• Journal of Advanced Marine Engineering and Technology
• /
• v.31 no.5
• /
• pp.558-566
• /
• 2007

The performance characteristics of water-chilling heat pump using $CO_2$ with respect to variation of refrigerant charge amount was investigated experimentally. An experimental apparatus is consisted of a compressor, a gas cooler, an expansion valve, an evaporator and a liquid receiver. All heat exchangers used in the test rig are counter-flow-type heat exchangers with concentric dual tubes, which are made of copper. The gas cooler and the evaporator consist of 6 and 4 straight sections respectively arranged in parallel, each has 2400 mm length. The experimental results summarize as the followings : As the refrigerant charge ratio of $CO_2$ heat pump system increases, the discharge pressure and compressor ratio increases, but mass flow rate of refrigerant decreases. Also the compressor work increases with the increase of refrigerant charge ratio. However, the heating and cooling capacity of $CO_2$ heat pump decreases as the refrigerant charge ratio increases. The maximum heating COP of $CO_2$ heat pump system presented at 0.25 refrigerant charge ratio. It is possible to confirm the optimum charge ratio of $CO_2$ heat pump system by the viewpoint of heating COP.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.22 no.9
• /
• pp.1290-1306
• /
• 1998

An experimental study has been performed on a three-dimensional boundary layer over a rotating disk with an impinging jet at the center of the disk. The objective of the present study is to investigate the turbulence statistics of the three-dimensional turbulent boundary layer, which may be regarded as one of the simplest models for the flow in turbomachinery. Six components of the Reynolds stresses and ten triple products are measured by aligning the miniature X-wire probe to the mean velocity direction. The ratio of the wall-parallel shear stress magnitude to twice the turbulent kinetic energy in the near-wall region is strongly decreased by the impinging jet. In the case of the free rotating disk flow the shear stress vector lags behind the mean velocity gradient vector in the whole boundary layer, while the lag is weakened as the impinging jet speed increases.

• Korean Journal of Air-Conditioning and Refrigeration Engineering
• /
• v.22 no.2
• /
• pp.78-85
• /
• 2010

A dynamic model has been developed to investigate the operability of a single and double-effect solar energy assisted parallel type absorption chiller. In the study, main components and fluid transport mechanism were modeled. And solar radiation and the solar collector were also modeled along with its control design. The model was run for the single mode with solar energy supply only and the solar/gas driving double effect mode. From the simulation results, it was found that the present configuration of the chiller is not capable of regulating solution flow rates according to variable solar energy input. And the issues of the excessive circulation flow rate and the mismatch between available solar power and cooling load discourages the use of the single mode, but the dual use of gas and solar power is recommendable in view of controllability and enhanced COP.

• Journal of the Korea Society of Computer and Information
• /
• v.21 no.9
• /
• pp.1-9
• /
• 2016

Recent embedded processors employ set-associative L1 instruction cache to improve the performance. The energy consumption in the set-associative L1 instruction cache accounts for considerable portion in the embedded processor. When an instruction is required from the processor, all ways in the set-associative instruction cache are accessed in parallel. In this paper, we propose the technique to reduce the energy consumption in the set-associative L1 instruction cache effectively by accessing only one way. Gshare branch predictor is employed to predict the instruction flow and determine the way to fetch the instruction. When the branch prediction is untaken, next instruction in a sequential order can be fetched from the instruction cache by accessing only one way. According to our simulations with SPEC2006 benchmarks, the proposed technique requires negligible hardware overhead and shows 20% energy reduction on average in 4-way L1 instruction cache.

• Journal of Biosystems Engineering
• /
• v.27 no.2
• /
• pp.79-88
• /
• 2002

This study was conducted to develop system for high speed rice transplanting machines. The control system includes a sensor detecting the tilt angle of the seedling bed, a micro-controller and a hydraulic system consisting of a double acting cylinder, a four-way three-position solenoid valve, a relief valve and a hydraulic pump. The levelling system shared the pump with the existing steering control, resulting in a tandem center circuit for the steering and levelling control systems. Using the input signal from the sensor, the micro-controller determined and generated the output signal to control the cylinder through the solenoid valve to keep the seedling bed always parallel to the water surface regardless of soil unevenness during the transplanting operations. Both an ON/OFF and a PWM control schemes were tested. When the flow rate was more than 1 ι/min in the ON/OFF control, the system showed unstable rolling. However, in the PWM control, the system worked stably although the flow rate was more than 1 ι/min. The PWM control showed a better performance when a large difference between the angle and the dead band of the control system occurred. The characteristics of tile system response to given tilt angles were predicted by a computer simulation. Both the ON/OFF and the PWM control systems worked well providing that the operating and waiting times were properly adjusted.

• Journal of Soil and Groundwater Environment
• /
• v.19 no.3
• /
• pp.66-81
• /
• 2014

A Fortran program was developed to determine the optimal locations of an artificial recharge well. Three objective functions were considered: (1) maximizing the recovery rates, (2) maximizing the injection rates, and (3) minimizing the coefficient of variation of the increased pumping rates. We also suggested a new aggregate objective function which combined the first and the third objective functions. The model results showed that locating the injection well inside the cluster of pumping wells was desirable if either the recovery or the injection rate was taken into account. However, the injection well located outside the cluster evenly increased the pumping rates in existing pumping wells. Therefore, for clustered pumping wells, installing an injection well at the center or the upstream of the pumping wells seems beneficial. For linear arrangement of pumping wells parallel to the constant head boundary, locating the injection well in the upstream was recommended. On the contrary, in case of the linear arrangement perpendicular to the constant head boundary, the injection well installed on both sides of the central part of the pumping wells was preferable.

