-161
• /
• 1994

The dynamic behavior of a complex mechanical structure can be identified by dividing the structure into a series of smaller structure, called sub- structure and by studying the dynamic characteristics of these components. Generally, the dynamic characteristics of mechanical structure are strongly affected by the properties of joint parameters. In this paper, to identify the dynamic characteristics of mechanical structure, and experimental identification method in which directrly measured frequency response function(FRF) is used is considered. The method does not use the procedure of complex matrix calculation but use that of real matrix calculation. To confirm this method, computer simulation is performed by using frequency response function mixed with noise, and the experimental study is performed about the simple structure. The dynamic characteristics of joint parameters and identified more accurately than in using the prcedure of complex matrix calculation.

• Industrial Engineering and Management Systems
• /
• 제2권1호
• /
• pp.1-8
• /
• 2003

Among many dimensional or dimensionless amplitude parameters, kurtosis and ID Factor are said to be sensitive good parameters for machine diagnosis. In this paper, a simplified calculation method for both parameters is introduced when impact vibration arise in the observed data. Compared with the past papers' results, this new method shows a good result which fit well. This calculation method is simple enough to be executed even on a pocketsize calculator and is very practical at the factory of maintenance field. This can be installed in microcomputer chips and utilized as a tool for early stage detection of the failure.