• Solar Energy
• /
• v.20 no.1
• /
• pp.97-108
• /
• 2000

The purpose of this study is to minimize the heat transfer surface area and cold fluid exit temperature of heat exchanger which applied to the refrigeration and air-conditioning system by utilizing the thermoelectric principle. Both uniform and non-uniform current distribution methods which applied to the analysis of the TE elements that incorporates heat exchanger were investigated. The non-uniform current distribution method had the better coefficient of performance and had the lower cold fluid exit temperature of the TE cooling system than the uniform current distribution method. It was found that if a TE cooling system incorporates a heat exchanger, a non-uniform current distribution should guarantee to the lowest cold fluid exit temperature. Also, the hybrid method (combination of the uniform and non-uniform current distribution method) is investigated to achieve the best results by combining the uniform and non-uniform current distributions. The results show that it can lower the cold fluid exit temperature and reduce the heat transfer surface area for the parallel flow arrangement if we apply the constant current in some entry region and the non-uniform increasing current in the direction of the cold fluid flow afterwards.

• Nuclear Engineering and Technology
• /
• v.54 no.7
• /
• pp.2453-2466
• /
• 2022

Nuclear power plant operators in the main control room are exposed to stressful conditions in emergency situations as immediate and appropriate mitigations are required. While emergency operating procedures (EOPs) provide operators with the appropriate tasks and diagnostic guidelines, EOPs have static properties that make it difficult to reflect the dynamic changes of the plant. Due to this static nature, operator workloads increase because unrelated information must be screened out and numerous displays must be checked to obtain the plant status. Generally, excessive workloads should be reduced because they can lead to human errors that may adversely affect nuclear power plant safety. This paper presents a framework for an operator support system that can substitute the initial responses of the EOPs, or in other words the immediate actions and diagnostic procedures, in the early stages of an emergency. The system assists operators in emergency operations as follows: performing the monitoring tasks in parallel, identifying current risk and latent risk causality, diagnosing the accident, and displaying all information intuitively with a master logic diagram. The risk causalities are analyzed with a functional modeling methodology called multilevel flow modeling. This system is expected to reduce workloads and the time for performing initial emergency response procedures.

• The Bulletin of The Korean Astronomical Society
• /
• v.45 no.1
• /
• pp.59.3-60
• /
• 2020

We present the results of polarization observations at submillimeter wavelengths towards Monoceros R2 (Mon R2). The polarized thermal dust emission was obtained from SCUBA-2/POL-2 at 450 ㎛ and 850 ㎛, simultaneously. This observation is a part of the JCMT BISTRO survey project. The polarization angle distributions at 450 ㎛ and 850 ㎛ are similar and the mean value of angle differences at two wavelengths is 5.5 degrees. The Mon R2 is one of massive star-forming regions containing a clear hub-filamentary structure. The hub region shows star formation activities, and surrounding filaments provide channels for matters to move into the hub region. It is not well known the role of magnetic fields in a hub-filamentary structure. Some studies have shown well-ordered polarization segments along a filamentary structure and magnetic field morphology traced by polarization segments is interpreted as to help gas flow along the filamentary structrue. Our observations shows that filaments in Mon R2 have spiral structure and the magnetic field lines are parallel to the filaments. We interpret that the spiral structure can be formed by a rotation hub-filament system with gas flowing along the filaments to the hub. We found several dust clumps at the central part of the hub region of the Mon R2. They seems to be formed at locations where spiral field lines meet each other. These results show one observational example that a magnetic field play a role in gas flow.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.31 no.4B
• /
• pp.343-352
• /
• 2011

The water quantity by intake station as well as the tributary flow discharge acting as sink or source were added to the main flow rate in the present study and RMA-2 and RMA-4 models were applied to the reach from Pal-dang dam to Jam-sil submerged weir to investigate the influence of water supply withdrawal on the river flow and water quality. The numerical results revealed that the water supply withdrawal from 5 intake stations located upstream of Jam-sil submerged weir changed the total flow rate and therby induced different hydraulic characteristics in terms of water surface elevation and velocity. The changed flow field by the inclusion of water intake quantity led to the variation of water quality. By the consideration of the water supply withdrawal, the velocity structure was significantly disturbed by the outflowing flow condition nearby Gu-ui, Ja-yang, and Pung-nap intake stations. Furthermore, the mean velocity was lowered by 25% and the stage upstream of Gu-ui station rose upto 1.5 cm compared with the result by exclusion of water intake. In case of no water withdrawal, the distribution of BOD concentration was parallel throughout the domain. However, when the water withdrawal is considered, the distribution of BOD concentration nearby the Gu-ui, Am-sa, and Ja-yang station was signifiantly changed. In addition, the BOD concentration including the intake stations showed higher value at the downstream of the reach due to the loss of the discharge by water withdrawal effect. It is concluded that both the inflow and outflow discharges from tributaries and water intake stations should be included in the numerical simulation to analyze the hydrodynamic behaviors and mixing characteristics more accurately.